Shutter Switch | Sony DVW-709WS/709WSP, DVW-790WS/790WSP specification

3-3-4. Shutter Switch

1.Remove the front assembly. (Refer to “3-2-1. Replacing CCD unit”.)

2.Remove the two precision screws fixing the lens connector and the three precision screws to remove the front switch cover assembly.

3.Disconnect the harness from the connector (CN10) on the SW-971 board.

4.Remove the two screws to remove the SW-971 board.

5.Remove soldering from the shutter switch to remove the switch from the SW-971 board.

6.Reattach the shutter switch by reversing the removing steps.

n

Reattach the SW-971 board while the hole of the front shield plate is positioned on the back of the SW-971 board.

DVW-790WS/709WS/707

3-3. Replacing the External Connectors/Switches

Precision

P 2.6x5

Front assembly

Precision	Front switch cover assembly
Precision
P 2.6x5

Front switch cover assembly

Front shield plate

Shutter switch

CN10

SW-971 board

P 2.6x6

Front shield plate

Hole

S202

SW-971 board

3-21

DVW-790WSP/709WSP/707P P2V1

Image 77

Sony DVW-709WS/709WSP, DVW-790WS/790WSP manual Shutter Switch

Contents

DVW-707/707P DVW-709WS/709WSP DVW-790WS/790WSP Warnung Recycling NICKEL-CADMIUM Batteries Page Table of Contents Audio IN, Audio OUT CH1, CH2, DC IN, DC OUT Mechanical Deck Parts Replacement VTR System Alignment Tape Path Adjustment DVW-790WS/709WS/707 Camera System Electrical Alignment Only for DVW-707/707P Page Purpose of this manual Contents Related manuals Illust No. Part No Description Usage Fixtures and Adjustment EquipmentFixtures Illust No Description Usage Equipment Model Name Adjustment Equipment Using the EX-655 and EX-656 Boards Using the Extension BoardsProcedure Board to be Extension board Reference Checked When extending the DCP board assembly Using the EX-657 and EX-658 Boards DC-DC Converter Using the EX-667 BoardSV-210 Board CN2CN22 DIF-75 Board Optional Board BKDW-702CN2 Disconnecting Disconnecting/Reconnecting Flexible Card WiresReconnecting IC Link Description on CCD Block Number Description on EEPROM/NV-RAM DataSpare CCD Units Adjusting After Eeprom Replacement Setting/Adjustment After Board ReplacementEeprom on the ES-23 Board Ref. No. Address Data stored Board Setting/Adjusting after Replacement DC Fans PrecautionSetting/Adjusting After Board Replacements Page About the Setup Card Service ModeHow to Enter the Service Mode Data Structure Fundamental Operation of the Setup Menu Contents of Setup Menu Master Gain LOW White PresetMID High Write →CARD Setup Card Read →CAMID Edit Write Protect Function 2/2 DCC Function FIX/DCC/ADP.K VTR ModeSEL DCC FIX Zebra 1 Aperture VF Setting Zebra 1 DetectZebra 2 Detect Zebra Select RGB Setup LVL Burst PhaseENC Setup LVL Level Skin Tone DTL Flare Level BlackTest OUT ENC/R/G/B Level Gamma Table SC Phase Level PhaseIris Mode Iris Weight Shading G AdjustmentSAW Para Offset WHT Preset WHTOffset Whitea WARM-COOLA Operation B-G SEL BatteryLOW Light LOW Light Level Data Reset DelayService Operation AWB Level Gate VF Setting Menu SEL Setup CardMenu SEL Marker 1/3 Marker 2/3 Measurement ResolutionModulation Sensitivity Clock Phase AD Gain AD Clock PhaseND Comp ND Detection OFF/EXEC/RESET VTR ADJ EQ Adjustment Display Description MPX DP DIAG.STATUSDTL ROM Setup Menu List Turbo YES Setup C RM-P9 RM-B150 SET C-SET Remark VTR Mode YES OFF REC Inhibit CCU Assignable SW Setup CRemark Shutter EVS YES CLS SET Remark ENC Y Level YES Black Flare Test OUT