Interface, Description | SMC Networks SMC6724L3 manual

INTERFACE COMMANDS

interface

Use this command to configure an interface type and enter interface configuration mode. Use the no form to remove a trunk.

Syntax

interface interface

no interface port-channel channel-id

interface

•ethernet unit/port

-unit - This is device 1.

-port - Port number.

•port-channel channel-id(Range: 1-6)

•vlan vlan-id(Range: 1-4094)

Default Setting

None

Command Mode

Global Configuration

Example

To specify port 25, enter the following command:

Console(config)#interface ethernet 1/25

Console(config-if)#

description

Use this command to add a description to an interface. Use the no form to remove the description.

Syntax

description string no description

string - Comment or a description to help you remember what is attached to this interface. (Range: 1-64 characters)

4-119

Image 405

SMC Networks SMC6724L3 manual Interface, Port-channel channel-idRange, Syntax Description string no description

Contents

TigerSwitch 10/100 Page TigerSwitch 10/100 Management Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Contents Viii Contents Contents Command Line Interface Xii Xiii Xiv Contents Xvi Xvii Xviii Xix Contents Xxi Xxii Chapter Introduction Key Features ARP Description of Software Features Description of Software Features Introduction Description of Software Features Introduction Description of Software Features Function Parameter Default System Defaults Snmp Pvid Dhcp Introduction Configuration Options Connecting to the Switch Required Connections Connecting to the Switch Remote Connections Console Connection Basic Configuration Setting an IP Address Setting Passwords Manual Configuration Dynamic Configuration Community Strings Enabling Snmp Management Access Initial Configuration Trap Receivers Saving Configuration Settings Managing System Files Managing System Files Initial Configuration Using the Web Interface Configuring the Switch Configuring the Switch Home Navigating the Web Browser Interface Button Action Panel Display Menu Description Main Menu Vlan Vlan ID Sntp UDP Routing Protocol 152 222 Field Attributes Displaying System Information Basic Configuration Expansion Slot Indicates any installed module type Displaying Switch Hardware/Software VersionsField Attributes Main Board Management Software Basic Configuration Displaying Bridge Extension Capabilities 176 Setting the Switch’s IP Address Command Attributes Command Usage Manual Configuration Using DHCP/BOOTP 219 Downloading System Software from a Server Managing Firmware Saving or Restoring Configuration Settings Downloading Configuration Settings from a Server Setting the System Clock Configuring Sntp Setting the Time Zone User Authentication Resetting the SystemConfiguring the Logon Password User Authentication Configuring Local/Remote Logon Authentication Command Attributes Configuring 802.1x Port Authentication User Authentication Displaying 802.1x Global Settings User Authentication Configuring 802.1x Global Settings CLI only Authorized Configuring Port Authorization Mode Statistical Values Displaying 802.1x Statistics Eapol EAP Configuring Access Control Lists Access Control Lists ACL Configuration Setting the Name and Type Setting the ACL Name and Type Configuring a Standard IP ACL Configuring an Extended IP ACL Access Control Lists Configuring the Switch Configuring a MAC ACL Configuring the Switch Binding a Port to an Access Control List Simple Network Management Protocol Setting Community Access Strings Specifying Trap Managers and Trap Types Access Mode Command Usage Configuring Dhcp Relay Service Dynamic Host Configuration Protocol 101 Address Pool Static Addresses Configuring the Dhcp Server Enabling the Server, Setting Excluded Addresses Configuring Address Pools Setting the Host Parameters Setting the Network ParametersSetting the Optional Parameters Creating a New Address Pool Examples Configuring a Network Address Pool Configuring a Host Address Pool Displaying Address Bindings CLI This example configures a host address pool Port Configuration Displaying Connection StatusField Attributes Web Web Click Port, Port Information or Trunk Information ConfigurationField Attributes CLI Basic information Current status 128 CLI This example