Manuals / Avaya / Computer Equipment / Network Router

Avaya CMC1 manual Definity Audix

Models: CMC1

1 370

Download 370 pages 26.18 Kb

Page 61

			Install Equipment Room Hardware
Table 5: Circuit Pack Installation Order (Loading)

Function	Apparatus Code	Load From		Notes

Processor	TN2402	Slot 1 in
		Cabinet A

Tone Clock	TN2182C	Slot 2 in
		Cabinet A

Call Classifier/ Tone	TN744E	Slot 1 of		If slot is not available, load
Detector		Cabinet B		in first available slot from
				slot 1.

DEFINITY AUDIX	ED-1E546 (TN566/	Slots 6-9		TN566 and TN567 require
	TN567)			4 slots with overlap into
				area to the left of slot 6. In
				any other position, 5 slots
				are required.

DEFINITY AUDIX	TN568	Slot 6		TN568 requires 2 slots.
Slim				If there is a fiber-optic
				interface and slot 6 is
				occupied, use slots 7 and
				8.

Announcement	TN750C	Lower Left

Speech Synthesizer	TN725B	Lower Left

DS1/E1, ISDN PRI	TN464HP, TN767E,	Lower Left		Maximum of 8 ISDN-PRI.
	TN2242, TN464CP			Total number of ISDN-PRI
	(Guestworks and			plus number of ISDN-BRI
	BCS only)			circuit packs must not
				exceed 8.

