Station Apparatus

Tilt Stands

Tilt Stand for DKT/IPT + Two ADMs

Use Tilt Stand models “BTSA” for DKTs or IPTs with one or two ADMs.

To attach a Tilt Stand to a 3000-series DKT, IPT1020-SD with two ADMs

1.Complete the steps under “To install DADMs” on page 11-21.

2.Make sure bottom phone jack is plugged in.

3.Remove Tilt Stand from Tilt Stand Base (see Figure 11-21).

4.Place the spacers on the outer holes, as shown (see Figure 11-22).

5.Attach Tilt Stand to bottom of DKT with screws.

6.Reinstall the Tilt Stand Base: Fit the Tilt Stand Base over the Tilt Stand so that the “bottom pegs” fit into the holder. Adjust Tilt Stand so that the “top pegs” fit into the top Tilt Stand Base holes. Do this to both stands.

7.Pull up on the Tilt Stand Bases so that they open to the maximum angle (30 degrees). See Figure 11-23.

8.Push in the Lock Release button to adjust the tilt angle (0, 10, 20 or 30 degrees) of each Tilt Stand.

2 ADMs + 1 DKT (or 1 IPT)

 

 

 

 

 

 

 

 

 

 

ADMs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DKT/IPT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(A) Spacer

1 ADM

DKT

 

 

PHONE

1 ADM

PHONE

 

 

2 ADM

 

 

 

 

2 ADM

 

 

 

 

1 ADM

 

 

 

1 ADM

DKT

 

 

2 ADM

1 ADM

2 ADM

2 ADM

PHONE

 

PHONE

 

PHONE

1 ADM

 

 

 

2 ADM

PHONE

1 ADM

2 ADM

6527

(A) Spacer

Put in three screws in the

Put in three screws in the

positions marked “2ADM.”

positions marked “PHONE.”

Insert a spacer beneath each stand as shown. Put in the screw with the spacer first. Then insert the other two screws.

Figure 11-22 Attach Tilt Stands to DKT/IPT with Two ADMs

11-26

Strata CTX I&M 06/04

Page 424
Image 424
Toshiba CTX28 manual Tilt Stand for DKT/IPT + Two ADMs, 11-26