shows the connection status for Port Configuring Interface Connections 125 Setting Broadcast Storm Thresholds 131 Configuring Port Mirroring Showing Port Statistics Parameter Description Etherlike Statistics Rmon Statistics Octets long excluding framing bits, but including Configuring the Switch CLI This example shows statistics for port Configuring Rate Limits Command Attribute Trunk Configuration Dynamically Configuring a Trunk Trunk Configuration 139 Statically Configuring a Trunk 138 Setting Static Addresses Address Table Settings Displaying the Address Table 143 Changing the Aging Time Spanning Tree Algorithm Configuration Designated Root Bridge Port Root Port Displaying Global Settings Configuring the Switch 160 Configuring Global Settings Global settings apply to the entire switchBasic Configuration of Global Settings Root Device Configuration Advanced Configuration Settings for Rstp Displaying Interface Settings AD B AD B Configuring the Switch CLI This example shows the STA attributes for port Configuring Interface Settings 100 101 Vlan Configuration Overview102 Assigning Ports to VLANs 103 104 105 Forwarding Tagged/Untagged Frames 106 Enabling or Disabling Gvrp Global Setting Displaying Basic Vlan Information107 Command Attributes Web Displaying Current VLANs108 109 Command Attributes CLI 110 Creating VLANs 111 Adding Static Members to VLANs Vlan Index 112 113 Adding Static Members to VLANs Port Index 114 Configuring Vlan Behavior for Interfaces 115 116 117 Configuring Private VLANs 118Enabling Private VLANs 119 Configuring Uplink and Downlink Ports Class of Service Configuration Setting the Default Priority for Interfaces120 131 121 122 Mapping CoS Values to Egress Queues 123 124 Setting the Service Weight for Traffic Classes 125 Mapping Layer 3/4 Priorities to CoS Values 126 Selecting IP Precedence/DSCP Priority 127 Mapping IP Precedence 128 129 Mapping Dscp Priority 130 131 Mapping IP Port Priority 132 133 Copying IP Settings to Another Interface 134 Multicast Filtering 135 Igmp Protocol 136 Layer 2 Igmp Snooping and Query 137 Configuring Igmp Snooping Parameters 138 Displaying Interfaces Attached to a Multicast Router 139 Specifying Static Interfaces for a Multicast Router 140 141 142 Displaying Port Members of Multicast Services 143 Assigning Ports to Multicast Services 144 Layer 3 Igmp Query used with Multicast Routing 145 Configuring Igmp Interface Parameters 146 147 CLI This example configures the Igmp parameters for Vlan 148Displaying Multicast Group Information 149 IP Routing 150 Initial Configuration 151 IP Switching 152 Routing Path ManagementRouting Protocols RIP and RIP-2 Dynamic Routing Protocols 153OSPFv2 Dynamic Routing Protocol Non-IP Protocol Routing 154 Basic IP Interface Configuration 155 Configuring IP Routing Interfaces 156 157 Address Resolution Protocol Proxy ARP 158 159 Basic ARP Configuration 160 Configuring Static ARP Addresses Displaying Dynamically Learned ARP Entries 161 162 Displaying Local ARP Entries 163 164 Displaying ARP StatisticsWeb Click IP, ARP, Statistics Displaying Statistics for IP Protocols 165IP Statistics 166 Web Click IP, Statistics, IP CLI See the example on 167 Icmp Statistics 168 Web Click IP, Statistics, Icmp CLI See the example on 169 170 UDP StatisticsWeb Click IP, Statistics, UDP CLI See the example on TCP Statistics 171 Configuring Static Routes 172Web Click IP, Statistics, TCP CLI See the example on 173 Displaying the Routing Table 228 174 175 Configuring the Routing Information Protocol 176 Configuring General Protocol Settings Global Settings Timer Settings177 Specifying Network Interfaces for RIP 178 179 Configuring Network Interfaces for RIP 180 Specifying Receive and Send Protocol TypesLoopback Prevention 181 Protocol Message Authentication 182 Displaying RIP Information and Statistics 183 RIP Information and Statistics 184 Web Click Routing Protocol, RIP, Statistics 185 186 Configuring the Open Shortest Path First Protocol 187 General Information 188 Networks in two or more areas 189An area border router runs a AS Boundary Router 190 Default Route Information 191 Configuring Ospf Areas 192Single route. The backbone or any 193 194 195 271 196 197 198 Configuring Ospf Interfaces Detail Interface Configuration 199Ospf Interface List 200 201 