214 | SMC Networks SMC6724L3 manual

COMMAND LINE INTERFACE

Example

The following shows the IGMP groups currently active on VLAN 1:

Console#show ip igmp groups vlan 1

GroupAddress InterfaceVlan Lastreporter Uptime Expire V1Timer

--------------- --------------- --------------- -------- -------- ---------

234.5.6.8	1	10.1.5.19	7068	220	0
Console#


Field	Description
GroupAddress	IP multicast group address with subscribers directly attached or
	downstream from this switch.

InterfaceVlan	The interface on this switch that has received traffic directed to
	the multicast group address.

Lastreporter	The IP address of the source of the last membership report
	received for this multicast group address on this interface. If no
	membership report has been received, this object has the value
	0.0.0.0.

Uptime	The time elapsed since this entry was created.

Expire	The time remaining before this entry will be aged out.
	(The default is 260 seconds.)

V1Timer	The time remaining until the switch assumes that there are no
	longer any IGMP Version 1 members on the IP subnet attached
	to this interface. (The default is 400 seconds.)

4-214

Image 500

SMC Networks SMC6724L3 manual 214, Following shows the Igmp groups currently active on Vlan

Contents

TigerSwitch 10/100 Page TigerSwitch 10/100 Management Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Contents Viii Contents Contents Command Line Interface Xii Xiii Xiv Contents Xvi Xvii Xviii Xix Contents Xxi Xxii Key Features Chapter Introduction Description of Software Features ARP Description of Software Features Introduction Description of Software Features Introduction Description of Software Features System Defaults Function Parameter Default Snmp Pvid Dhcp Introduction Connecting to the Switch Configuration Options Required Connections Connecting to the Switch Remote Connections Basic Configuration Console Connection Setting Passwords Setting an IP Address Manual Configuration Dynamic Configuration Enabling Snmp Management Access Community Strings Initial Configuration Saving Configuration Settings Trap Receivers Managing System Files Managing System Files Initial Configuration Configuring the Switch Using the Web Interface Configuring the Switch Navigating the Web Browser Interface Home Panel Display Button Action Main Menu Menu Description Vlan Vlan ID Sntp UDP Routing Protocol 152 222 Displaying System Information Field Attributes Basic Configuration Displaying Switch Hardware/Software Versions Expansion Slot Indicates any installed module typeField Attributes Main Board Management Software Basic Configuration Displaying Bridge Extension Capabilities Setting the Switch’s IP Address 176 Command Usage Command Attributes Manual Configuration Using DHCP/BOOTP 219 Managing Firmware Downloading System Software from a Server Saving or Restoring Configuration Settings Downloading Configuration Settings from a Server Setting the System Clock Configuring Sntp Setting the Time Zone Configuring the Logon Password User AuthenticationResetting the System User Authentication Configuring Local/Remote Logon Authentication Command Attributes Configuring 802.1x Port Authentication User Authentication Displaying 802.1x Global Settings User Authentication Configuring 802.1x Global Settings CLI only Configuring Port Authorization Mode Authorized Displaying 802.1x Statistics Statistical Values Eapol EAP Access Control Lists Configuring Access Control Lists Setting the ACL Name and Type ACL Configuration Setting the Name and Type Configuring a Standard IP ACL Configuring an Extended IP ACL Access Control Lists Configuring the Switch Configuring a MAC ACL Configuring the Switch Binding a Port to an Access Control List Setting Community Access Strings Simple Network Management Protocol Access Mode Specifying Trap Managers and Trap Types Command Usage Dynamic Host Configuration Protocol Configuring Dhcp Relay Service 101 Configuring the Dhcp Server Address Pool Static Addresses Enabling the Server, Setting Excluded Addresses Configuring Address Pools Setting the Network Parameters Setting the Host ParametersSetting the Optional Parameters Creating a New Address Pool Examples Configuring a Network Address Pool Configuring a Host Address Pool CLI This example configures a host address pool Displaying Address Bindings Field