YES Level SC 0/180 SEL RM-B150 SET C-SET Remark Delay YES Preset WHT Color Temp P YESREC Tally YES Upper Time Code Disp OFF Loop Recording FRM Shutter FRM Shutter Unit YES OFF YES OFF Level 11SC-H YES Function 1/2 OFF Function 2/2 VF Setting Wide ScreenYES OFF Level 143DTL Level 243DTL Menu SEL Preknee KS on Test OUT ENC Test SAW OFF BC COMP.ADJ FIELD/FRAME YES Field Test OUT ENC VsubGain TMP MOD.BAL. TMP SAW/REC Test Level Test SAW OFF YET AD ADJ AD Gain AD Clock Phase ND Comp ND Detection OFF MPX DTL ROM SV1 SV2 WSH Setup C RM-P9 RM-B150 F-SETPage Replacing Boards Section Parts Replacement MB-810 Board Replacing the MB-810 and MB-811 Boards MB-811 Board Replacing the HN-260 Board Removal Replacing the CI-20 and CI-21 Boards Replacing Boards Reinstallation Required tools Adjustments after replacement ReplacementReplacing the CCD Unit and Its Components Replacing the CCD Unit CN1 CN2 Removal Removing the Front Assembly Removing the CC Filter Knob DVW-790WS/790WSP/709WS/709WSP Removing the ND Filter KnobRemoving the CCD Unit DVW-790WS/790WSP/709WS/709WSP Reinstalling the ND Filter Knob Reinstallation Reinstalling the CCD UnitDVW-790WS/709WS DVW-707 Electrical Alignment Reinstalling the Front AssemblyAdjustment After Replacement Tape Running Adjustment CN3 ReinstallationAdjustment After Replacement Replacing the Boards Inside the CCD Unit CN3 CN1 CN6 CN5 CN2CN7 CN4 790WS/790WSP Removing the Connector Box Assembly Replacing the External Connectors/SwitchesCH2, DC IN, DC OUT Connectors Removing the RM-180 Board Removing the CNB-11 BoardRemoving the CNB Stay Audio IN/AUDIO OUT connector Removing the ConnectorDC in connector DC OUT connector VF Connector MIC in Connector Power Switch, MIC in ConnectorPower Switch Shutter Switch Replacing the Rotary Encoder Upper DC Fan Replacing the DC Fans Lower DC Fan Replacing the Camera SW Ornamental Plate CP-329 board Camera SW ornamental plate Mm or less Inside panel Removal Required tool Reinstallation Required tool Replacing the Card Door AssemblyReplacing the 40-pin Fitting Assembly About Tools General Information for Parts Replacement and AdjustmentAbout Cleaning Blade Tape Cleaner depending on model Threading End Mode Threading End/Unthreading End ModeUnthreading End Mode Selection Procedure into the Unthreading End Mode Installation Manual Eject Assembly Removal/Installation Part Name Section Index About stop washer About screwdriver and torque reading About oil and grease Overviews Upper Drum Assembly Replacement Tools Basic informationPreparations Removal Brush Cover Removal Brush Assembly Removal Upper Drum Assembly Removal Desoldering the Leads of Slip Ring Assembly Installation Cleaning of Contact Surfaces Upper Drum Assembly Installation Upper Drum Eccentricity Adjustment Tool Installation Upper Drum Eccentricity Adjustment Tool Removal Upper Drum Eccentricity Adjustment Brush Assembly Installation Soldering the Leads of Slip Ring AssemblyBrush Cover Installation Cleaning of Video Heads and Tape Running Surfaces Video Tracking Adjustment Adjustments After Replacement Tape Running AdjustmentCTL Head Height Adjustment CTL Head Position Adjustment Brush Assembly Replacement for Slip Ring 2x2 Brush assembly Brush cover Connector Installation Brush Assembly Installation Slip Ring Assembly Replacement Remove this screw first Blue Slip Ring Assembly RemovalInstallation Slip Ring Assembly Installation Brush Assembly Installation Drum Assembly Replacement