202 203 204 Configuring Virtual Links 205 206 Configuring Network Area Addresses 207 208 Configuring Summary Addresses for External AS Routes 209 Redistributing External Routes 210 211 Configuring Nssa Settings 212Area ID Identifier for an not-so-stubby area Nssa Displaying Link State Database Information 213 214 215 Displaying Information on Border Routers 216 Displaying Information on Neighbor Routers 217 218 Multicast Routing Configuring Global Settings for Multicast Routing Displaying the Multicast Routing Table219 220 221 222 Configuring Dvmrp 223 Configuring Global Dvmrp Settings 224 225 226 Configuring Dvmrp Interface Settings 227Dvmrp Interface Information 228 229 Displaying Neighbor InformationYou can display all the neighboring Dvmrp routers 230 Displaying the Routing TableCLI This example displays the only neighboring Dvmrp router 231 Configuring PIM-DM 232 Configuring Global PIM-DM Settings 233 Configuring PIM-DM Interface Settings 234 309 235 Displaying Interface Information 236 You can display all the neighboring PIM-DM routers 237 238 Accessing the CLI Using the Command Line Interface Telnet Connection Entering Commands This section describes how to enter CLI commandsKeywords and Arguments Command Completion Getting Help on CommandsMinimum Abbreviation Showing Commands Using Command History Negating the Effect of CommandsUnderstanding Command Modes Partial Keyword Lookup Vlan Database Exec Commands Configuration Commands Mode Command Prompt Keystroke Function Command Line Processing Command Group Description Command Groups 181 Command Function Mode Line Commands Line Syntax Login local no login LoginLogin local Line Configuration Username 4-33 password PasswordSyntax Password 0 7 password no password No password is specified Login 4-15password-thresh4-18 Exec-timeoutSyntax Exec-timeout seconds no exec-timeout CLI No timeout Telnet 10 minutes To set the timeout to two minutes, enter this command Password-threshSyntax Password-thresh threshold no password-thresh Default value is three attempts Syntax Silent-time seconds no silent-time Silent-time Databits To specify 7 data bits, enter this commandSyntax Databits 7 8 no databits Seven data bits per character Eight data bits per character Parity To specify no parity, enter this commandSyntax Parity none even odd no parity None No parity Even Even parity Odd Odd parity Speed To specify 57600 bps, enter this commandSyntax Speed bps no speed 9600 bps Show line StopbitsSyntax Stopbits 1 Syntax Show line console vty To show all lines, enter this command General Commands Syntax Enable level EnableDisable Enable password Level Disable NonePrivileged Exec Show history Configure Reload Use this command to restart the system Exit End Use this command to exit the configuration program This example shows how to quit a CLI sessionQuit Device Designation Commands System Management Commands Hostname User Access CommandsSyntax Hostname name no hostname Name The name of this host. Maximum length 255 characters Username Default is level Default password is super Enable password Web Server Commands Ip http portSyntax Ip http port port-numberno ip http port Default Setting Command Mode Syntax Ip http server no ip http server Default SettingIp http server Syntax Logging on no logging on Default Setting Event Logging CommandsLogging on Logging history 4-38 clear logging Logging history Flash errors level 3 RAM warnings level 7 Clear logging Use this command to clear messages from the log bufferSyntax Clear logging flash ram Flash and RAM Syntax Show logging flash ram Show logging Time Commands Syntax Sntp client no sntp client Default Setting DisabledSntp client Syntax Sntp server ip1 ip2 ip3 Sntp server Sntp client 4-42 sntp poll 4-44 show sntp Sntp pollSyntax Sntp poll seconds no sntp poll Seconds Show sntp Sntp broadcast client Clock timezone Show startup-config System Status Commands Command Usage Show running-config4-49 Show running-config Show startup-config4-47 Use this command to display system information Show systemShow users Show version Copy Flash/File Commands Privileged Exec Following example shows how to download a configuration file Filename Name of the configuration file or image name Use this command to delete a file or imageDelete Syntax Dir Use this