Attributes Web Port ConfigurationDisplaying Connection Status Configuration Web Click Port, Port Information or Trunk InformationField Attributes CLI Basic information Current status CLI This example shows the connection status for Port 128 Configuring Interface Connections 125 Setting Broadcast Storm Thresholds Configuring Port Mirroring 131 Showing Port Statistics Parameter Description Etherlike Statistics Rmon Statistics Octets long excluding framing bits, but including Configuring the Switch Configuring Rate Limits CLI This example shows statistics for port Command Attribute Trunk Configuration Dynamically Configuring a Trunk Trunk Configuration Statically Configuring a Trunk 139 138 Address Table Settings Setting Static Addresses Displaying the Address Table 143 Spanning Tree Algorithm Configuration Changing the Aging Time Designated Root Bridge Port Root Port Displaying Global Settings Configuring the Switch 160 Basic Configuration of Global Settings Configuring Global SettingsGlobal settings apply to the entire switch Root Device Configuration Advanced Configuration Settings for Rstp Displaying Interface Settings AD B AD B Configuring the Switch Configuring Interface Settings CLI This example shows the STA attributes for port 100 101 102 Vlan ConfigurationOverview 103 Assigning Ports to VLANs 104 105 106 Forwarding Tagged/Untagged Frames 107 Enabling or Disabling Gvrp Global SettingDisplaying Basic Vlan Information 108 Command Attributes WebDisplaying Current VLANs Command Attributes CLI 109 Creating VLANs 110 Adding Static Members to VLANs Vlan Index 111 112 Adding Static Members to VLANs Port Index 113 Configuring Vlan Behavior for Interfaces 114 115 116 117 Enabling Private VLANs Configuring Private VLANs118 Configuring Uplink and Downlink Ports 119 120 Class of Service ConfigurationSetting the Default Priority for Interfaces 121 131 Mapping CoS Values to Egress Queues 122 123 Setting the Service Weight for Traffic Classes 124 Mapping Layer 3/4 Priorities to CoS Values 125 Selecting IP Precedence/DSCP Priority 126 Mapping IP Precedence 127 128 Mapping Dscp Priority 129 130 Mapping IP Port Priority 131 132 Copying IP Settings to Another Interface 133 Multicast Filtering 134 Igmp Protocol 135 Layer 2 Igmp Snooping and Query 136 Configuring Igmp Snooping Parameters 137 138 139 Displaying Interfaces Attached to a Multicast Router 140 Specifying Static Interfaces for a Multicast Router 141 Displaying Port Members of Multicast Services 142 Assigning Ports to Multicast Services 143 Layer 3 Igmp Query used with Multicast Routing 144 Configuring Igmp Interface Parameters 145 146 147 Displaying Multicast Group Information CLI This example configures the Igmp parameters for Vlan148 IP Routing 149 Initial Configuration 150 IP Switching 151 Routing Protocols 152Routing Path Management 153 RIP and RIP-2 Dynamic Routing ProtocolsOSPFv2 Dynamic Routing Protocol Non-IP Protocol Routing Basic IP Interface Configuration 154 Configuring IP Routing Interfaces 155 156 Address Resolution Protocol 157 158 Proxy ARP Basic ARP Configuration 159 Configuring Static ARP Addresses 160 161 Displaying Dynamically Learned ARP Entries 162 163 Displaying Local ARP Entries Web Click IP, ARP, Statistics 164Displaying ARP Statistics IP Statistics Displaying Statistics for IP Protocols165 166 167 Web Click IP, Statistics, IP CLI See the example on 168 Icmp Statistics 169 Web Click IP, Statistics, Icmp CLI See the example on Web Click IP, Statistics, UDP CLI See the example on 170UDP Statistics 171 TCP Statistics Web Click IP, Statistics, TCP CLI See the example on Configuring Static Routes172 Displaying the Routing Table 173 174 228 Configuring the Routing Information Protocol 175 Configuring General Protocol Settings 176 177 Global SettingsTimer Settings 178 Specifying Network Interfaces for RIP Configuring Network Interfaces for RIP 179 Loopback Prevention 180Specifying Receive and Send Protocol Types Protocol Message Authentication 181 182 183 Displaying RIP Information and Statistics 184 RIP Information and Statistics 185 Web Click Routing Protocol, RIP, Statistics Configuring the Open Shortest Path First Protocol 186 187 188 General Information 189 Networks in two or more areasAn area border router runs a AS Boundary Router Default Route Information 190 191 Single