Ethernet Controller Messages

PCNTNW-NW-074 The hardware interrupt cannot be set.

Explanation: An attempt was made to initialize a given hardware interrupt. The attempt w

successful.

Action: Verify that the PCI Ethernet device type is set to the default (enabled) p

Configuration/Setup utility programs (see

“PCI Bus Control” on page 29).

 

 

Make

sure that the interrupt request

numbers

are set correctly. If

you are

using a

sure resources are reserved as ISA

Legacy

in the Configuration/Setup

utility

programs

Play”

on page 30.)

 

 

 

 

PCNTNW-NW-075 The Multiple Link Interface Driver (MLID) cannot be registered with the Link

Support Layer (LSL).

Explanation: An error occurred while the driver was trying to register with the LSL.

Action: Check the version of the NetWare or IntraNetWare Operating System. Make sure th driver is correct for the version of NetWare or IntraNetWare that you are using. R

PCNTNW-NW-079

The

Multiple

 

Link

 

Interface

Driver

(MLID)

 

did

not

initialize

MSMTx

Free

Count.

 

 

 

 

 

 

 

 

 

 

Explanation:

 

The MSMTx Free Count is not initialized correctly.

 

 

 

 

 

 

 

 

 

 

 

Action:

Restart

the

 

server. If

the problem persists, have the

system

serviced.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PCNTNW-NW-086

The

driver

parameter

 

block

 

is

too

small.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Explanation:

 

The driver parameter block is too small.

 

 

 

 

 

 

 

 

 

 

 

 

 

Action:

Restart

the

 

server. If

the problem persists, have the

system

serviced.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PCNTNW-NW-087

The

media parameter

block

is

too

small.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Explanation:

 

The driver media parameter block is too small.

 

 

 

 

 

 

 

 

 

 

 

Action:

Restart

the

 

server. If

the

 

problem

 

persists,

have

the

system

serviced.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PCNTNW-NW-091 The hardware configuration conflicts.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Explanation:

 

You

tried

to

load

a

new

frame

type

for the existing controller. The hard

made in doing so are incorrect. This error can also occur if

you

try

 

to

specify

a

redundancy)

that

conflicts

with

another

specified

mode.

 

 

 

 

 

 

 

 

 

 

 

 

Action:

Make

sure

that

your

hardware

configuration

matches the software settings. See

 

Control”

on

page 29

for

information

on

 

viewing

 

and

changing

interrupt

requests.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PCNTNW-NW-126 The

group

bit

in

 

the

 

node

address

override

was

cleared.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Explanation:

 

The IEEE address has a group bit indicating that an address

belongs

to

a

stations. This bit is used only

as

a

destination

address;

it

 

cannot be used as a s

tried

to enter a source address

with

this

bit

set. The driver cleared the group

Action:

None

necessary,

message

is

for

information

only.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PCNTNW-NW-127 The

local

 

bit

in

 

the

 

node

address

override

was

set.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Explanation:

 

The

local

bit

 

in

the IEEE address format indicates

 

that

the

addresses

ar

locally. If

you

 

use

 

the

node

address

override

capabilities

of

this

driver to

enter

bit must be set. You entered

an

address

without the

local

bit

set. The

driver

has

Action:

None

necessary,

message

is

for

information

only.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PCNTNW-NW-164 The device was not found.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Explanation:

 

The

driver

cannot

find

an

 

Ethernet

controller

in

the

 

server.

 

 

 

 

 

 

Action: Verify that the PCI Ethernet device type is set to the default (enabled) p Configuration/Setup utility programs (see “PCI Bus Control” on page 29). If the Ethernet enabled, go to “Diagnostic Test Programs” on page 111 to run the diagnostic utility.

Chapter 6. Solving Problems 137

Page 145
Image 145
IBM 5000 manual PCNTNW-NW-074 The hardware interrupt cannot be set, Did, Initialize, Small, Bit, Was Set