command to display a list of files in flash memory Following example shows how to display all file information Whichboot Dir 4-57 whichboot Boot system Authentication Sequence Authentication CommandsAuthentication login Local Radius Client Username for setting the local user names and passwords Radius-server host Hostipaddress IP address of server10.1.0.1 Radius-server key Radius-server portSyntax Radius-server port portnumber no radius-server port 1812 Radius-server retransmit Show radius-server Radius-server timeout 802.1x Port Authentication Dot1x default Authentication dot1x default Dot1x max-req Default Command ModeDot1x port-control Syntax Dot1x max-req count no dot1x max-req Dot1x re-authentication Dot1x re-authenticate Dot1x timeout quiet-period Dot1x timeout re-authperiodSeconds The number of seconds. Range Dot1x timeout tx-period Show dot1x Reauthentication State Machine Authenticator State MachineState- Current state including initialize, reauthenticate Backend State Machine Access Control List Commands Access Control List Commands IP ACLs Access-list ip Permit, deny Ip access-group4-81 show ip access-list4-83 Standard ACL Permit, deny Standard ACL Permit, deny Extended ACL Extended ACL Syntax Ip access-group aclname in no ip access-group aclname Ip access-group Interface Configuration Ethernet Show ip access-groupShow ip access-list4-83 Use this command to show the ports assigned to IP ACLs Show ip access-list Syntax Show ip access-list standard extended aclnamePermit, deny 4-78,4-79 ip access-group4-81 Access-list mac Syntax Access-list mac aclname no access-list mac aclnameMAC ACLs No permit deny packet-format any host source source bitmask Permit, deny MAC ACL MAC ACL Show mac access-group Mac access-groupSyntax Mac access-group aclname Show mac access-list4-88 Mac access-group4-87 Show mac access-listSyntax Show mac access-list aclname Permit, deny Mac access-group4-87 Show access-list Show access-groupACL Information Snmp-server community Snmp Commands Syntax Snmp-server contact string no snmp-server contact Snmp-server contact Syntax Snmp-server location text no snmp-server location Snmp-server location Snmp-server host Issue authentication and link-up-down traps Snmp-server enable traps Show snmp Use this command to check the status of Snmp communications Example Dhcp Commands Dhcp ClientIp dhcp client-identifier Interface Configuration Vlan Use this command to submit a Bootp or Dhcp client requestIp dhcp restart client Dhcp Relay Ip dhcp restart relaySyntax Ip dhcp relay no ip dhcp relay 100 Ip dhcp relay server Address IP address of Dhcp server. Range 1-3 addressesUsage Guidelines Dhcp Server Syntax Service dhcp no service dhcp Default Setting Service dhcp Ip dhcp excluded-address Ip dhcp poolSyntax Ip dhcp pool name no ip dhcp pool name Network Dhcp Pool ConfigurationNetwork 4-105 host Network network-number mask no network Default-routeraddress1 address2 no default-router Default-router Syntax Domain-name domain no domain-name Domain-name Dns-serveraddress1 address2 no dns-server Dns-server Syntax Bootfile filename no bootfile BootfileNext-server Syntax Next-server address no next-server address Next-server4-109 Netbios-name-server Syntax Netbios-node-type type no netbios-node-type Netbios-node-typeMixed Peer-to-peer Default Setting Broadcast Lease Command ModesLease days hoursminutes infinite no lease One day Host address mask no host Host Client-identifier4-114hardware-address4-115 Client-identifier If no type is specified, the default protocol is Ethernet Ethernet Ieee802 Fddi Default SettingHardware-address Hardware-addresshardware-address type no hardware-address Syntax Clear ip dhcp binding address Clear ip dhcp binding Syntax Show ip dhcp binding address Show ip dhcp binding Interface Commands Description InterfacePort-channel channel-idRange Syntax Description string no description Interface Configuration Ethernet, Port Channel Speed-duplexFollowing example adds a description to port Syntax Negotiation no negotiation Default Setting NegotiationNegotiation 4-121 capabilities Following example configures port 11 to use autonegotiation CapabilitiesCapabilities 4-122speed-duplex4-120 Negotiation 4-121speed-duplex4-120 flowcontrol Syntax Flowcontrol no flowcontrol Default Setting Flow