Pcmcia Memory Expansion, REAL-TIME Clock | SATO 10e specification

Section 4: Accessories Installation

NOTE: The wiring harness connectors and their mates on the main cicuit board are unique to all others on the board. Properly couple the matching connectors. Refer to Figure 10-4, Block Diagram of the Diagram & Schematics section for greater detail if necessary.

11 Configure the printer for cutter accessory operation.

NOTE: Refer to the Configuration section of this manual or the Programming

Manual for label cutter configuartion instructions.

12Apply media stock and ribbon as applicable and test cycle to ensure proper function.

13Install the left, right, front, and top housing covers.

NOTE: Figure 10-1 in the Diagrams & Schematics section provides guidance on housing cover removal.

PCMCIA MEMORY EXPANSION

The PCMCIA Memory Card comes packaged with installation instructions. Mating connectors on the memory card and interface board make hardware installation very simple. When installation is complete, perform a memory self-test to ensure the memory card is recognized.

NOTE: Refer to the Interface Board procedure in the Replacement section of this manual for instructions on its removal. Connect the memory expansion card to the interface board and reinstall.

REAL-TIME CLOCK

The real-time clock chip allows the date and time to be maintained in the local printer rather than using the system clock. It consists of a special clock chip that replaces the EEPROM chip on the main circuit board.

1Switch the printer off and disconnect the power supply cord.

2Remove the top, front, and left housing covers to gain access to the main circuit board.

NOTE: Figure 10-1 of the Diagrams & Schematics section provides guidance on housing cover removal.

3 Locate and withdraw the EEPROM chip (1, Figure 4-2) from main circuit board (2).

CAUTION: IF USING A TOOL TO REMOVE THE EEPROM CHIP, ENSURE

THAT IT IS NOT BEING INSERTED BETWEEN THE IC SOCKET AND THE

CIRCUIT BOARD. DESTRUCTION IN THE CIRCUIT BOARD WILL

OCCUR. INSERT THE TOOL BETWEEN THE TWO PIECES OF BLACK

PHENOLIC MATERIAL TO PRY THE CHIP FREE.

