Sony DVW-790WS/790WSP Function 2/2 DCC Function FIX/DCC/ADP.K, Sel Dcc, Fix, Sdi, VTR Mode, Atw

2-1. Service Mode

No.	Page	Item	Setup	Description
13	FUNCTION 2/2	DCC FUNCTION	FIX/[DCC]/ADP.K	Selects the DCC function modes when the DCC switch is set to ON.
		SEL		DCC		: Normal mode
						(Dynamic range is set by the DCC ADJUSTMENT page.)
				FIX		: Knee is corrected by the fixed dynamic range of 600%.
				ADP.K : Adaptive mode
						Detects an object which is occupying the largest area
						of a picture and automatically adjusts the knee point
						and knee slope to obtain the optimum level for the object.
		REAR BNC OUT	[VBS]/SDI/OFF	Selects the signal to be output from the rear panel VIDEO OUT
				connector when the SDI output board BKDW-702 is installed.
				VBS : Outputs the composite video signal.
				SDI	: Outputs the SDI signal.
				OFF : Set to OFF when power saving is desired.
		VTR MODE	ON/[OFF]	Set to ON when an external VTR is controlled by the VTR START
				button as it is interlocked with the DVW, when an external VTR is
				connected via the CA-702.
		REC INHIBIT	[ON]/OFF	Set to OFF when you use a built-in VTR for recording even though
				CCU is connected via CA-705/755.
				Note : When this setup is set to OFF, a viewfinder can not be
						powered on.
		ASSIGNABLE SW	[OFF]/RET/REC/	Selects function of the ASSINABLE button.
			TURBO/	OFF		: No function assigned
			AUDIO/ATW/
				RET		: RET button
			LOOPR/F.SHT
				REC		: VTR START button
				TURBO : TURBO GAIN button
				AUDIO		: The ON/OFF switch of the function to display the
						AUDIO source on VF for each channel.
				ATW		: The ON/OFF switch of the ATW function
				LOOPR : The ON/OFF switch of the loop recording function.
						(This item is displayed only when the picture cache
						board BKDW-703 is installed.)
				F. SHT		: The ON/OFF switch of the frame shutter function.
						(This item is displayed only when the frame shutter unit
						BKDW-705 is installed.)
14	WIDE SCREEN			Note : This page is displayed only in DVW-790WS/790WSP/
						709WS/709WSP only
		16:9/4:3 MODE	[16:9]/4:3	Sets the aspect ratio of the video signal output from the VIDEO
				OUT and TEST OUT connectors.
		VF ASPECT	[AUTO]/4:3/	Sets the aspect ratio on the viewfinder.
			16:9A/16:9B	AUTO : Sets the aspect ratio set by 16:9/4:3 MODE setting.
				4:3 : Sets the aspect ratio to 4:3 regardless of 16:9/4:3 MODE
						setting.
				16:9A		: Sets the aspect ratio to 16:9 regardless of 16:9/4:3 MODE
						setting (displays the area of 4:3 mode with the marker).
				16:9B		: Sets the aspect ratio to 16:9 regardless of 16:9/4:3 MODE
						setting (video level is cut in half out of the safety zone
						area on the VF screen).
		BOX/4:3/14:9	[BOX]/4:3/14:9	Sets the function of the box cursor.
		LIMITS		BOX : Operates as the normal cursor function.
				4:3	: Displays the 4:3 area when the 16:9/4:3 MODE set to 16:9.
				14:9	: Displays the 14:9 area when 16:9 is selected by the above
						described 16:9/4:3 MODE.
		16:9 BARS ID	ON/[OFF]	Turns ON/OFF the function of adding the 16:9 display to the built-
				in color bar when 16:9 is selected by the above described 16:9/4:3 MODE.
		16:9 VF ID	ON/[OFF]	Turns ON/OFF the function of adding the 16:9 display to the VF screen
				when 16:9 is selected by the above described 16:9/4:3 MODE.
2-6						DVW-790WS/709WS/707

DVW-790WSP/709WSP/707P P2V1