control enabledFlowcontrol Shutdown Syntax Shutdown no shutdown Default Setting Switchport broadcast packet-rate Port-channel channel-idRange Default Setting Use this command to clear statistics on an interfaceClear counters Syntax Clear counters interface Show interfaces status Use this command to display the status for an interfaceSyntax Show interfaces status interface Shows the status for all interfaces Show interfaces counters Use this command to display interface statisticsSyntax Show interfaces counters interface Shows the counters for all interfaces 130 Syntax Show interfaces switchport interface Show interfaces switchportThis example shows the configuration setting for port Shows all interfaces Field Description Interface Configuration Ethernet, destination port Mirror Port CommandsPort monitor Interface ethernet unit/port source port Unit Switch unit Port Port number Use this command to display mirror informationShow port monitor Syntax Show port monitor interface Following shows mirroring configured from port 6 to port Rate Limit Commands Rate-limit Guidelines for Creating Trunks Link Aggregation Commands Syntax Channel-group channel-idno channel-group Channel-groupChannel-id- Trunk index Range Current port will be added to this trunk Lacp Syntax Lacp no lacp Default Setting 140 Mac-address-table static Address Table CommandsMac-address- MAC address Vlan-id- Vlan ID Range Action Clear mac-address-table dynamic Mac-address- MAC address Mask Bits to match in the address Show mac-address-table Seconds Time in number of seconds Mac-address-table aging-time Show mac-address-table aging-time Spanning Tree Commands Syntax Spanning-tree no spanning-tree Default Setting Spanning tree is enabledSpanning-tree Spanning-tree mode Syntax Spanning-tree mode stp rstp no spanning-tree modeRstp Spanning-tree forward-time Spanning-tree max-age Spanning-tree hello-time 32768 Spanning-tree priority Long method Spanning-tree pathcost method This command limits the maximum transmission rate for BPDUs Spanning-tree transmission-limitCount The transmission limit in seconds. Range Syntax Spanning-tree cost cost no spanning-tree cost Spanning-tree cost Priority The priority for a port. Range 0-240, in steps Spanning-tree port-priority Spanning-tree edge-port Spanning-tree portfast Spanning-tree link-type Spanning-treeedge-port4-156Auto Port-channel channel-idRange Command Mode Spanning-tree protocol-migrationSyntax Spanning-tree protocol-migration interface Use this command to show the spanning tree configuration Show spanning-treeSyntax Show spanning-tree interface 161 Vlan Commands Editing Vlan GroupsVlan database Vlan Configuring Vlan Interfaces By default only Vlan 1 exists and is activeVlan Database Configuration Syntax Interface vlan vlan-id Interface vlan Syntax Switchport mode trunk hybrid no switchport mode Switchport modeAll ports are in hybrid mode with the Pvid set to Vlan Switchport acceptable-frame-types4-167 Switchport acceptable-frame-types Switchport modeAll frame types Switchport ingress-filtering Switchport native vlan Switchport allowed vlan No VLANs are included in the forbidden list Switchport forbidden vlan Displaying Vlan Information Use this command to show Vlan informationShow vlan Syntax Show vlan id vlan-idname vlan-name Pvlan Following example shows how to display information for VlanPvlan up-linkinterface-list down-linkinterface-listno pvlan No private VLANs are defined Show pvlan Use this command to display the configured private Vlan Gvrp and Bridge Extension Commands Syntax Bridge-ext gvrp no bridge-ext gvrp Default SettingBridge-ext gvrp Show bridge-ext Syntax Switchport gvrp no switchport gvrp Default Setting Switchport gvrp Garp timer Show gvrp configurationUse this command to show if Gvrp is enabled Syntax Show gvrp configuration interface 179 Show garp timer Syntax Show garp timer interfaceShows all Garp timers Priority Commands Layer Priority Commands Switchport priority default Queue bandwidth Queue bandwidth weight1...weight4 no queue bandwidth Queue cos-mapqueueid cos1 ... cosn no queue cos-map Queue cos-map Show queue cos-map4-186 Show queue bandwidth Use this command to show the class of service priority map Show queue cos-mapSyntax Show queue cos-map interface Priority Commands Layer 