Manuals / IBM / Computer Equipment / Computer Hardware

IBM 5000 manual NDIS 2.01 OS/2 Driver Messages, Ethernet Controller Messages

Models: 5000

1 204

Download 204 pages 30.32 Kb

Page 146

NDIS 2.01 (OS/2) Driver Messages

Protocol Manager registration failed.

The NDIS stack is not configured correctly. Check and correct your configuration.

The NDIS stack is not configured correctly in the PROTOCOL.INI file. Check and correct your configuration.

The NDIS stack is not configured correctly in the PROTOCOL.INI file. Check and correct your configuration.

The NDIS stack is not configured correctly. Check and correct your configuration.

Ethernet Controller Messages

PCNTNW-NW-165 The device was not found at IOADDRESS.

Explanation: The Ethernet controller cannot be found at the I/O address specified.

Action: The Ethernet controller does not require a parameter for the I/O address. Remove address parameter.

PCNTNW-NW-167 PCI scan specified, device not found.

Explanation: The driver cannot locate the Ethernet controller on the PCI bus.

Action: Verify that the PCI Ethernet device type is set to the default (enabled) pos Configuration/Setup utility programs (see “PCI Bus Control” on page 29).

If the problem persists, go to “Diagnostic Test Programs” on page 111 to run the diagno

PCNTNW-NW-180 The DMA parameter is not necessary for PCI device.

Explanation: The Ethernet controller does not require a DMA setting.

Action: None necessary, message is for information only.

NDIS 2.01 (OS/2) Driver Messages

This section contains the error messages for the NDIS 2.01 (OS/2) driv explanation and recommended action are included with each message.

PCNTND-1 Unable to open the Protocol Manager.

Explanation:

Action:

PCNTND-6 Out of memory while allocating buffers.

Explanation: The driver could not allocate the requested buffers.

Action: Check your system configuration. Edit the PROTOCOL.INI file to reduce the number o Txbuffers and Rxbuffers specified for the driver.


PCNTND-7	A	Protocol	Manager device error			occurred.
Explanation:		The		NDIS	stack	is	not configured correctly.
Action:		Check	and	correct		your	configuration.

PCNTND-8	Bad status for the Protocol Manager.
Explanation:		The		NDIS	stack	is	not configured correctly in the PROTOCOL.INI file.
Action:		Check	and	correct		your	configuration.

PCNTND-9 Cannot find the PROTOCOL.INI entry.

Explanation:

Action:

PCNTND-10 The Protocol Manager Input Output Control (IOCTL) failed.

Explanation:

Action:

PCNTND-11

Explanation:

Action:

138 Netfinity 5000 Server Hardware Information and Procedures

Image 146

IBM 5000 manual NDIS 2.01 OS/2 Driver Messages, Ethernet Controller Messages

Contents

Hardware Information and Procedures Netfinity 5000 ServerFirst Edition Tables Your ContentsYour Netfinity Enclosure Chapter 7. Server Records and SpecificationsChapter 5. Installing a Server in IndexSafety Information Statements Pred inštaláciou tohto zariadenia si pečítaje Bezpečnostné predpisyoutlet 3. Attach signal cables to receptacles Lithium Battery Notice Laser Compliance Statement Laser Compliance StatementNotices Used in This Book About This BookHow This Book is Organized Notices Used in This BookRelated Publications Related PublicationsNetfinity Chapter 1. Introducing YourStatus Indicators Features at a GlanceControls and Indicators Input/Output ConnectorsFeatures at a Glance Features at a GlanceWhat Your IBM Netfinity 5000 Server Offers Note TheChapter 1. Introducing Your Netfinity5 Serviceability Features Reliability, AvailabilityServer Controls Controls and IndicatorsControls and Indicators might Controls and Indicators8 Netfinity 5000 Server Hardware Information and Procedures cordSCSI Status IndicatorsControls and Indicators Light Controls and IndicatorsSystem HardChapter 1. Introducing Your Netfinity115000 Controls and IndicatorsSupply Input/Output Connectors Input/Output ConnectorsParallel Chapter 1. Introducing Your Netfinity13Expansion Bays Expansion BaysChapter 2. Arranging Your Workspace Arranging Your WorkspaceGlare and Lighting Arranging Your WorkspaceComfort 16 Netfinity 5000 Server Hardware Information and ProceduresAdditional Planning Considerations Air CirculationElectrical Outlets and Cable Lengths Arranging Your WorkspaceChapter 3. Configuring ServerConfiguration Overview Configuration OverviewThe Configuration/Setup Utility UtilitySystem Summary Using the Configuration/Setup UtilityUsing the Configuration/Setup System InformationSystem Card Data Devices and I/O PortsProduct Data PCI RoutingUsing the Configuration/Setup Utility Date and TimeSystem Security To set, change, or delete a password 1. SelectSystem Security4. Select Change Using the Power-on Password MenuUsing the Configuration/Setup Utility Arrow→ key Ÿ IfUsing the Configuration/Setup Utility Again Using the Administrator Password MenuUsing the Configuration/Setup Utility System Advanced SetupStart Options Using the Configuration/Setup UtilityServer Processor IRQ Settings Memory SettingsAdvanced ISA Settings Core Chipset ControlResolving Configuration Conflicts Error LogResolving Configuration Conflicts Plug and PlayResolving Configuration Conflicts ConflictsConflicts Controller Configuring the Ethernet ControllerConfiguring the Ethernet Failover for Redundant Ethernet Failover for Redundant EthernetFailover for Redundant Ethernet Configuring Failover on OS/2Configuring Failover on Windows Using the SCSISelect Utility Program Configuring Failover on IntraNetWareUsing the SCSISelect Utility Program Starting the SCSISelect ProgramSCSISelect Utility Program Choices Using the SCSISelect Utility ProgramUsing the SCSISelect Utility Program UtilitiesDisk Starting the Low-Level Format When To Use the Format Disk ProgramPerforming a Low-Level Disk Format Diskcontains Chapter 4. Installing OptionsThis Before You Begin Before You BeginElectrical Safety Electrical SafetyHandling Static-Sensitive Devices Handling Static-Sensitive DevicesOptions Preparing to InstallPreparing to Install Options cord Preparing a Tower ModelPreparing to Install Options cordsBezel Release Lever Preparing to Install OptionsChapter 4. Installing Options45 46 Netfinity 5000 Server Hardware Information and Procedures Preparing a Rack ModelPreparing to Install Options Preparing to Install Options Preparing to Install Options 48 Netfinity 5000 Server Hardware Information and ProceduresWorking with Adapters Working with AdaptersAdapter Considerations begin Installing or Removing AdaptersWorking with Adapters Note TheColor Working with AdaptersCard Type Card52 Netfinity 5000 Server Hardware Information and Procedures Working with AdaptersChapter 4. Installing Options53 Working with AdaptersWorking with Memory Modules Installing or RemovingModules Working with MemoryWorking with Memory Modules Location of Bays Installing or Removing Internal DrivesInstalling or Removing Internal Drives SCSI Types of CablesInstalling or Removing Internal Drives Installing or Removing Internal Drives SCSI DevicesSCSI IDs Termination Requirements Preinstallation StepsBays Installing or Removing Internal DrivesDrives in BaysB Removable Installing or Removing Internal DrivesInstalling or Removing Internal Drives Chapter 4. Installing Options61Installing or Removing Internal Drives DriveDiskette Drive Installing or RemovingChapter 4. Installing Options63 Installing or Removing Drives in Bays 1 through 5 Hard Disk DrivesInstalling or Removing Internal Drives Installing or Removing Internal Drives 64 Netfinity 5000 Server Hardware Information and ProceduresDrives Installing orChapter 4. Installing Options65 Removing InternalInstalling Microprocessors Installing MicroprocessorsInstalling Microprocessor Upgrades Computer Installing or Replacing a MicroprocessorInstalling Microprocessors Tabs Installing Microprocessors68 Netfinity 5000 Server Hardware Information and Procedures down Installing MicroprocessorsChapter 4. Installing Options69 70 Netfinity 5000 Server Hardware Information and Procedures Installing MicroprocessorsTable 3. Switch Settings for Microprocessor Speed Installing or Replacing Installing or Replacing the Power SupplyAdding External SCSI Devices Connecting External OptionsConnecting External Options To attach an external option Attaching External OptionsConnecting External Options Cable Installing a U-BoltAdding Security Adding SecurityChapter 4. Installing Options75 Adding SecurityCompleting the Installation Completing the InstallationCompleting the Tower Model Installation Completing the Installation 2. Replace the bezel, if it was removedWhat to do next Completing the Installation78 Netfinity 5000 Server Hardware Information and