Disconnection of the Brush Assembly Connector Removal Video Head Cleaner Removal CN2 CN3 Drum Assembly Removal Cleaning Drum assembly Positioning pins Connection of the Brush Assembly Connector Drum Assembly InstallationVideo Head Cleaner Installation Cleaning of Video Heads and Tape Running Surface Video System Adjustment CUE Head Height Adjustment Pinch Roller Replacement Pinch Roller Installation Installation Install Shaft CleaningPinch Roller Cleaning Removal Pinch Roller Removal HC Roller Assembly Replacement for Video Heads VH Cleaner Assembly Removal Removal Mode Selection Operation Ceck Installation HC Roller ReplacementVH Cleaner Assembly Installation Manual Eject Assembly Removal CUE Brush Replacement for CUE Head Operation Check Installation CUE Brush ReplacementManual Eject Assembly Installation Brake Band Assembly Replacement Removal Band Holder Removal Brake Band Assembly Removal Brake Band Assembly Installation Installation Reel Table Cleaning FWD Back Tension Adjustment Band Holder Installation Adjustment after replacement Soft Brake Assembly Replacement Removal Soft Brake Assembly Removal Adjustment After Replacement Brake Torque Check Soft Brake Assembly Installation 10. S/T Idler Assembly Replacement Or T Idler Assembly Installation Or T Idler Assembly RemovalInstallation Cleaning of the Installation Shaft 4x2.5 Swing Gear Assembly Replacement Removal Removal of the Swing Gear Assembly Fixing Screw Mechanical Deck Assembly Removal Installation Swing Gear Assembly Installation Swing Gear Assembly Removal Mechanical Deck Assembly Installation Adjustment After Replacement Belt Tension Adjustment Swing Gear Assembly Fixation Timing Belt Replacement Removal Mechanical Deck Assembly Removal Timing Belt Removal Installation Cleaning of the PulleysTiming Belt Installation HN hole Capstan Motor Replacement Removal Manual Eject Assembly Removal Capstan Motor Removal Installation Capstan Motor Installation With drop-safe Pin of the chassis Adjustments After Replacement Belt Tension Adjustment CTL Head Replacement Removal Entrance Head Assembly Removal Entrance Head Assembly Cleaning Installation CTL Head ReplacementEntrance Head Assembly Installation Adjustments After Replacement Tape Running Adjustment CUE Head Replacement Cassette Compartment Removal Gear Block Assembly Removal CUE Head Block Assembly Removal Installation CUE Head Replacement CUE Head Block Installation Gear Block AssembIy InstaIIation Cleaning of the HeadCassette Compartment Installation Audio System Adjustment Video Tracking Adjustmen Reel Table Replacement Reel table removal Removal Reel Table Removal S reel table removal Reel Table Height Adjustment Installation Reel Shaft CleaningReel Table Installation Put the remaining poly washer s in the step Adjustments After Replacement FWD Back Tension Adjustment Pinch Arm Assembly Replacement Removal Pinch Arm Assembly Removal Applying Oil to Installing Shafts Installation Installing Shafts Cleaning Pinch Eoller Cleaning Pinch Arm Assembly Installation Removal Sensor Cover a Removal Sensor a Detection Pin Replacement Sensor Cover a Installation Installation Detection Pins Installation Removal Sensor Cover B Removal Sensor B Detection Pin Replacement Sensor Cover B Installation Tension Regulator Arm Assembly Replacement Removal Brake Band Removal Tension Regulator Arm Assembly Removal Tension Regulator S4 Guide Cleaning Installation Tension Regulator Arm Assembly