ISDN-BRI Trunk	TN2185B	Lower Left		Maximum of 4

CO Trunk	TN747B, TN465C,	Lower Left
	TN2199, TN2147C,
	TN2138, TN438B

DID Trunk	TN753B, TN2139,	Lower Left
	TN2146, TN436B,
	TN459B

Tie Trunk	TN760E, TN497,	Lower Left
	TN2140B

Auxiliary Trunk	TN763D	Lower Left

Modem Pool	TN758	Lower Left

				1 of 2

Issue 10 June 2005 61

Image 61

Avaya CMC1 manual Definity Audix

Contents

Issue 10 June Copyright 2005, Avaya Inc All Rights Reserved SOC Installation and Repairs About This Book Contents Contents Contents Contents Completing Installation and Cable Pinouts 151 Contents Contents Adding or Removing Hardware 231 Contents Contents Installing a J58890CG Power Contents Appendix B Access Security Gateway 361 Page General Conventions used in this bookTypographic Admonishments Physical dimensions How to get this bookTrademarks On the Web Non-Web Where to get additional help Avaya support Support Number Tell us what you think Remove/Install circuit packs Security IssuesAntistatic Protection Pre-installation checklist Pre-installation checklistRead This First License File Installing and Cabling the Cabinets No direct connection Go to the RFA website Selection If you have problems with RFA Check Customer’s Order Correcting Shipping ErrorsUnpack and Inspect Equipment Packed with the Compact Modular Cabinet Comcodes for CMC1 Description Comcodes for CMC1 Comcodes for CMC1 Description Comcodes for CMC1 Description Set the Carrier Address ID All Cabinets Install the System Cabinets Floor-Mount the Cabinet Typical Floor Mount Installation Single-Cabinet Installation Install Plywood Backing onto WallWall-Mount the Cabinets Or 3 Vertically Mounted Cabinets Left Panel Used as Mounting Template Install Cabinet a Wall-Mount Typical Wall-Mount Installation Typical Vertical Multicabinet Installation Install 2 or 3 Vertically Mounted Cabinets Typical 3-Cabinet Installation Install 2 Cabinets Vertically and 1 Cabinet Horizontally Left and Right Panel Installation Install Left and Right Panels Wall-Mount Check AC Power AC Power and Ground Approved Floor Grounds Approved Grounds Uninterruptible Power Supply CMC Power Supply CMC Power Switch Connect Cabinet Grounds and Other Grounds Install the Ground Block Typical Cabinet Grounding Connect and Route Cabinet AC Power Cords Install Coupled Bonding Conductor Routing AC Power Cords to a Power Distribution Unit System Cable Connections Cable the System Vertically Mounted System Cable the Multi-Cabinet System Wall-Mount Vertically and Horizontally Mounted System Install the MDF Install Main Distribution Frame MDF and External ModemBottom-mounted MDF with Modem Typical Bottom-Mount MDF and Modem Cable Routing Typical Top-Mount MDF Cable Routing Top-Mounted MDF Preliminary Dual-Mount MDF Cable Routing Dual MDFs Typical Dual-Mount MDF Cable Routing Install the External Modem Install Equipment Room HardwareCross-Connect the Cabinets to the MDF Circuit Pack Slot Loading Circuit Pack Installation Control Carrier Slot Layout Definity Audix Installing and Cabling the Cabinets Example MDF Connections Off-Premises Circuit Protection Install Sneak Fuse Panels Model 507B Sneak Fuse Panel Sneak Fuse Connector Pinout Pair/Fuse Pin Numbers Label the Main Distribution Frame Label Graphic Symbols and Nomenclature Connecting a PC Set Up System AccessStarting Terminal Emulation Remote connection Direct connection Figure notes Connecting through a data module Adding a data module Data module settingsType add data-module number or add data-module next Setting the operating mode Testing hardware connectionsType How to Test and Troubleshoot Data Module Type How to set the operating mode Data Module Setting the 7400B+ optionsDIP Switch Settings 7400B+ Option Data Terminal Ready override Connecting by analog modemVerbal result codes Numeric result codes No echo, offline commands S. Robotics Modem Dip Switch Settings DescriptionLoad factory defaults Smart mode Ringing Option Selection Set Ringing Option Power Up System Activate and Administer the SystemDeliver or Install the License File Single Cabinet Installations Log into the System System AdministrationCheck System Status Check Customer Options System Parameters COUNTRY-OPTIONS Set Country OptionsTone Detection Parameters USA Country Codes Password Administration Change Craft PasswordLogin Being Changed LOGIN’S Password Information Type change daylight-savings-rules and press Enter Set Daylight Savings RulesDaylight Savings Rules English Day of the Week Names Day Name Number Set Date and TimeDate and Time Time English Month Names Number Set System Maintenance Parameters Circuit Pack AdministrationAdminister the Attendant Console Enter change system-parameters maintenance and press Enter Save Translations Install and Wire Telephones and TrunksAdd Translations DCP, analog, and ISDN-BRI 302D to Digital Line Circuit Pack Wiring Analog Tie Trunk Example Analog Station or 2-Wire Digital Station Example Digital Tie Trunk Example Digital Tie Trunk Wiring DS1 Tie Trunk Example Pinout of C6F Cable Wire Color Lead Designation Pin NumberCollocated DS1 Tie Trunks Pair and 4-Pair Modularity DS1 Tie Trunks Using T1 Channel Service Unit Hard-Wire Bridging Install Attendant Console Optional Install 26B1 Selector Console Optional Install and Wire Telephone Power