3.SCREW TORQUE LIST
Tightening Note:
When tightening any of the screws shaded in the table below, slowly turn it counterclockwise (in the direction to loosen the screw) with your hand until you feel that the screw is a little dropped in the hole. Then, slightly turn it clockwise (in the direction to tighten the screw) with your hand and tighten it according to the specified torque with a screwdriver.
Note:
For verifying the shape of each screw, refer to “APPENDIX 4 SCREW CATALOGUE”.
Location of screw |
| Screw type |
| Q'ty |
| Tightening torque | |||
|
|
| N m (kgf • cm) | ||||||
|
|
|
|
|
|
|
| ||
Tray cover ASSY | Taptite, bind B M4x12 | 2 |
| 0.80 ±0.1 (8 ±1) | |||||
Fuser unit |
| Taptite, pan (washer) B |
|
| 2 |
|
| ± | ± |
| M4x14 |
|
|
|
| 1.20 0.1 (12 | 1) | ||
|
|
|
|
|
|
|
|
| |
Back cover upper | Taptite, cup S M3x8 | 2 |
| 0.80 ±0.1 (8 ±1) | |||||
Drive shaft holder |
| Taptite, bind B M3x10 | 1 |
| 0.60 ±0.1 (6 ±1) | ||||
Paper eject ASSY DX |
| Taptite, cup B M4x12 |
|
| 2 |
|
| 1.20 ±0.1 (12 ±1) | |
|
| Taptite, cup S M3x6 | 1 |
| 0.80 ±0.1 (8 ±1) | ||||
Back cover ASSY | Taptite, cup S M3x8 | 2 |
| 0.80 ±0.1 (8 ±1) | |||||
Transfer HVPS PCB unit |
| Taptite, cup S M3x6 | 2 |
| 0.80 ±0.1 (8 ±1) | ||||
Earth plate 3 | Taptite, bind B M3x8 | 1 |
| 0.60 ±0.1 (6 ±1) | |||||
Density shield plate 1 |
| Taptite, bind B M3x8 | 2 |
| 0.60 ±0.1 (6 ±1) | ||||
Earth plate 2 | Taptite, cup S M3x6 | 1 |
| 0.80 ±0.1 (8 ±1) | |||||
| Taptite, bind B M3x8 | 1 |
| 0.60 ±0.1 (6 ±1) | |||||
| Taptite, bind B M3x8 | 1 |
| 0.60 ±0.1 (6 ±1) | |||||
Density sensor |
| Taptite, bind B M3x8 | 2 |
| 0.60 ±0.1 (6 ±1) | ||||
Registration relay PCB ASSY | Taptite, bind B M3x8 | 1 |
| 0.60 ±0.1 (6 ±1) | |||||
Transfer HVPS PCB ASSY |
| Taptite, cup B M3x10 | 3 |
| 0.50 ±0.1 (5 ±1) | ||||
|
| Taptite, cup S M3x6 | 1 |
| 0.80 ±0.1 (8 ±1) | ||||
Side cover L ASSY |
| Taptite, cup B M4x12 |
|
| 3 |
|
| 1.20 ±0.1 (12 ±1) | |
|
| Taptite, cup S M3x8 | 1 |
| 0.80 ±0.1 (8 ±1) | ||||
Side plate LB |
| Taptite, cup B M4x12 |
|
| 1 |
|
| 1.20 ±0.1 (12 ±1) | |
|
| Taptite, cup S M4x8 | 1 |
| 1.20 ±0.1 (12 ±1) | ||||
|
| Taptite, cup S M3x6 | 3 |
| 0.80 ±0.1 (8 ±1) | ||||
Side cover R ASSY |
| Taptite, cup B M4x12 |
|
| 2 |
|
| 1.20 ±0.1 (12 ±1) | |
|
| Taptite, cup S M4x8 | 2 |
| 1.20 ±0.1 (12 ±1) | ||||
FG harness ADF |
| Taptite, cup S M3x6 | 1 |
| 0.80 ±0.1 (8 ±1) | ||||
FG harness FB |
| Taptite, cup S M3x6 | 1 |
| 0.80 ±0.1 (8 ±1) | ||||
Driver PCB ASSY | Taptite, cup S M3x6 | 2 |
| 0.80 ±0.1 (8 ±1) | |||||
Hinge protection cover ASSY | Taptite, cup B M4x12 | 3 |
| 0.80 ±0.1 (8 ±1) | |||||
Hinge |
| Taptite, bind B M4x12 | 2 |
| 0.80 ±0.1 (8 ±1) | ||||
Hinge base R |
| Taptite, bind B M4x12 | 1 |
| 0.80 ±0.1 (8 ±1) | ||||
|
| Taptite, cup B M3x10 | 3 |
| 0.50 ±0.1 (5 ±1) | ||||
Hinge ASSY L |
| Taptite, bind B M4x12 | 1 |
| 0.80 ±0.1 (8 ±1) | ||||
|
| Taptite, cup B M3x10 | 3 |
| 0.50 ±0.1 (5 ±1) | ||||
Confidential |