Procedures Completing the Rack Model Installation Completing the InstallationCompleting the Installation 80 Netfinity 5000 Server Hardware Information and ProceduresCompleting the Installation Chapter 4. Installing Options81Updating the Server Configuration Updating the Server ConfigurationSerial Port Connectors Note SerialManagement Port C 84 Netfinity 5000 Server Hardware Information and ProceduresParallel Port Connector EPP signalVideo Port Connector 6. Video Port Connector Pin-Number AssignmentsKeyboard and Mouse Connectors Internal SCSI Connector SCSI ConnectorsExternal SCSI Connector Signal the 68-pin SCSI connectorsSignal Chapter 4. Installing Options89Ports Universal Serial BusEthernet Connector 10. Ethernet Connector Pin-Number AssignmentsServer in Chapter 5. InstallingInstalling the Server in a Rack Enclosure a Rack EnclosureBefore You Begin 94 Netfinity 5000 Server Hardware Information and ProceduresBefore You Begin Netfinity 5000 Server Operating Specifications Before You BeginEnclosure Installing the Rack ModelInstalling the Rack Model in a Rack Enclosure Preparing the ServerInstalling the Rack Model in a Rack Enclosure Chapter 5. Installing a Server in a Rack97 EnclosureTo attach the mounting hardware to the rack enclosure Preparing the Rack EnclosureInstalling the Rack Model in a Rack Enclosure Installing the in aEnclosure Installing the Rack Model in a Rack Enclosure Installing the Rack Model in a Rack Enclosure Installing the Server in the Rack Enclosure Installing the Rack Model in a Rack EnclosureRack Installinga Rack Enclosure Rack Removing the Rack Model from a Rack Enclosurefrom EnclosureRemoving the Rack Model from a Rack Enclosure To remove the Netfinity 5000 server from a rack enclosureChapter 6. Solving Problems This chapter containsAfter Spilling Liquid .on. .It Replacing the Battery Identifying Problems Using Status. .LEDsPower Supply LEDs LED Diagnostics Recovering BIOS 108 Netfinity 5000 Server Hardware Information and ProceduresDiagnostic Test Programs Diagnostic Tools OverviewDiagnostic LEDs Diagnostic Tools OverviewPOST Beep Codes Power-On Self-Test POSTError Messages Diagnostic Tools OverviewDiagnostic Error Messages Troubleshooting ChartsPOST Error Messages and Beep Codes Software-Generated Error MessagesTests DiagnosticRunning Diagnostic Test ProgramsTo start the diagnostic tests Viewing the Test LogDiagnostic Test Programs SelectExtendedPOST Messages Power-on Self Test POST MessagesPOST Message Table page ixbefore POST MessagesPOST Message Action POST MessagesData someoneDescription menu,Memory selectSettingsPOST Messages POST Messages programsPOST POST Messagesremoving POST Messages downPOST Messages DescriptionPOST Beep Code Descriptions Power-on Self-Test POSTBeep Codes POST Beep CodesPOST Beep Codes One long andDIMM POST Beep Code TablePOST Beep Codes Diagnostic Messages Diagnostic MessagesDiagnostic Message Tables Text MessagesPort Failed Diagnostic MessagesSerial Port ParallelUSB Port PowerDiagnostic Messages MessagesDisplay Processor MessagesStatus MessagesDiagnostic Messages Function Diskette Drive MessagesSystem ActionFunction Hard DiskDiagnostic Messages That Failed Diagnostic MessagesProper Testing MessagesFunction Diagnostic MessagesSystem System Diagnostic MessagesMessages theCacheAction Diagnostic MessagesResult SCSI Messages SCSI MessagesSCSI Message Table Ethernet Controller Messages Ethernet Controller MessagesNovell NetWare or IntraNetWare Server ODI Driver Messages PCNTNW-NW-126 The Ethernet Controller Messagesparameter PCNTNW-NW-127 TheNDIS 2.01 OS/2 Driver Messages Ethernet Controller MessagesEthernet Controller Messages PCNTND-15 Device not foundcontains the error messages for the NDIS 4.0 Windows NT Driver MessagesUNIX Messages Ethernet Controller Messageshardware NETCONFIGEthernet Controller Messages Ethernet Controller Messages Troubleshooting Charts TroubleshootingTroubleshooting manualGeneral TroubleshootingMonitor Troubleshooting Problemsamount Troubleshootingmouse Memorysame TroubleshootingProblems ParallelPrinter Troubleshootingservice SystemController Troubleshooting the 10/100Network Connection Problems MbpsCheck 10/100 Mbps Ethernet Controller Troubleshooting ChartTroubleshooting whenController TroubleshootingProblem Resolving Memory-Address Conflicts SetupSetup Changing the SoftwareIdentifying Problems Using Status LEDs Identifying Problems Using Status LEDsPower Supply LEDs LED Diagnostics Identifying Problems Using Status LEDsIdentifying Problems Using Status LEDs Actionsdiagnostics have not detected a system err Identifying Problems Using Status LEDsŸ System Error information LED panel on the front of the NetfRecovering BIOS Recovering BIOSAfter Spilling Liquid on Checking the System for DamageAfter Dropping It Checking the System for DamageReplacing the Battery Replacing the Battery160 Netfinity 5000 Server Hardware Information and Procedures Replacing the BatteryTo replace the battery Server Records and Specifications Chapter 7. ServerRecord the Identification Numbers Record the IdentificationInstalled Device Records Installed Device RecordsDefault Installed Device RecordsConfiguration/Setup Program Defaults and Changes PageMouse Installed Device RecordsOption ChannelSetup Installed Device RecordsresourcesPlug. andThePlaydefault. value ControlTable 16. Expansion Slot Configuration Information Installed Device Records15. RAM Default Settings and Changes ExtendedDASD System Board IllustrationSystem Board LEDs System Board Connectors System Board Switches System Board SwitchesBypassing an Unknown Power-on Password BypassingChanging Jumper Positions Changing Jumper PositionsTwo-Pin Jumper Blocks SCSI Jumpers Tower AddressingPower Cords DASD Backplane Jumper Block LocationPart Usedin These Glossary Page EEPROM hexadecimalPage read-only power-onphysical Page virtual twistedutility 10BASE2Index Numerics POSTPage Page Endless EEPROMSee EEPROM NDISPOST messagescontinuedSee hard See ISA CD-ROMmemory continued Page See PCI alsomouseprograms 68-pinsecurity Page video port 86 view front 7 rear virus checking ð1K7717 IBMPart Number 01K7717 Printed in U.S.A September