SuppliesAdminister IP Stations and Trunks Dual Wiring of 2-Wire and 4-Wire Endpoints Adjunct Power Adapter Typical Adjunct Power ConnectionsAdjunct Power Connections End-to-End Example Adjunct Power Connections Auxiliary Power for an Attendant Console Local and Phantom Power 1145B2 Power Supply Important Warning for 1145B2 Power Supply Mounting the 1145B2/1146B2 Power Supply 1145B2/1146B2 Mounting Arrangement Expanded Power Distribution Unit Mount the 1146B2 Power Distribution Unit Install the Wall-Mounting Plates Install the Expanded Power Distribution Unit Install the Battery Mounting/WiringBack-Up Battery Rating Power Supply LEDs LED Color Meaning Power Up and Test the Power Supply Wire the 1146B2 Power Distribution Unit Typical Wiring to a Telephone Reset LEDs on Power Distribution Unit 1152A1 Mid-Span Power Distribution UnitImportant Safety Instructions 1152A1 PDU UL 1950 Compliance Complies Using the 1152A1 PDU Connect the Cables Connect the 1152A1 PDU Connecting an IP telephone with an external splitter Connecting cables to telephones and other end devices P333T-PWR switch Important Safety Instructions P333T-PWR Power over Ethernet Stackable SwitchP333T-PWR UL 1950 Compliance Complies Connect the P333T-PWR switch Using the P333T-PWR switchPower up-AC input Connect the Cables Power up-DC input optional 1151B1 and 1151B2 Power Supply UL 60950 Compliance Complies 1151B1 and 1151B2 Power SuppliesCSA Connect the 1151B1 or 1151B2 Power Supplies Using 1151B1 and 1151B2 Power Supplies Alarm Input Connect External Alarms and Auxiliary ConnectionsAlarm Inputs at AUX Connector Color Type Emergency Transfer and Auxiliary Power Alarm OutputAlarm Output at AUX Connector Color Type GRD Telephone Pin Designations Configuration CAMA/E911 InstallationHardware Setup Administration Setup Trunk Group Trunk Group Administrable TimersTAC Trunk Parameters Group Member Assignments Group Member Assignments form Feature Access Code FAC Feature Access Code FAC form ANI ARS Digit Analysis Table BCC Value TSC CA-TSC IXC Route Pattern form Cesid Cama Numbering E911 Format Type Save Translation and press Enter Install the BRI Terminating ResistorClass of Restriction FRL Wide Terminating Resistor Adapter 440A4 Terminating Resistor Adapter Terminating Resistor Block 110RA1-12 Closet Mounted 110RA1-12 Typical Installation of Terminating Resistor Block Install Multi-point Adapters BR851-B Adapter T-Adapter Wiring Diagram of BR851-B 367A Adapter Wiring Diagram of 367A Adapter Basic Multi-point with One Work Location Basic Multi-point Installation Distances Install Off-Premises or Out-of-Building Stations Install Off-Premises Station WiringAnalog Off-Premises Stations Connections for 1 to 8 Out-of-Building Analog Telephones Connections to 24 Out-of-Building Telephones Circuit Protectors Digital Out-of-Building Telephones Install Off-Premises Station Wiring Install the Emergency Transfer Panel Install Emergency Transfer Unit Associated Telephones 808A Emergency Transfer Panel Trunk/Test Switches Circuit Number TTC1 RTC4 Connections for Telephone Used for Emergency Transfer Install Telephone for Power Transfer Unit Telephone Installation Connect Modem to Telephone Network Pinout of Network Jack Pin Number Signal Echo offline commands External Modem Option SettingsLoad Nvram defaults Carrier detect normal Modem Fields Description Turns on the V.42 Lapm and MNP error control protocols. Page Alarms and Reporting System AdministrationResolve Alarms Register the Switch for Maintenance Enable Alarm Origination to InadsExternal Modem Installed Type change system-parameters maintenance and press Enter Alarms and Reporting Click on the Start Product Registration button Alarms and Reporting Set Neon Voltage Ring Ping Place a Test Call Power Supply LED Indications Installation CompletionLED and Alarm Conditions Alarm Fan Alarm Status State Signaling Formats for TN760E Mode Type TN760E Tie Trunk Option Settings TN760E Tie Trunk Circuit Pack Component Side TN760E Option Switch Settings and Administration Option Switch Settings on TN464HP and TN464CP TN464HP and TN2464CP Option Settings TN464HP and TN2464CP Option Settings BK-BL Connector and Cable Diagrams Pinout Charts BL-BK BR-V Name Amphenol Connector Processor Interface Cable Pinout SignalProcessor Interface Cable Pinout Port Circuit Pack Lead Designations Modem Name Amphenol TXR.2 LI High \BR TXR.4 BL-W SL/V DIOD2 Circuit Pack and Auxiliary Equipment Classifications Digital Analog Line Wire Ports Circuit Pack and Auxiliary Equipment Leads Pinout Charts Four Pin Line Digital Trunk Trk LI, LI Read This First Digit dial plan expansion Service InterruptionCall Management System Contact Network Technicians Software Upgrade Translation Card Upgrade ProceduresUsable Circuit Packs Tasks List Task Table Tasks List Task Description Pre-upgrade checklist To the RFA Website Pre-upgrade administration changes Have direct connection Rk.com Remove Print Messages Feature Access Code Pre-upgrade administration changesPre-upgrade administration changes Isdn Remove print-msgs buttons Abbreviated Dialing Station Site DataButton Assignments Attendant Console Remove MSA processor channels Remove MSA node namesAUDIX-MSA Node Names Processor Channel Assignment Check SPE Remove MET station administrationVerify Software Version