Siemens 400 V / 210...590 A operating instructions 12-21

01.2004								Parameter List
PNU		Parameter Name in OP1					Range	# of Indices	read:		_/_
							[Unit]	Factory	write:		_/_
*:conf-P		Description					Value Texts	Settings
P589		Src No Ext Warn2					1 to 5001	2	3 /	BR
*		Source for control command "External alarm 2" (control word 2,						i001=1	3 /	BR
24DHex		bit 29)						i002=1
		Parameter values: 0: Illegal setting
				1:	No alarm
		Other values:		See permissible settings in Section "Control
				word"
		B/R parameter		(process data connections of control word)
		Type=L2; PKW: PKW format(HEX)=param. value				PZD Gr.: 0
P590		Src Base/Reserve					0 to 5001	−	3 /	BR
*		Source for basic / reserve setting switchover command (control						1005	3 /	BR
24EHex		word 2, bit 30)
		Parameter values: 0:			Basic setting
				1:	Reserve setting
				1005: CUSA digital input 5
		Other values:		See permissible settings in Section "Control
				word"
				(process data connections of control word)
		Type=L2; PKW: PKW format(HEX)=param.value				PZD Gr.: 0
P600		Dst Ready for ON					0 to 5002	3	3 /	BR
*		Destination of the status bit 'Ready for ON' (status word 1, bit						i001=0	3 /	BR
258Hex	0)							i002=0
		Power is ON, the drive can be switched on.						i003=0
		Parameter values:
		Depending on the selected index, all settings specified in
		Section "Status word" (process data connections of status
		word) may be parameterized.
		Indices:	i001: GG:		Select a terminal on the basic unit
			i002: SCI:		Select a terminal on SCI1/2
			i003: TSY:		Select a terminal on TSY
		Type=L2; PKW: PKW format(HEX)=param.value				PZD Gr.: 0
P601		Dst Rdy for Oper					0 to 5002	3	3 /	BR
*		Destination of status bit "Ready to Run" (status word 1, bit 1)						i001=0	3 /	BR
259Hex		The DC link is charged, the pulses can be enabled.						i002=0
		Parameter values, indices as for P600						i003=0
		Type=L2; PKW: PKW format(HEX)=param.value				PZD Gr.: 0
P602		Dst Operation					0 to 5002	3	2 /	BR
*		Destination of status bit "Run" (status word 1, bit 2)						i001=0	2 /	BR
25AHex		The device is running.						i002=0
		Parameter values, indices as for P600						i003=0
		Type=L2; PKW: PKW format(HEX)=param.value				PZD Gr.: 0
P603		Dst Fault					0 to 5002	3	2 /	BR
*		Destination of status bit "Fault" (status word 1, bit 3)						i001=0	2 /	BR
25BHex		Note:	The active status (bit has H level) is output via the					i002=0
			terminal in inverted form (broken-wire proof).					i003=0
		Parameter values, indices as for P600
		Type=L2; PKW: PKW format(HEX)=param.value				PZD Gr.: 0

Siemens AG 6SE7087-6CX86-2BA1	12-21
SIMOVERT MASTERDRIVES AFE Operating Instructions