InstallationBrake Band Installation Overviews Preparations Removal Cassette Guide Removal Disconnection Brush Assembly Connector Catcher S Removal Drawing Arm RemovalDriving Gear Removal Threading Link Assembly Removal Slider Threading base Threading gear assembly installation Parts Replacement Threading Link Assembly Installation Catcher S Installation Drawing Arm Installation Driving Gear Installation 100 Cleaning of the Head and the Tape Running Surface Connection the Brush Assembly ConnectorCassette Guide Installation Replacement of Loading Motor Motor Removal Pinion Gear Removal Installation Pinion Gear Installation Gear Block Assembly Installation Motor Installation Replacement of FE Head 108 Remove the one screw and remove the FE head FE Head Removal BLK GRY Harness RemovalHarness Soldering Installation FE Head Installation Installation Tape Cleaner Installation Replacement of Tape CleanerTape Cleaner Removal Tape Guide Removal Replacement of Tape Guide 114 Installation Tape Guide Installation 115 Adjustment After Replacement Tape Guide Height Adjustment 116 Attaching the Mechanical Deck Mechanical Deck ReplacementRemoving the Mechanical Deck Tension Regulator Operating Position Adjustment Mechanical Adjustment Check Mode Selection Point for adjustment Adjustment Position AdjustmentMode Cancel Tension Regulator Operating Position Check Tool FWD Back Tension Adjustment Adjustment Eject Mode Setting Check REC Mode SettingBack Tension Adjustment Reference of adjustment Brake Torque Check Case that the value does not meet the specification Check SettingAdjustment Mode Cancel Side Brake Torque Check Adjustment Belt Tension Adjustment Belt Tension AdjustmentPage Index Location of Tape Path System Contents Checks Play Mode Playing back the tape top Tape Running AdjustmentSpecifications Drum Entrance Side Threading End Mode Play Mode Playback at tape end FWD Mode Fast forward at tape topREW Mode Rewind at tape top REW Mode Rewind at tape end REV Mode Rewind at tape endFWD Mode Fast forward at tape end Tape Running Re-check at the Drum Entrance Side Checks After Adjustment Video Tracking CheckTape Running Check at the Drum Exit Side CTL Head Height Check Drum Exit Side Checks Play Mode Playing back the tape top REV Mode Rewind at tape end Tape Running Check Around the Capstan Shaft Reference for adjustment Adjustments T2 and T3 Guides Height AdjustmentCUE Head Azimuth Adjustment Tape Running Re-check at the Drum Exit Side Video Tracking Adjustment RF Waveform Check Checks Play ModePlay Mode REV search mode Tape Running Check Drum exit side Tracking Adjustment Drum Exit SideVideo Tracking Re-check CUE Head Height Check CTL Head Height Adjustment Checks Play Back If the Level Increases When Pushing Up the TapeAdjustments After Adjustment CTL Head Position Adjustment CTL Head Position Adjustment CTL Head Position Re-check Adjustments CTL Head Position AdjustmentAdjustment After Adjustment CUE/TC Head Position Adjustment CUE Head Height Adjustment Play back ZR2-1/P from 00 minute to 15 minute segment CUE Head Head-to-contact Check Adjustments CUE Head Height Adjustments CUE Head Azimuth Check CUE Head Azimuth Check CUE Head Head-to-tape Contact Adjustment CUE Head Head-to-tape Contact Adjustment CUE Head Head-to-tape Contact Re- check Adjustments CUE Head Head-to-tape Contact AdjustmentCUE Head Head-to-tape Contact Check CUE/TC Head Position Adjustment Adjustment Adjustments Play BackCUE/TC Head