Siemens 400 V / 210...590 A operating instructions 12-22

Parameter List						01.2004
PNU	Parameter Name in OP1			Range	# of Indices		read:		_/_
				[Unit]	Factory		write:		_/_
*:conf-P	Description			Value Texts	Settings
P604	Dst NO OFF2			0 to 5002	3		3 /	BR
*	Destination of the status bit 'No OFF2 command' (status word				i001=0		3 /	BR
25CHex	1, bit 4)				i002=0
	Parameter values, indices as for P600				i003=0
	Type=L2; PKW: PKW format(HEX)=param.value		PZD Gr.: 0
P606	Dst ON blocked			0 to 5002	3		3 /	BR
*	Destination of the status bit "Starting lockout active" (status				i001=0		3 /	BR
25EHex	word 1, bit 6)				i002=0
	Note:	The active status (bit has H level) is output via the			i003=0
		terminal in inverted form (broken-wire proof).
	Parameter values, indices as for P600
	Type=L2; PKW: PKW format(HEX)=param.value		PZD Gr.: 0
P607	Dst Warning			0 to 5002	3		2 /	BR
*	Destination of the status bit "Alarm" (status word 1, bit 7)				i001=0		2 /	BR
25FHex	Note:	The active status (bit has H level) is output via the			i002=0
		terminal in inverted form (broken-wire proof).			i003=0
	Parameter values, indices as for P600
	Type=L2; PKW: PKW format(HEX)=param.value		PZD Gr.: 0
P608	Trg Bit Deviat.			0 to 5002	3		3 /	BR
*	Destination of the status bit "DC-link voltage setpoint = Actual				i001=0		3 /	BR
260Hex	DC-link voltage' (status word 1, bit 8) - cf. P517; see Section				i002=0
	"Status word" for details				i003=0
	Parameter values, indices as for P600
	Type=L2; PKW: PKW format(HEX)=param.value		PZD Gr.: 0
P611	Dst Low Voltage			0 to 5002	3		3 /	BR
*	Destination of the status bit "Low voltage' (status word 1, bit 11)				i001=0		3 /	BR
263Hex	Note:	The active status (bit has H level) is output via the			i002=0
		terminal in inverted form (broken-wire proof).			i003=0
	Parameter values, indices as for P600
	Type=L2; PKW: PKW format(HEX)=param.value		PZD Gr.: 0
P612	Dst Contactor			0 to 5002	3		3 /	BR
*	Destination of the status bit "Energize main contactor'				i001=1002		3 /	BR
264Hex	(status word 1, bit 12); H level: Energize contactor!				i002=0
	CAUTION:	For safety reasons, this status bit is always			i003=0
		connected to digital output 2 on the CUSA board
		on the AFE. It is not possible or permissible to
		connect the bit in any other way as it protects the
		AFE against damage by preventing the main
		contactor from closing before the DC link has
		been charged.
	Type=L2; PKW: PKW format(HEX)=param.value		PZD Gr.: 0
P614	Dst.Gen.Mot.			0 to 5002	3		3 /	BR
*	Destination of the status bit "Generator/motor operation" (status				i001=0		3 /	BR
266Hex	word 1, bit 14)				i002=0
	Meaning:	L: Motor-mode operation (rectifier)			i003=0
		H: Generator-mode operation (regen. feedback)
	Parameter values, indices as for P600
	Type=L2; PKW: PKW format(HEX)=param.value		PZD Gr.: 0

12-22	6SE7087-6CX86-2BA1 Siemens AG
	Operating Instructions SIMOVERT MASTERDRIVES AFE