route. The backbone or any Configuring Ospf Areas192 193 194 195 196 271 197 Configuring Ospf Interfaces 198 Ospf Interface List Detail Interface Configuration199 200 201 202 203 Configuring Virtual Links 204 205 Configuring Network Area Addresses 206 207 Configuring Summary Addresses for External AS Routes 208 209 210 Redistributing External Routes 211 Area ID Identifier for an not-so-stubby area Nssa Configuring Nssa Settings212 213 Displaying Link State Database Information 214 215 216 Displaying Information on Border Routers 217 Displaying Information on Neighbor Routers Multicast Routing 218 219 Configuring Global Settings for Multicast RoutingDisplaying the Multicast Routing Table 220 221 Configuring Dvmrp 222 Configuring Global Dvmrp Settings 223 224 225 226 Dvmrp Interface Information Configuring Dvmrp Interface Settings227 228 You can display all the neighboring Dvmrp routers 229Displaying Neighbor Information CLI This example displays the only neighboring Dvmrp router 230Displaying the Routing Table Configuring PIM-DM 231 Configuring Global PIM-DM Settings 232 Configuring PIM-DM Interface Settings 233 234 235 309 236 Displaying Interface Information 237 You can display all the neighboring PIM-DM routers 238 Using the Command Line Interface Accessing the CLI Telnet Connection Keywords and Arguments Entering CommandsThis section describes how to enter CLI commands Minimum Abbreviation Command CompletionGetting Help on Commands Showing Commands Negating the Effect of Commands Using Command HistoryUnderstanding Command Modes Partial Keyword Lookup Exec Commands Vlan Database Configuration Commands Mode Command Prompt Command Line Processing Keystroke Function Command Groups Command Group Description 181 Line Commands Command Function Mode Line Login Syntax Login local no loginLogin local Line Configuration Password Username 4-33 passwordSyntax Password 0 7 password no password No password is specified Exec-timeout Login 4-15password-thresh4-18Syntax Exec-timeout seconds no exec-timeout CLI No timeout Telnet 10 minutes Password-thresh To set the timeout to two minutes, enter this commandSyntax Password-thresh threshold no password-thresh Default value is three attempts Silent-time Syntax Silent-time seconds no silent-time To specify 7 data bits, enter this command DatabitsSyntax Databits 7 8 no databits Seven data bits per character Eight data bits per character To specify no parity, enter this command ParitySyntax Parity none even odd no parity None No parity Even Even parity Odd Odd parity To specify 57600 bps, enter this command SpeedSyntax Speed bps no speed 9600 bps Stopbits Show lineSyntax Stopbits 1 Syntax Show line console vty General Commands To show all lines, enter this command Enable Syntax Enable levelDisable Enable password Level Privileged Exec DisableNone Configure Show history Use this command to restart the system Reload End Exit Quit Use this command to exit the configuration programThis example shows how to quit a CLI session System Management Commands Device Designation Commands User Access Commands HostnameSyntax Hostname name no hostname Name The name of this host. Maximum length 255 characters Username Enable password Default is level Default password is super Syntax Ip http port port-numberno ip http port Web Server CommandsIp http port Ip http server Default Setting Command ModeSyntax Ip http server no ip http server Default Setting Event Logging Commands Syntax Logging on no logging on Default SettingLogging on Logging history 4-38 clear logging Flash errors level 3 RAM warnings level 7 Logging history Use this command to clear messages from the log buffer Clear loggingSyntax Clear logging flash ram Flash and RAM Show logging Syntax Show logging flash ram Time Commands Sntp client Syntax Sntp client no sntp client Default SettingDisabled Sntp server Syntax Sntp server ip1 ip2 ip3 Sntp poll Sntp client 4-42 sntp poll 4-44 show sntpSyntax Sntp poll seconds no sntp poll Seconds Sntp broadcast client Show sntp Clock timezone System Status Commands Show startup-config Command Usage Show running-config Show running-config4-49 Show startup-config4-47 Show users Use this command to display system informationShow system Show version Flash/File Commands Copy Privileged Exec Following example shows how to download a configuration