Siemens 400 V / 210...590 A operating instructions Drive data

Parameter List 01.2004

12.3Drive data

PNU	Parameter Name in OP1					Range	# of Indices	read:			_/_
						[Unit]	Factory	write:			_/_
*:conf-P	Description					Value Texts	Settings
P070	MLFB(6SE70..)					0 to 255	−	3	/U BR
*	MLFB (order number) of basic unit						0	3	/U
46Hex	For parameter values, see Section "Initialization"
	Type=O2;		PKW: 1HEX=1		PZD Gr.: -
P071	Line volts					90 to 1320	−	2	/ ABR
47Hex	Line supply voltage for AFE (r.m.s. of line-to-line voltage)					[V]	←	2	/	A
	This parameter specifies the incoming AC supply voltage.
	It is used to calculate the setpoint DC link voltage (P125) and
	the thresholds for fault messages "Line supply overvoltage",
	"Line supply undervoltage" (P074) and "DC link undervoltage".
	Type=O2;		PKW: 1HEX=1 V		PZD Gr.: 0
P072	AFE current(n)					4.0 to 6540.0	−	2	/U ABR
48Hex	AFE rated output current					[A]	←	4	/U
	Type=O2;		PKW: 1HEX=0.1 A		PZD Gr.: 0
P074	Undervoltage threshold					6 to 100	−	2	/	BR
4AHex	Response threshold for shutdown on line undervoltage. The					[%]	65	2	/	BR
	line supply voltage (P071) is the reference quantity.
	Note:	P155: Maximum power failure time
	Type=O2;		PKW: 1HEX=1 %		PZD Gr.: −
P077	FactSettingType					0 to 4	−	3	/U BR
*	Selective factory setting						0	3	/U
4DHex	This parameter can be changed in the "MLFB Input" state
	(P052). If no MLFB has yet been entered, the selected factory
	setting type becomes effective immediately an MLFB number
	is entered and "MLFB Input" deselected (P052=0).
	It is possible to activate a specific factory setting by selecting
	"Par. Reset" (P052 = 1 or P970 = 0). This action does not,
	however, change the setting in P077.
	Parameter values:
	0: Current factory setting remains valid.
	1: AFE with OP:			⇒not currently implemented
	2: AFE cabinet unit with terminal strip:
	This setting initializes the following parameters to values
	other than zero:
	P554, P566, P603
	3: Current factory setting remains valid.
	3: AFE cabinet unit with OP:			⇒not currently implemented
	Type:O2;		PKW: 1HEX=1		PZD Gr.: -
P078	Line frequency					50 to 60	−	2	/ ABR
4EHex	Frequency of incoming AC supply					[Hz]	50	2	/	A
	Type=O2;		PKW: 1HEX=1 Hz		PZD Gr.: −
P080	Line filter C/mF					0.000 to 10.000	−	3	/ BR
	Capacitance of the filter capacitors of one phase of the AFE						0.000	3	/	BR
50Hex	line filter in mF for a "star circuit configuration". If the line filter
	capacitors are connected in a “delta configuration”, then 300%
	of the value must be parameterized.
	Type=O2;		PKW: 1HEX=0.001		PZD Gr.: 0

12-6	6SE7087-6CX86-2BA1 Siemens AG
	Operating Instructions SIMOVERT MASTERDRIVES AFE