HEX Dump Mode, QTY000000 | SATO 10e guide

Section 5: Printer Configuration

HEX DUMP MODE

In addition to the Test Print Labels, the printer can print the contents of the receive buffer in a hexadecimal format to allow the data stream to be examined for errors and troubleshooting.

LCD DISPLAY		DEFINITION

V 05.00.03.00	Displays the firmware during the initialization.
INITIALIZING
ONLINE	The Hex Dump Mode is entered by placing DSW2-4 in the On position and
QTY:000000	powering the printer on.
	1.	The printer is now ready to receive data.
	2.	Send the data stream to the printer.
	3.	The received data will be printed in a hexadecimal format4.
	4.	To return the printer to normal operation, place DSW2-4 in the off position
		and power the printer off and then back on.

SATO M10e Service Manual

PN: 9001113A

Page 5-24

Image 54

SATO 10e service manual HEX Dump Mode, QTY000000

Contents

M10e Thermal Transfer Printer Page Table of Contents Troubleshooting Factory Resets PN 9001113A Introduction Result in Presonal Injury General Description Theory of Operation Correct signals initiates print head activity Indicators Switches and IndicatorsSwitches DIP Switches Configuration Panel Connection Ports Connection Ports Environmental Physical CharacteristicsPower Print Character Font Capabilities Agfa Raster Fonts Auto Smoothing FontsVector Font Downlaodable Fonts BAR Code Capabilties Regulatory Approvals Interface Types Receive Buffer IEEE1284 Parallel Interface Specifications Init RS232C Serial Interface Signals Direction Signal DefinitionRS232 Serial Interface Cable Requirements DB9 HostPrinter Universal Serial BUS USB Interface Local Area Network LAN Optional Interface ENQUIRE/ACK/NAK Cancel canBI-DIRECTIONAL Communications Stream Identification Print JOB Accessories Installation Label Cutter Installation 1b, Cutter Installation Pcmcia Memory Expansion REAL-TIME Clock Insert clock chip 3 into the vacant IC Socket Interface Module Upgrade Stacker KITMedia Unwind Unit Accessories Installation PN 9001113A DIP Switch Panels RS232 TRANSMIT/RECEIVE SettingOFF DSW1-4 Printer SET UP DSW2 OFF DSW2-5 Setting DSW3 DSW3 OFF Setting Default Settings Default SettingsSoftware Default Settings Software Default Settings Potentiometer Adjustments LCD Panel Configuration Configuration Modes Normal Mode Advanced Mode LCD Display Definition Print Offset SET CalendarCalendar Card Mode Sato Font Copy Xxxxxxx ErrorCard COPY/FORMAT Copying CARD-MEMORYCOPY Program Service Mode Setting the threshold is Auto Online Feed Feed on ErrorEYE XXV Reprint W/FEED Enable Disable Priority SettingCommand LCD EXT PIN 9 Select Counters Mode Test Print Mode Default Settings Mode MAINTENANCE/FACTORY Mode ALL Clear Mode Clear NON-STANDARD Protocol Download User Defined Protocol Codes HEX Dump Mode QTY000000 Error Signals Error LED LCD Message Beep Resolution Guide Ribbon Wrinkling Troubleshooting TableImage Voids Light Print Image No Ribbon Movement Power LED not IlluminatedFuzzy Print Image No Label Movement Label LED is Illuminated Error LED IlluminatedWill not Print When Data is Sent Ribbon LED Illuminated RS232 Serial Interface Troubleshooting Universal Serial BUS USB Interface Troubleshooting Parallel Interface Troubleshooting LAN Ethernet Interface Troubleshooting TCP/IP Troubleshooting Netware Troubleshooting Windows NT/LAN Server Troubleshooting Windows 95/98 PEER-TO-PEER Troubleshooting Diagnostic Label Printing TP Test Module Usage Dial Application Description Ribbon Sensor Operation Verification TP Test Module Usage LCD Display Test Print Mode Configuration Replacement Procedures Print Head Replacement Roller Belt Replacement Roller Belt Replacement Ribbon Belt Replacement Platen Roller Replacement Ribbon Belt Replacement Platen Roller Replacement Feed Roller Replacement Feed Roller Replacement Main Circuit Board Replacement Interface Board Replacement Circuit Board Replacement Ribbon Drive Board Replacement Interface Board Replacement 8b, Ribbon Drive Board Replacement Memory Card Replacement Panel Board Replacement Power Supply Replacement Panel Board Replacement 10, Power Board Replacement Power Supply Fuse Replacement 11, Fuse Replacement Circuit Board Fuse Replacement 12, Fuse Replacement Drive Motor Replacement 13, Fuse Replacement Ribbon Motor Replacement 14, Ribbon Motor Replacement AUTO-LOAD Sensor Replacement 15, Auto-Load Sensor Replacement LABEL-OUT Sensor Replacement Label Position Sensor Replacement 16, Label Gap Sensor Replacement 17, Eye-Mark/Label-Out Sensor Replacement Ribbon Sensor Replacement Cutter Replacement 18, Ribbon Sensor Replacement 19, Cutter Assembly Replacement Cutter Sensor Replacement Eeprom Chip Replacement 20, Cutter Sensor Replacement 21, Eeprom Chip Replacement Adjustment Procedures Print Head Position Print Head Alignment Adjustment Print Head Alignment Ribbon Wrinkle Adjustments Ribbon Wrinkle Adjustments Roller Belt Adjustment Roller Belt Adjustment Ribbon Belt Adjustment Ribbon Belt Adjustment Paper Guide Adjustment Media Guide Adjustment Pitch Sensor Adjustment Place the DSW2-4 dip switch in the Off position EYE-MARK Sensor Adjustment Eye-Mark Sensor Adjustments Label GAP Sensor Adjustment Auto Load Sensor Adjustment Label Gap Sensor Adjustment 10, Auto-Load Sensor Adjustment Paper END Sensor Adjustment 11, Paper End Sensor Adjustment Offset Label Stop Position Adjustment LCD Display Adjustment Print Darkness Adjustment Adjustment Procedures PN 9001113A Factory Resets Factory Settings / Test Print Clear Head Counters Clear Cutter Counter Press the Enter key to clear the cutter counter Clear Eeprom LCD Display Xxxxxall Clear Completed Factory Resets PN 9001113A Diagrams & Schematics Housing Cover Removal & Installation Media & Ribbon Loading Media & Ribbon Loading Block Diagram Power Board Printer Printing Operational Sequence Accessories & Sensors Location Accessories & Sensors Location Feed Direction Print Reference Position