file Use this command to delete a file or image Filename Name of the configuration file or image nameDelete Syntax Use this command to display a list of files in flash memory Dir Whichboot Following example shows how to display all file information Boot system Dir 4-57 whichboot Authentication Commands Authentication SequenceAuthentication login Local Username for setting the local user names and passwords Radius Client 10.1.0.1 Radius-server hostHostipaddress IP address of server Radius-server port Radius-server keySyntax Radius-server port portnumber no radius-server port 1812 Radius-server retransmit Radius-server timeout Show radius-server 802.1x Port Authentication Authentication dot1x default Dot1x default Default Command Mode Dot1x max-reqDot1x port-control Syntax Dot1x max-req count no dot1x max-req Dot1x re-authenticate Dot1x re-authentication Seconds The number of seconds. Range Dot1x timeout quiet-periodDot1x timeout re-authperiod Dot1x timeout tx-period Show dot1x Authenticator State Machine Reauthentication State MachineState- Current state including initialize, reauthenticate Backend State Machine Access Control List Commands Access Control List Commands Access-list ip IP ACLs Permit, deny Ip access-group4-81 show ip access-list4-83 Permit, deny Standard ACL Standard ACL Permit, deny Extended ACL Extended ACL Ip access-group Syntax Ip access-group aclname in no ip access-group aclname Show ip access-group Interface Configuration EthernetShow ip access-list4-83 Use this command to show the ports assigned to IP ACLs Permit, deny 4-78,4-79 ip access-group4-81 Show ip access-listSyntax Show ip access-list standard extended aclname MAC ACLs Access-list macSyntax Access-list mac aclname no access-list mac aclname Permit, deny MAC ACL No permit deny packet-format any host source source bitmask MAC ACL Mac access-group Show mac access-groupSyntax Mac access-group aclname Show mac access-list4-88 Show mac access-list Mac access-group4-87Syntax Show mac access-list aclname Permit, deny Mac access-group4-87 ACL Information Show access-listShow access-group Snmp Commands Snmp-server community Snmp-server contact Syntax Snmp-server contact string no snmp-server contact Snmp-server location Syntax Snmp-server location text no snmp-server location Snmp-server host Snmp-server enable traps Issue authentication and link-up-down traps Use this command to check the status of Snmp communications Show snmp Example Ip dhcp client-identifier Dhcp CommandsDhcp Client Ip dhcp restart client Interface Configuration VlanUse this command to submit a Bootp or Dhcp client request Syntax Ip dhcp relay no ip dhcp relay Dhcp RelayIp dhcp restart relay 100 Usage Guidelines Ip dhcp relay serverAddress IP address of Dhcp server. Range 1-3 addresses Dhcp Server Service dhcp Syntax Service dhcp no service dhcp Default Setting Syntax Ip dhcp pool name no ip dhcp pool name Ip dhcp excluded-addressIp dhcp pool Dhcp Pool Configuration NetworkNetwork 4-105 host Network network-number mask no network Default-router Default-routeraddress1 address2 no default-router Domain-name Syntax Domain-name domain no domain-name Dns-server Dns-serveraddress1 address2 no dns-server Bootfile Syntax Bootfile filename no bootfileNext-server Syntax Next-server address no next-server address Netbios-name-server Next-server4-109 Netbios-node-type Syntax Netbios-node-type type no netbios-node-typeMixed Peer-to-peer Default Setting Broadcast Command Modes LeaseLease days hoursminutes infinite no lease One day Host Host address mask no host Client-identifier Client-identifier4-114hardware-address4-115 Ethernet Ieee802 Fddi Default Setting If no type is specified, the default protocol is EthernetHardware-address Hardware-addresshardware-address type no hardware-address Clear ip dhcp binding Syntax Clear ip dhcp binding address Show ip dhcp binding Syntax Show ip dhcp binding address Interface Commands Interface DescriptionPort-channel channel-idRange Syntax Description string no description Following example adds a description to port Interface Configuration Ethernet, Port ChannelSpeed-duplex Negotiation 4-121 capabilities Syntax Negotiation no negotiation Default SettingNegotiation Capabilities 4-122speed-duplex4-120 Following example configures port 11 to use autonegotiationCapabilities