
POST Messages
Power-on Self Test (POST) Messages
The following table shows error messages that can appear on the scree
Notes:
1.The actions for some of the messages require you to run the Configuration/Setup Utility. For information about using these programs, “Using the Configuration/Setup Utility” on page 22.
2.If a password prompt appears with a POST message, type the admini
POST Message Table
POST Message | Description |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
062 | The | Netfinity | 5000 | server | failed | to | boot on | three consecutive | attempts. |
| ||||||||
| All | caches | are | disabled. This | can be caused by repeatedly turning the | |||||||||||||
| 5000 | server | on | and | then | off or | resetting the Netfinity 5000 server. |
| ||||||||||
| Action: Start the Configuration/Setup Utility program and verify that all set | |||||||||||||||||
| correct. (See | “The | Configuration/Setup | UtilityCache .”)ControlUse | theslection |
|
| |||||||||||
| in | the | Advanced | Setup | menu | of | the | Configuration/Setup | Utility program to | ena | ||||||||
| the caches. (See “Advanced Setup” | on | page 28.) |
|
|
|
| |||||||||||
| If the problem persists, have | the | system | serviced. When the | problem | is | ||||||||||||
| make | sure | to | enable the | caches. |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||
101 | An | error | occurred | during | the | system | board | and microprocessor | test. |
| ||||||||
102 | Action: | Have the | system | serviced. |
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
106An error occurred during the system board and microprocessor test. Action: Have the system serviced.
114 | An | adapter | memory | (ROM) | error | occurred. |
|
|
|
|
|
| ||||||
| Action: | Remove |
| the options. If you can start the server | without | the | optio | |||||||||||
| installed, reinstall each option one | at a | time and | retest | after | each | is | |||||||||||
| When | an | option | fails, | replace | it. |
|
|
|
|
|
|
|
|
| |||
| If |
| you | cannot | isolate and correct the problem, have the | system | serviced | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
129 | An | error | was |
| detected in | the | L1 | cache | of | one | of | the | microprocessors. | |||||
| Action: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 1. If | you | just installed | a microprocessor, | verify | that | the microprocesso | |||||||||||
|
| and seated | correctly. |
|
|
|
|
|
|
|
|
|
|
|
2.If the problem persists, check to see if the system has isolated microprocessor:
Ÿ If | the System | Error LED | on | the | information | LED panel is on, check to |
any | Microprocessor Error | LEDs | on | the system | board are on (see “Syste | |
Board LEDs” on | page 168). |
|
|
|
|
–If a Microprocessor LED is on, run the diagnostic program for the microprocessor indicated by the LED (if the secondary microproce error LED is on, runAlt. theCPU diagnostic program). If the tests fail, replace the microprocessor.
– If the microprocessor tests do not fail, have the system servic
ŸIf no error LED is on, the error logs in the Configuration/Setup Uti
program might provide additional information on the microprocessor error
If the problem persists, have the system serviced.
151 | A |
Action: Have the system serviced.
114 Netfinity 5000 Server Hardware Information and Procedures