3 Map ip port Global ConfigurationSyntax Map ip port no map ip port Default Setting Following example shows how to map Http traffic to CoS value Map ip port Interface Configuration Map ip precedence Interface Configuration Map ip precedence Global Configuration List below shows the default priority mapping Map ip dscp Interface Configuration Map ip dscp Global ConfigurationSyntax Map ip dscp no map ip dscp Default Setting Map ip dscp dscp-value cos cos-value no map ip dscp 192 Use this command to show the IP port priority map Show map ip portSyntax Show map ip port interface Use this command to show the IP precedence priority map Show map ip precedenceSyntax Show map ip precedence interface Use this command to show the IP Dscp priority map Show map ip dscpSyntax Show map ip dscp interface Igmp Snooping Commands Multicast Filtering Commands Following example enables Igmp snooping Syntax Ip igmp snooping no ip igmp snooping Default SettingIp igmp snooping Ip igmp snooping vlan static Igmp Version Ip igmp snooping version Use this command to show the Igmp snooping configuration Following configures the switch to use Igmp VersionFollowing shows the current Igmp snooping configuration Show ip igmp snooping Show mac-address-table multicast Use this command to show known multicast addresses Ip igmp snooping querier Igmp Query Commands Layer Ip igmp snooping query-count Following shows how to configure the query count toTimes Ip igmp snooping query-max-response-time4-203 Seconds The report delay advertised in Igmp queries. Range Ip igmp snooping query-intervalIp igmp snooping query-max-response-time Ip igmp snooping router-port-expire-time Switch must use IGMPv2 for this command to take effect Igmp Commands Layer Syntax Ip igmp no ip igmp Default Setting Ip igmpIp igmp snooping 4-197 show ip igmp snooping Ip igmp query-interval Ip igmp robustvalSyntax Ip igmp robustval robust-valueno ip igmp robustval Robust-value- The robustness of this interface. Range Ip igmp max-resp-interval Seconds The report delay for the last member query. Range Ip igmp last-memb-query-intervalIp igmp version Ip igmp query-interval4-207 Ip igmp version SecondSyntax Ip igmp version 1 2 no ip igmp version Syntax Show ip igmp interface vlan vlan-id Show ip igmp interface Use this command to delete entries from the Igmp cache Clear ip igmp groupDeletes all entries in the cache if no options are selected Displays information for all known groups Show ip igmp groups Following shows the Igmp groups currently active on Vlan Basic IP Configuration IP Interface Commands IP address Netmask Ip address Following example, the device is assigned an address in Vlan Syntax Ip default-gateway gateway no ip default-gateway Ip default-gateway Ip default-gateway4-218 Use this command to display the settings of an IP interfaceShow ip interface Show ip redirects This command has no default for the host PingSyntax Ping host count countsize size Interface Address Resolution Protocol ARP Arp No default entriesArp ip-address hardware-address no arp ip-address Clear arp-cache show arp Syntax Arp-timeout seconds no arp-timeout Arp-timeoutClear arp-cache Seconds 20 minutes Show arp Syntax Ip proxy-arp no ip proxy-arp Default SettingIp proxy-arp This example displays all entries in the ARP cache IP Routing Commands Global Routing Configuration Syntax Ip routing no ip routing Default SettingIp routing Ip route No static routes are configured Clear ip route Syntax Show ip route config address netmaskShow ip route Syntax Clear ip route network netmask Show ip traffic 230 Routing Information Protocol RIP Router ripSyntax Router rip no router rip Timers basic Timers basic update-seconds no timers basicRouter Configuration Network subnet-address no network subnet-address No networks are specified NeighborRouter rip Syntax Neighbor ip-addressno neighbor ip-address Version Syntax Version 1 2 no versionRIP Version Ip rip receive version 4-236 ip rip send version Ip rip receive version Version Ip rip send version 238 239 Ip split-horizonSyntax Ip split-horizon poison-reverseno ip split-horizon Split-horizon No authentication Ip rip authentication keyIp rip authentication mode 240 Text Indicates that a simple password will be used Ip rip authentication modeThis example sets the