Negotiation 4-121speed-duplex4-120 flowcontrol Flowcontrol Syntax Flowcontrol no flowcontrol Default SettingFlow control enabled Syntax Shutdown no shutdown Default Setting Shutdown Switchport broadcast packet-rate Use this command to clear statistics on an interface Port-channel channel-idRange Default SettingClear counters Syntax Clear counters interface Use this command to display the status for an interface Show interfaces statusSyntax Show interfaces status interface Shows the status for all interfaces Use this command to display interface statistics Show interfaces countersSyntax Show interfaces counters interface Shows the counters for all interfaces 130 Show interfaces switchport Syntax Show interfaces switchport interfaceThis example shows the configuration setting for port Shows all interfaces Field Description Mirror Port Commands Interface Configuration Ethernet, destination portPort monitor Interface ethernet unit/port source port Use this command to display mirror information Unit Switch unit Port Port numberShow port monitor Syntax Show port monitor interface Rate Limit Commands Following shows mirroring configured from port 6 to port Rate-limit Link Aggregation Commands Guidelines for Creating Trunks Channel-group Syntax Channel-group channel-idno channel-groupChannel-id- Trunk index Range Current port will be added to this trunk Syntax Lacp no lacp Default Setting Lacp 140 Address Table Commands Mac-address-table staticMac-address- MAC address Vlan-id- Vlan ID Range Clear mac-address-table dynamic Action Show mac-address-table Mac-address- MAC address Mask Bits to match in the address Mac-address-table aging-time Seconds Time in number of seconds Show mac-address-table aging-time Spanning Tree Commands Spanning-tree Syntax Spanning-tree no spanning-tree Default SettingSpanning tree is enabled Rstp Spanning-tree modeSyntax Spanning-tree mode stp rstp no spanning-tree mode Spanning-tree forward-time Spanning-tree hello-time Spanning-tree max-age Spanning-tree priority 32768 Spanning-tree pathcost method Long method Count The transmission limit in seconds. Range This command limits the maximum transmission rate for BPDUsSpanning-tree transmission-limit Spanning-tree cost Syntax Spanning-tree cost cost no spanning-tree cost Spanning-tree port-priority Priority The priority for a port. Range 0-240, in steps Spanning-tree edge-port Spanning-tree portfast Auto Spanning-tree link-typeSpanning-treeedge-port4-156 Syntax Spanning-tree protocol-migration interface Port-channel channel-idRange Command ModeSpanning-tree protocol-migration Syntax Show spanning-tree interface Use this command to show the spanning tree configurationShow spanning-tree 161 Vlan database Vlan CommandsEditing Vlan Groups Vlan Vlan Database Configuration Configuring Vlan InterfacesBy default only Vlan 1 exists and is active Interface vlan Syntax Interface vlan vlan-id Switchport mode Syntax Switchport mode trunk hybrid no switchport modeAll ports are in hybrid mode with the Pvid set to Vlan Switchport acceptable-frame-types4-167 All frame types Switchport acceptable-frame-typesSwitchport mode Switchport ingress-filtering Switchport native vlan Switchport allowed vlan Switchport forbidden vlan No VLANs are included in the forbidden list Use this command to show Vlan information Displaying Vlan InformationShow vlan Syntax Show vlan id vlan-idname vlan-name Following example shows how to display information for Vlan PvlanPvlan up-linkinterface-list down-linkinterface-listno pvlan No private VLANs are defined Use this command to display the configured private Vlan Show pvlan Bridge-ext gvrp Gvrp and Bridge Extension CommandsSyntax Bridge-ext gvrp no bridge-ext gvrp Default Setting Show bridge-ext Switchport gvrp Syntax Switchport gvrp no switchport gvrp Default Setting Show gvrp configuration Garp timerUse this command to show if Gvrp is enabled Syntax Show gvrp configuration interface 179 Shows all Garp timers Show garp timerSyntax Show garp timer interface Priority Commands Priority Commands Layer Switchport priority default Queue bandwidth weight1...weight4 no queue bandwidth Queue bandwidth Queue cos-map Queue cos-mapqueueid cos1 ... cosn no queue cos-map Show queue bandwidth Show queue cos-map4-186 Syntax Show queue cos-map interface Use this command to show the class