Sony DVW-709WS/709WSP VF Setting Zebra 1 Detect, Zebra 1 Aperture, Zebra 2 Detect, Zebra Select

2-1. Service Mode

No.	Page	Item	Setup	Description
15	VF SETTING	ZEBRA 1 DETECT	20 to 107 % ([70])	Sets the center level of the zebra 1 pattern.
		ZEBRA 1 APERTURE	1 to 20 % ([10])	Sets the width of the zebra 1 pattern.
		ZEBRA 2 DETECT	52 to 109 % ([100])	Sets the ZEBRA2 display level.
		ZEBRA SELECT	[1]/2/BOTH	Selects the zebra patterns.
		TEST OUT ZEBRA	ON/[OFF]	Turns ON/OFF the function of outputting the zebra pattern to TEST OUT.
		VF DTL LEVEL	X ([0])	Sets the VF detail amount.
16	LEVEL 1	DETAIL LVL	X ([0])	Sets the total level of the detail signal.
		H/V RATIO	X ([0])	Sets balance between the H detail signal and the V detail signal.
		DTL FREQ	X ([0])	Sets frequency (thickness) of the H detail signal.
		CRISPENING	X ([0])	Sets the crispening level of the detail signal.
		APT. LEVEL	X ([0])	Sets the high-frequency correction level.
		DTL W.CLP	X ([0])	Sets the white clip level of the V detail signal.
		DTL V B.CLP	X ([0])	Sets the level that clips the excessive level in the negative (_)
				direction of the V detail signal.
		DTL H B.CLP	X ([0])	Sets the level that clips the excessive level in the negative (_)
				direction of the H detail signal.
		LVL DEPEND	[ON]/OFF	Turns ON/OFF the level dependent function
		L.DEP.LVL	X ([0])	Sets the level that suppresses the detail signal at the low signal level.
17	LEVEL 2	KNEE APT	ON/[OFF]	Turns ON/OFF the knee aperture function.
		K.APT.LVL	X ([0])	Adjusts the detail signal amount that is added to the high light
				signal higher than the knee point.
		DTL COMB	X ([0])	Set the signal level at which the comb filter starts working.
		C.C.S.LVL	X ([0])	Sets the chroma suppression level. (NTSC only)
18	LEVEL 1#4:3			Note : This page is displayed only in DVW-790WS/790WSP/
				709WS/709WSP.
				The following settings are valid when the 16:9/4:3 MODE
				on the WIDE SCREEN is set to 4:3.
		DETAIL LVL	X ([0])	Sets the overall level of the detail signal.
		H/V RATIO	X ([0])	Sets balance between the H detail signal and the V detail signal.
		DTL FREQ	X ([0])	Sets frequency (thickness) of the H detail signal.
		CRISPENING	X ([0])	Sets the crispening level of the detail signal.
		APT. LEVEL	X ([0])	Sets the high frequency correction level.
		DTL W.CLP	X ([0])	Sets the white clip level of the V detail signal.
		DTL V B.CLP	X ([0])	Sets the level that clips the excessive level in the negative (_)
				direction of the V detail signal.
		DTL H B.CLP	X ([0])	Sets the level that clips the excessive level in the negative (_)
				direction of the H detail signal.
		LVL DEPEND	[ON]/OFF	Turns ON/OFF the level dependent function
		L.DEP.LVL	X ([0])	Sets the level that suppresses the detail signal at the low signal level.
19	LEVEL 2#4:3			Note : This page is displayed only in DVW-790WS/790WSP/
				709WS/709WSP.
				The following settings are valid when the 16:9/4:3 MODE
				on the WIDE SECREEN is set to 4:3.
		KNEE APT	ON/[OFF]	Turns ON/OFF the knee aperture function.
		K.APT.LVL	X ([0])	Adjusts the detail signal amount that is added to the high light
				signal higher than the knee point.
		DTL COMB	X ([0])	Set the signal level at which the comb filter starts working.
		C.C.S.LVL	X ([0])	Sets the chroma suppression level. (NTSC only)
DVW-790WS/709WS/707				2-7

DVW-790WSP/709WSP/707P P2V1