Position Re-check SV REF CF Re-check according to the steps 1 Check CUE Output Level Check CUE Output Level Check Preparation Battery End Detection Voltage Adjustment Power System AdjustmentAdjustment Procedure Check Procedure Setting upon Completion of Adjustment Servo System AdjustmentAutomatic Servo Adjustment Manual PG Phase Adjustment Automatic PG Phase Adjustment GND Audio System Adjustment1. D/A Level Adjustment AGC Level Adjustment Output Limiter Adjustment CUE Recording Bias Adjustment CUE Playback Level Adjustment CUE Recording Level Adjustment Preparation Video System Adjustment Confirmation Procedure Playback Equalizer Automatic Adjustment Precaution Recording Current Automatic AdjustmentPage Initial Switch Settings General Information for Electrical AdjustmentScreen Mode Setting Equipment/Fixtures Initial Setting Handling precautions Maintaining the Grayscale ChartReplacement period when the chart is used as the reference Murakami Color Research Laboratory Setting Illumination when the reflective chart is used Test OUT → ENC VCO Cont Frequency CheckINT SC Frequency Video GEN OUT Lock AD Clock Phase AD Clock Phase AdjustmentClock Phase IRE Ntsc ENC Level Adjustment ENC OUT Adjustment Chroma Adjustment SC Phase INT SC Phase AdjustmentSetting After Adjustment Blanking Width RGB Setup Test OUT Level AdjustmentRGB Sync RGB Level → CAM/ON Modulator Balance Adjustment Test SAW Adjustment Knee → OFF R/B AD Gain AdjustmentAD Gain Test SAW → OFF Gamma Gamma → on VA Gain AdjustmentS35*PRESET WHT Color Temp P Black Shading Adjustment Preset White AdjustmentShading Adjustment S32 *W-SHADING B White Shading AdjustmentS30 *W-SHADING G Test SAW → OFF Gamma Correction AdjustmentMaster Gamma Setting After Aadjustment Black Set Adjustment Flare Flare Adjustment Manual Knee and White Clip Adjustments Knee and White Clip Adjustments Preknee DCC DCC Pre Knee AdjustmentGamma → OFF Test SAW DCC D Range DCC Knee AdjustmentDCC Point → Level Depandent Adjustment Detail Signal AdjustmentCrispening Adjustment Ratio Detail Frequency Adjustment16-4. H/V Ratio Adjustment Knee Aperture Adjustment Detail Level AdjustmentKnee APT APT.LVL Detail Black Clip Adjustment 169/43 Mode → Select the 43 mode 17-4. H/V Ratio Adjustment Detail LVL DTL H B . Clip 43 Factory setting Skin Tone Adjustment Zebra Adjustment Iris Mode Automatic Iris AdjustmentIris Weight → 0 MIN Iris Weight ND Detection → Exec Adjustment After Replacing Filter Disk Unit Lens Initial Setting for SwitchesIris → C Close S06*MASTER Gain Maintaining the Grayscale Chart Setting Illumination when the reflective chart is used GEN SC Lock OUT Video OUT Spec = 40 ± 1 IRE Ntsc = 300 ± 7 mV PAL On the setup menu, adjust as follows S40*ENC ADJ Spec 10.9 ± 0.2 us Ntsc 12.0 ± 0.3 us PAL Spec = 100 ± 2 IRE Ntsc = 700 ± 14 mV PAL Spec = 100 ± 2 IRE Ntsc = 700 ± 10 mV PAL Make sure that the carrier leakage at portion B is not S35*PRESET WHT S50*B-SHADING B Fine WhitepS48*B-SHADING G Para On the setup menu, adjust as follows S25 *LEVEL Spec ± 1 IRE Ntsc ± 7 mV PAL Spec 109 ± 2 IRE Ntsc 763 ± 14 mV PAL Spec ± 2 IRE Ntsc DCC Knee Adjustment Reduce the noise at gray portion to a 16-4. H/V Ratio Adjustment Detail Level Adjustment On the setup menu, set as follows S12*FUNCTION 1/2 Component in the saturation detection ZEBRA1 APT. LVL → 1 % Adjustment Procefure Adjustment After Replacing Filter Disk Unit DVW-790WS/709WS/707 DVW-790WSP/709WSP/707P P2V1 Sony Corporation