of service priority mapShow queue cos-map Syntax Map ip port no map ip port Default Setting Priority Commands Layer 3Map ip port Global Configuration Map ip port Interface Configuration Following example shows how to map Http traffic to CoS value Map ip precedence Global Configuration Map ip precedence Interface Configuration List below shows the default priority mapping Map ip dscp Global Configuration Map ip dscp Interface ConfigurationSyntax Map ip dscp no map ip dscp Default Setting Map ip dscp dscp-value cos cos-value no map ip dscp 192 Syntax Show map ip port interface Use this command to show the IP port priority mapShow map ip port Syntax Show map ip precedence interface Use this command to show the IP precedence priority mapShow map ip precedence Syntax Show map ip dscp interface Use this command to show the IP Dscp priority mapShow map ip dscp Multicast Filtering Commands Igmp Snooping Commands Syntax Ip igmp snooping no ip igmp snooping Default Setting Following example enables Igmp snoopingIp igmp snooping Ip igmp snooping vlan static Ip igmp snooping version Igmp Version Following configures the switch to use Igmp Version Use this command to show the Igmp snooping configurationFollowing shows the current Igmp snooping configuration Show ip igmp snooping Use this command to show known multicast addresses Show mac-address-table multicast Igmp Query Commands Layer Ip igmp snooping querier Following shows how to configure the query count to Ip igmp snooping query-countTimes Ip igmp snooping query-max-response-time4-203 Ip igmp snooping query-max-response-time Seconds The report delay advertised in Igmp queries. RangeIp igmp snooping query-interval Ip igmp snooping router-port-expire-time Igmp Commands Layer Switch must use IGMPv2 for this command to take effect Ip igmp snooping 4-197 show ip igmp snooping Syntax Ip igmp no ip igmp Default SettingIp igmp Ip igmp robustval Ip igmp query-intervalSyntax Ip igmp robustval robust-valueno ip igmp robustval Robust-value- The robustness of this interface. Range Ip igmp max-resp-interval Ip igmp version Ip igmp query-interval4-207 Seconds The report delay for the last member query. RangeIp igmp last-memb-query-interval Syntax Ip igmp version 1 2 no ip igmp version Ip igmp versionSecond Show ip igmp interface Syntax Show ip igmp interface vlan vlan-id Deletes all entries in the cache if no options are selected Use this command to delete entries from the Igmp cacheClear ip igmp group Show ip igmp groups Displays information for all known groups Following shows the Igmp groups currently active on Vlan IP Interface Commands Basic IP Configuration Ip address IP address Netmask Following example, the device is assigned an address in Vlan Ip default-gateway Syntax Ip default-gateway gateway no ip default-gateway Use this command to display the settings of an IP interface Ip default-gateway4-218Show ip interface Show ip redirects Syntax Ping host count countsize size This command has no default for the hostPing Address Resolution Protocol ARP Interface No default entries ArpArp ip-address hardware-address no arp ip-address Clear arp-cache show arp Arp-timeout Syntax Arp-timeout seconds no arp-timeoutClear arp-cache Seconds 20 minutes Syntax Ip proxy-arp no ip proxy-arp Default Setting Show arpIp proxy-arp This example displays all entries in the ARP cache IP Routing Commands Ip routing Global Routing ConfigurationSyntax Ip routing no ip routing Default Setting No static routes are configured Ip route Syntax Show ip route config address netmask Clear ip routeShow ip route Syntax Clear ip route network netmask Show ip traffic 230 Syntax Router rip no router rip Routing Information Protocol RIPRouter rip Router Configuration Timers basicTimers basic update-seconds no timers basic Network subnet-address no network subnet-address Neighbor No networks are specifiedRouter rip Syntax Neighbor ip-addressno neighbor ip-address RIP Version VersionSyntax Version 1 2 no version Ip rip receive version Ip rip receive version 4-236 ip rip send version Ip rip send version Version 238 Ip split-horizon 239Syntax Ip split-horizon poison-reverseno ip split-horizon Split-horizon Ip rip authentication key No authenticationIp rip authentication mode 240 Ip rip authentication mode Text Indicates that a simple password will be