Verify System Status Disable Scheduled Maintenance and Alarm Origination to Inads Save Translations Check Link Status Shut Down Definity Audix System if necessary Save Announcements if necessaryReplace Circuit Packs Pre-installation Install the License FileType reset system 3 and press Enter Installation direct connection Display Memory-ConfigurationInstallation no direct connection Set Daylight Savings Rules Enable Scheduled Maintenance Verify the UpgradeType display alarms and press Enter List trunk-group list hunt-group list data-module Enable Alarm Origination to Inads Click on the Start Product Registration button This verification might be done automatically in the future Page Restore Announcements if necessary Power Up Definity Audix SystemCheck Customer Options Type display communication-interface links and press Enter Save Translations post-upgrade Install translation cardSave Announcements if necessary- post-upgrade Return Equipment Power Down the Audix System Definity Audix Power ProceduresPower Up the Audix System Type reset system shutdown and press EnterPage On an Avaya Definity Server CSI Software compatibility Call Management System CMS Antistatic protection Wireless systems Task Description Configuration license long SAT command Pre-upgrade checklist RFA website Pre-upgrade administration changes Go to the RFA website GSO Pre-upgrade administration changes Remove Print Messages Feature Access Code Station form Remove MSA node names Remove MET station administration Type status system 1 and press Return Verify version Type display errors and press Return Disable scheduled maintenance and alarm originationType change system-parameters maintenance and press Return Enter display communication-interface links and press Return Upgrade the software Install the License File Administer no-license/emergency numbers Type change daylight-savings-rules and press Return Type display alarms and press Return Type display communication-links and press Return Type list signaling-group press Return Enable scheduled maintenance Click on the Start Product Registration button This verification might be done automatically in the future Restore busyouts Save announcements post-upgrade Restore announcements Add Circuit Packs Upgrade Firmware on Programmable Circuit PacksType change circuit-pack VAL Self and C-LAN-distributed download procedure TN771DP Download Method Differences LAN-distributed Prepare for downloadDownload Self download DIG-LINE Verify hardware/software requirements Type list fiber-link and press Enter Type add data-module UUC17 and press Enter Get circuit pack informationType add data-module UUC33 and press Enter Upload image file from the Web to staging area Set up source circuit pack’s file system Schedule a download to targets FTP the image file to sourceType change firmware download and press Enter Disable firmware download Directory board command showedFirmware Download fields and descriptions Field Description Firmware download or a status Automatically remove the new Download, the procedure Firmware Download Monitor download progress Status Firmware Download Reseat VAL circuit pack Disable file systemType list directory board Uucss and press Enter Testing firmware download Troubleshooting firmware downloadsAborting a firmware download Reverting to an older TN799DP or TN2501AP vintage Backing out of a firmware downloadDisplay Firmware Images Adding or Removing Hardware Install TN464HP/TN2464CP with Echo Cancellation Type add change trunk-group next number and press Enter Trunk Features DS1 Circuit Pack Type add change ds1 Uucss and press EnterCAS Add CO, FX, WATS, and Pcol InstallationRequirements Add Tie Trunks Add did Trunks Tie Trunk Circuit Packs Component Side Add DS1 Tie and OPS Tie Trunk Option-Switch Settings and Administration Add Speech Synthesis Add Code Calling AccessAdd Pooled Modem Type add data-module next and press Enter Settings for Modem Connected to Data ModuleType add station next and press Enter Type add modem-pool next and press Enter Replacing a TN750/B/C circuit pack Add Integrated Announcements/TN2501AP Configurations Announcement File SpecificationsCaveats Before you start Recording and storing announcements Hardware specificationsFTP client application VAL Manager application PC only LAN cable Backplane AdapterMbps uses Category 3 cable Mbps uses Category 5 cable Hardware installation Switch administration before hardware installation List configuration board Administer the IP connections Change ip-interfaces Change node-names ipSPE a IP Node Names VAL#1 LAN IP InterfacesMedpro VAL Add ip-route Add data-moduleData Module Test the IP connections Add ISDN-PRINorth American International Add Circuit Packs Install CablesEnter Added Translations Install Circuit Packs Disable Alarm OriginationAdd Packet Bus Support Test the Packet Bus and C-LAN Circuit Pack Administer the Bus BridgeVerify Customer Options Add CallVisor Asai Enable Asai option Install cables from TN464HP to the MDF as required Add TTC Japanese 2-Mbit Trunks Installing the trunkAdd DCS Interface Test the Packet Bus and Control-LAN Circuit Pack Cable Connection for C-LAN Add the Packet Bus Support Add ISDN-BRI Add ISDN-BRI Add Radio Controller Add IP SolutionsAdd IP Media Processor Check your onsite