SATO M10e Service Manual

PN 9001113A

Page 4-3

Image 27

SATO 10e service manual Pcmcia Memory Expansion, REAL-TIME Clock

Contents

M10e Thermal Transfer Printer Page Table of Contents Troubleshooting Factory Resets PN 9001113A Result in Presonal Injury Introduction Theory of Operation General Description Correct signals initiates print head activity DIP Switches Switches and IndicatorsSwitches Indicators Configuration Panel Connection Ports Connection Ports Print Physical CharacteristicsPower Environmental Character Font Capabilities Downlaodable Fonts Auto Smoothing FontsVector Font Agfa Raster Fonts Regulatory Approvals BAR Code Capabilties Receive Buffer Interface Types IEEE1284 Parallel Interface Init Specifications RS232C Serial Interface Signals Direction Signal DefinitionRS232 Serial Interface Cable Requirements DB9 HostPrinter Local Area Network LAN Optional Interface Universal Serial BUS USB Interface Stream Identification Cancel canBI-DIRECTIONAL Communications ENQUIRE/ACK/NAK Print JOB Label Cutter Installation Accessories Installation 1b, Cutter Installation REAL-TIME Clock Pcmcia Memory Expansion Insert clock chip 3 into the vacant IC Socket Interface Module Upgrade Stacker KITMedia Unwind Unit Accessories Installation PN 9001113A DIP Switch Panels RS232 TRANSMIT/RECEIVE SettingOFF DSW1-4 DSW2 OFF Printer SET UP DSW2-5 DSW3 OFF Setting DSW3 Setting Software Default Settings Default SettingsSoftware Default Settings Default Settings Potentiometer Adjustments LCD Panel Configuration Normal Mode Configuration Modes LCD Display Definition Advanced Mode Print Offset SET CalendarCalendar Card Mode Copying Xxxxxxx ErrorCard COPY/FORMAT Sato Font Copy Program CARD-MEMORYCOPY Service Mode Setting the threshold is Reprint W/FEED Feed on ErrorEYE XXV Auto Online Feed EXT PIN 9 Select Priority SettingCommand LCD Enable Disable Counters Mode Default Settings Mode Test Print Mode ALL Clear Mode MAINTENANCE/FACTORY Mode Download User Defined Protocol Codes Clear NON-STANDARD Protocol QTY000000 HEX Dump Mode Error LED LCD Message Beep Resolution Guide Error Signals Light Print Image Troubleshooting TableImage Voids Ribbon Wrinkling No Label Movement Power LED not IlluminatedFuzzy Print Image No Ribbon Movement Ribbon LED Illuminated Error LED IlluminatedWill not Print When Data is Sent Label LED is Illuminated Universal Serial BUS USB Interface Troubleshooting RS232 Serial Interface Troubleshooting Parallel Interface Troubleshooting LAN Ethernet Interface Troubleshooting TCP/IP Troubleshooting Netware Troubleshooting Windows NT/LAN Server Troubleshooting Diagnostic Label Printing Windows 95/98 PEER-TO-PEER Troubleshooting Dial Application Description TP Test Module Usage TP Test Module Usage Ribbon Sensor Operation Verification LCD Display Test Print Mode Configuration Print Head Replacement Replacement Procedures Roller Belt Replacement Roller Belt Replacement Ribbon Belt Replacement Ribbon Belt Replacement Platen Roller Replacement Platen Roller Replacement Feed Roller Replacement Feed Roller Replacement Main Circuit Board Replacement Circuit Board Replacement Interface Board Replacement Interface Board Replacement Ribbon Drive Board Replacement 8b, Ribbon Drive Board Replacement Panel Board Replacement Memory Card Replacement Panel Board Replacement Power Supply Replacement 10, Power Board Replacement 11, Fuse Replacement Power Supply Fuse Replacement 12, Fuse Replacement Circuit Board Fuse Replacement 13, Fuse Replacement Drive Motor Replacement Ribbon Motor Replacement 14, Ribbon Motor Replacement 15, Auto-Load Sensor Replacement AUTO-LOAD Sensor Replacement Label Position Sensor Replacement LABEL-OUT Sensor Replacement 16, Label Gap Sensor Replacement 17, Eye-Mark/Label-Out Sensor Replacement Ribbon Sensor Replacement 18, Ribbon Sensor Replacement Cutter Replacement 19, Cutter Assembly Replacement Cutter Sensor Replacement 20, Cutter Sensor Replacement Eeprom Chip Replacement 21, Eeprom Chip Replacement Print Head Position Adjustment Procedures Print Head Alignment Print Head Alignment Adjustment Ribbon Wrinkle Adjustments Ribbon Wrinkle Adjustments Roller Belt Adjustment Roller Belt Adjustment Ribbon Belt Adjustment Ribbon Belt Adjustment Media Guide Adjustment Paper Guide Adjustment Pitch Sensor Adjustment Place the DSW2-4 dip switch in the Off position EYE-MARK Sensor Adjustment Eye-Mark Sensor Adjustments Label GAP Sensor Adjustment Label Gap Sensor Adjustment Auto Load Sensor Adjustment 10, Auto-Load Sensor Adjustment 11, Paper End Sensor Adjustment Paper END Sensor Adjustment Offset Label Stop Position Adjustment Print Darkness Adjustment LCD Display Adjustment Adjustment Procedures PN 9001113A Factory Settings / Test Print Factory Resets Clear Head Counters Press the Enter key to clear the cutter counter Clear Cutter Counter Clear Eeprom LCD Display Xxxxxall Clear Completed Factory Resets PN 9001113A Housing Cover Removal & Installation Diagrams & Schematics Media & Ribbon Loading Media & Ribbon Loading Power Board Block Diagram Printing Operational Sequence Printer Accessories & Sensors Location Accessories & Sensors Location Print Reference Position Feed Direction