usedThis example sets the authentication mode to plain text Ip rip authentication key Syntax Show ip rip configuration status peer Show rip globalsShow ip rip 242 Show ip rip configuration 243 Open Shortest Path First Ospf 244 245 Display Information Syntax Router ospf no router ospf Command Mode Router ospf246 Network area Router-idip-address no router-id Router-id247 Default-information originate Compatible rfc1583248 RFC 1583 compatible 249 Ip route 4-227 redistribute 250 Timers spfTimers spf spf-holdtime no timers spf Area range 251 Area default-cost Default Setting Command Usage252 Area stub Area range Summary-address253 Type-value Redistribute254 255 Default-information originateNetwork area 256 No stub is configured Area stub257 Syntax Area area-idstub summary no area area-idstub summary Area default-cost4-252 No Nssa is configuredArea nssa 258 259 Area virtual-link 260 261 Show ip ospf virtual-links4-284 262Area-id None Router-id None Ip ospf authentication 263 Ip ospf authentication-key 264 265 MD5 authentication is disabledIp ospf message-digest-key Syntax Ip ospf cost cost no ip ospf cost Ip ospf cost266 Ip ospf hello-interval4-268 Ip ospf dead-interval267 Ip ospf hello-interval Ip ospf priority268 Syntax Ip ospf priority priority no ip ospf priority Ip ospf retransmit-interval 269 Ip ospf transmit-delay 270 Show ip ospf 271 Show ip ospf border-routers 272 Show ip ospf database 273 Following shows output for the show ip ospf database command 274 Following shows output when using the asbr-summarykeyword 275 Following shows output when using the external keyword 276 277 Following shows output when using the network keyword 278 Following shows output when using the router keyword 279 Following shows output when using the summary keyword 280 Show ip ospf interface 281 282 Syntax Show ip ospf neighbor Command ModeShow ip ospf neighbor Use this command to display all summary address information Syntax Show ip ospf summary-address Command ModeShow ip ospf summary-address 283 Syntax Show ip ospf virtual-links Command Mode Show ip ospf virtual-links284 Summary-address4-253 285 Multicast Routing CommandsStatic Multicast Routing Commands 286 No static multicast router ports are configuredIp igmp snooping vlan mrouter General Multicast Routing Commands Displays multicast router ports for all configured VLANsShow ip igmp snooping mrouter 287 Use this command to display the IP multicast routing table Ip multicast-routingShow ip mroute 288 289 Dvmrp Multicast Routing Commands 290 291 Syntax Router dvmrp no router dvmrp Command ModeRouter dvmrp Probe-interval 292Ip dvmrp Show router dvmrp Syntax Probe-interval seconds Nbr-timeout Syntax Nbr-timeout secondsReport-interval 293 Flash-update-interval Syntax Flash-update-interval secondsPrune-lifetime 294 Default-gateway Syntax Default-gateway ip-addressno default-gatewayIp-address- IP address of the default Dvmrp gateway 295 296 Syntax Ip dvmrp no ip dvmrp Default SettingIp dvmrp Ip dvmrp metric interface-metric no ip dvmrp metric Ip dvmrp metric297 298 Clear ip dvmrp routeShow router dvmrp Default settings are shown in the following example Show ip dvmrp route299 Dmvrp routes are shown in the following example Show ip dvmrp neighbor 300 301 PIM-DM Multicast Routing CommandsShow ip dvmrp interface 302 Syntax Router pim no router pim Default SettingRouter pim 303 Syntax Ip pim dense-mode no pim dense-mode Default SettingIp pim dense-mode Ip pim hello-interval 304Syntax Ip pim hello-interval seconds no pim hello-interval Seconds Interval between sending PIM hello messages. Range Ip pim hello-holdtime Ip pim trigger-hello-interval305 Seconds The hold time for PIM hello messages. Range Seconds The hold time for the prune state. Range Ip pim join-prune-holdtime306 Seconds The time before resending a Graft. Range Ip pim graft-retry-interval307 308 Ip pim max-graft-retriesShow router pim Show ip pim interface Show ip pim neighbor309 Syntax Show ip pim interface vlan-id 310 Appendix a Troubleshooting Troubleshooting Appendix B Upgrading Firmware VIA Serial Port Upgrading Firmware VIA the Serial Port Page Upgrading Firmware VIA the Serial Port Glossary-1 Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Glossary-7 Glossary-8 XModem Index Index-1 Index-2 Index-3 Index-4 Snmp Snmp Index-5 Index-6 Page Internet