authentication mode to plain text Ip rip authentication key Show rip globals Syntax Show ip rip configuration status peerShow ip rip 242 243 Show ip rip configuration 244 Open Shortest Path First Ospf Display Information 245 Router ospf Syntax Router ospf no router ospf Command Mode246 Network area Router-id 247Router-idip-address no router-id Compatible rfc1583 Default-information originate248 RFC 1583 compatible Ip route 4-227 redistribute 249 Timers spf Timers spf spf-holdtime no timers spf250 251 Area range Default Setting Command Usage Area default-cost252 Area stub Summary-address 253Area range Redistribute 254Type-value Default-information originate Network area255 256 Area stub No stub is configured257 Syntax Area area-idstub summary no area area-idstub summary No Nssa is configured Area default-cost4-252Area nssa 258 259 260 Area virtual-link 261 262 Area-id None Router-id NoneShow ip ospf virtual-links4-284 263 Ip ospf authentication 264 Ip ospf authentication-key MD5 authentication is disabled Ip ospf message-digest-key265 Ip ospf cost 266Syntax Ip ospf cost cost no ip ospf cost Ip ospf dead-interval 267Ip ospf hello-interval4-268 Ip ospf priority Ip ospf hello-interval268 Syntax Ip ospf priority priority no ip ospf priority 269 Ip ospf retransmit-interval 270 Ip ospf transmit-delay 271 Show ip ospf 272 Show ip ospf border-routers 273 Show ip ospf database 274 Following shows output for the show ip ospf database command 275 Following shows output when using the asbr-summarykeyword 276 Following shows output when using the external keyword 277 278 Following shows output when using the network keyword 279 Following shows output when using the router keyword 280 Following shows output when using the summary keyword 281 Show ip ospf interface Syntax Show ip ospf neighbor Command Mode Show ip ospf neighbor282 Syntax Show ip ospf summary-address Command Mode Use this command to display all summary address informationShow ip ospf summary-address 283 Show ip ospf virtual-links Syntax Show ip ospf virtual-links Command Mode284 Summary-address4-253 Multicast Routing Commands Static Multicast Routing Commands285 No static multicast router ports are configured Ip igmp snooping vlan mrouter286 Displays multicast router ports for all configured VLANs General Multicast Routing CommandsShow ip igmp snooping mrouter 287 Ip multicast-routing Use this command to display the IP multicast routing tableShow ip mroute 288 289 290 Dvmrp Multicast Routing Commands Syntax Router dvmrp no router dvmrp Command Mode Router dvmrp291 292 Probe-intervalIp dvmrp Show router dvmrp Syntax Probe-interval seconds Syntax Nbr-timeout seconds Nbr-timeoutReport-interval 293 Syntax Flash-update-interval seconds Flash-update-intervalPrune-lifetime 294 Syntax Default-gateway ip-addressno default-gateway Default-gatewayIp-address- IP address of the default Dvmrp gateway 295 Syntax Ip dvmrp no ip dvmrp Default Setting Ip dvmrp296 Ip dvmrp metric 297Ip dvmrp metric interface-metric no ip dvmrp metric Clear ip dvmrp route Show router dvmrp298 Show ip dvmrp route Default settings are shown in the following example299 Dmvrp routes are shown in the following example 300 Show ip dvmrp neighbor PIM-DM Multicast Routing Commands Show ip dvmrp interface301 Syntax Router pim no router pim Default Setting Router pim302 Syntax Ip pim dense-mode no pim dense-mode Default Setting Ip pim dense-mode303 304 Ip pim hello-intervalSyntax Ip pim hello-interval seconds no pim hello-interval Seconds Interval between sending PIM hello messages. Range Ip pim trigger-hello-interval Ip pim hello-holdtime305 Seconds The hold time for PIM hello messages. Range Ip pim join-prune-holdtime 306Seconds The hold time for the prune state. Range Ip pim graft-retry-interval 307Seconds The time before resending a Graft. Range Ip pim max-graft-retries Show router pim308 Show ip pim neighbor Show ip pim interface309 Syntax Show ip pim interface vlan-id 310 Appendix a Troubleshooting Troubleshooting Appendix B Upgrading Firmware VIA Serial Port Upgrading Firmware VIA the Serial Port Page Upgrading Firmware VIA the Serial Port Glossary-1 Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Glossary-7 XModem Glossary-8 Index-1 Index Index-2 Index-3 Snmp Snmp Index-4 Index-5 Index-6 Page Internet