equipment Preparing for Installation and Upgrade Required Hardware Check your shipment Connect the cables for TN799DP Installing the TN2302AP IP Media Processor Connect the cables for TN2302AP Install the Circuit PacksConnect the Ethernet TN2302AP IP Interface faceplate Type change node-names and press Enter Initial Administration Steps for C-LAN IP Media ProcessorNode Names Type change ip-interfaces and press Enter Ping Results Test the External Connection to the LANMedpro Pass Upgrading TN802 IP Trunking to TN2302AP IP Media Processor Pre-upgrade stepsRemove the Circuit Packs Replace the Cables Administration Medpro Remove the Circuit Packs Install the circuit packs Checking for required components Installing an Integrated Channel Service Unit Icsu Module 120A3A Channel Service Unit Module Installing the 120A3A CSU Adding or Removing Hardware H600-383 Cable Lengths by Group Number Mounting without a backing plate Installing a J58890CG Power Distribution UnitMounting with a backing plate Installing and administering the terminal server Install terminal serverRequired equipment Comcode Description Qty Supplier Distance limits Making the connections Cabling diagram Connecting an adjunct to the IOLAN+ Setting up HyperTerminal on the computer Administering the IOLAN+Navigating the IOLAN+ terminal server Connections Menu Administering the IOLAN+ the first timeCLI Administration Menu Select Admin mode Password and press Enter Subnet mask Server Configuration Administering the gateway Rebooting the IOLAN+ Port Setup Menu Administering an IOLAN+ portDestination IP address Term Speed Monitor DSR Yes Monitor DCD No Access Remote Authentication None Mode Raw Connection NoneRemote Port Select Admin mode stats and press Enter twice TestingPotential failure scenarios and repair actions Administering IP services Administering IP node names Session Layer Timers IP ServicesCDR1 Spdu Connecting CDR Equipment Install Call detail recording CDRAdministering CDR Data Collection Local Node field, enter switch-clan Administering CDR parameters Primary Output Endpoint field, type CDR1 Testing the switch-to-adjunct linkCDR System Parameters CDR Link Status Contents of the Rdtt Install Reliable Data Transport Tool Rdtt PackageDownloading the tool Installing Rdtt Install wideband endpointsAdministering Rdtt Nonsignaling configuration Typical nonsignaling wideband configuration Signaling configuration Typical signaling wideband configuration Install multimedia call handling Mmch Connect the endpoints Administer the system Administer the endpoints Expansion services moduleAdminister one number complex Type y in the Multimedia Early Answer field and press Enter ESM installation Administration Place test call Troubleshooting Administering adjunct parameters Connecting printers using TCP/IPConnect printers Task list System printer Testing the switch-to-adjunct linkSystem Printer Endpoint field, type Sysprnt Installing a loopback jack Install DS1/T1 CPE loopback jackWith a smart jack Loopback testing with a smart jack Administering the loopback jackWithout a smart jack Administering the DS1 for the test Testing the DS1 span from the Icsu to the loopback jackChecking the integrity of local equipment Busying out the DS1 circuit pack Testing the integrity of data sent over the loop Testing the integrity of the loopback circuitClearing the results of previous tests Running the data test Install DS1/T1 CPE loopback jack ConditionSolution Condition Solution Releasing the DS1 circuit pack Restoring DS1 administration Network interface at smart jack for a 120A2 or later Icsu Install DS1/T1 CPE loopback jack Testing a loopback jack without a smart jack Network interface at dumb block for a 120A2 or later Icsu Adding or Removing Hardware Configurations using fiber multiplexers Install Isdn converters and adapters PRI-to-DASS and PRI-to-DPNSS converters Converters for single-carrier cabinets Typical PRI to BRI converter cabling PRI-to-BRI converter Converters for multi-carrier cabinets 00221 PDH Typical 909A/B universal coupler Install 909A/B universal coupler BSY2/BY2 Typical modular jack pinout Malicious call trace Install malicious call trace Install music-on-hold Nonregistered music source Registered music source Wiring block must be locally engineered Install paging and announcement equipment Loudspeaker paging without paging adapter Loudspeaker paging Loudspeaker paging access without universal coupler Loudspeaker paging with universal coupler External ringing Espa radio paging Queue warning indicator Other adjunct installation information sourcesIntuity Audix Messaging Systems Asai and Definity LAN Gateway Avaya Modular Messaging SystemAvaya Interactive Response Avaya EC500 Extension to Cellular and Off-PBX Stations Troubleshooting Guidelines Appendix a Troubleshooting an Upgrade No Translation After Upgrade Troubleshooting UpgradesTranslation Corruption Detected Unsuccessful Translation Backup Re-install the ISDN-PRI Links Only for Failed UpgradesSoftware Incompatibility Type add data-module PI ext and press EnterPage Using the ASG Mobile Appendix B Access Security Gateway Access Security Gateway Index Back-up battery backup translations RAM Installing impedance, setting TN2185 ISDN-BRI 113 TN2464BP/CP Wiring telephone power supplies