Siemens 400 V / 210...590 A operating instructions 12-18

Parameter List							01.2004
PNU	Parameter Name in OP1				Range	# of Indices		read:		_/_
					[Unit]	Factory		write:		_/_
*:conf-P	Description				Value Texts	Settings
P557	Src3 OFF2 (coast)				1 to 5001	2		2 /	BR
*	Source 3 of the OFF2 control command (control word 1, bit 1)					i001=1		2 /	BR
22DHex	See P555 for description					i002=1
	B/R parameter
	Type=L2; PKW: PKW format(HEX)=param.value			PZD Gr.: 0
P561	Src InvRelease				0 to 5001	2		3 /	BR
*	Source for the inverter enable command (control word 1, bit 3)					i001=1		3 /	BR
231Hex	See Section "Control word" for details					i002=1
	Parameter values: 0: Disable inverter
		1: Automatically when delay timers run
		down
	Other values:	See permissible settings in Section "Control
		word"
	B/R parameter	(process data connections of control word)
	Type=L2; PKW: PKW format(HEX)=param.value			PZD Gr.: 0
P565	Src1 Fault Reset				0 to 5001	2		2 /	BR
*	Source 1 of "Acknowledge" control command (control word 1,					i001=0		2 /	BR
235Hex	bit 7)					i002=1003
	See Section "Control word" for details
	Parameter values: 0:		No source selected
		1:	Illegal setting
		1003: Digital input 3 on CUSA
	Other values:	See permissible settings in Section "Control
		word"
		(process data connections of control word)
	Note: The "Acknowledge" control command is edge-triggered.
	B/R parameter
	Type=L2; PKW: PKW format(HEX)=param.value			PZD Gr.: 0
P566	Src2 Fault Reset				0 to 5001	2		2 /	BR
*	Source 2 of "Acknowledge" control command (control word 1,					i001=0		2 /	BR
236Hex	bit 7)					i002=0
	See P565 for description
	B/R parameter
	Type=L2; PKW: PKW format(HEX)=param.value			PZD Gr.: 0
P567	Src3 Fault Reset				0 to 5001	2		2 /	BR
*	Source 3 of "Acknowledge" control command (control word 1,					i001=2001		2 /	BR
237Hex	bit 7)					i002=2001
	See P565 for description
	B/R parameter
	Type=L2; PKW: PKW format(HEX)=param.value			PZD Gr.: 0
P568	Src Jog1 ON				0 to 5001	2		2 /	BR
*	Source for the Inching 1 setpoint (control word 1, bit 8)					i001=0		2 /	BR
238Hex	See Section "Control word" for details					i002=0
	Parameter values: 0:		No inching
		1:	Illegal setting
		2001: SST1, word 1 bit 8
	Other values:	See permissible settings in Section "Control
		word"
	B/R parameter	(process data connections of control word)
	Type=L2; PKW: PKW format(HEX)=param.value			PZD Gr.: 0

12-18	6SE7087-6CX86-2BA1 Siemens AG
	Operating Instructions SIMOVERT MASTERDRIVES AFE