POST Messages
POST Message | Description |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
962 | A | parallel |
| port | configuration | error | occurred. |
|
|
|
|
|
| ||||||||
| Action: | If | you | changed | a | hardware | option, make sure that the parallel po | ||||||||||||||
| is correct in the Configuration/Setup | utility programs. If the setting is | n | ||||||||||||||||||
| change it. For information about using | the | Configuration/Setup | utility | programs, | ||||||||||||||||
| “Using the | Configuration/Setup Utility” on page 22. |
|
|
|
|
| ||||||||||||||
| If | the | problem | persists, | have | the | system | serviced. |
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
| ||||||||||||
11xx | An | error | occurred during the | serial | port | test. |
|
| |||||||||||||
| Action: | If | you | have a | modem, | serial | printer, or other serial device atta | ||||||||||||||
| server, verify that the serial cable is connected correctly. If it is, |
| |||||||||||||||||||
| procedure: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| 1. Turn | off | the | server. |
|
|
|
|
|
|
|
|
|
|
|
| |||||
| 2. Disconnect | the | serial cable | from | the | serial | port. |
|
|
|
|
| |||||||||
| 3. Wait | five seconds; | then, | turn | on | the | server. |
|
|
|
|
|
| ||||||||
| If | the | POST | error | message | does |
| not | reappear, either | the |
| serial | cable | o | |||||||
| is probably failing. See the documentation that comes with the serial devi | ||||||||||||||||||||
| additional | testing | information. |
|
|
|
|
|
|
|
|
|
|
| |||||||
If the POST error message reappears, have the system serviced.
1162 | The serial port configuration conflicts with another device in the system. |
Action:
1.Make sure the IRQ and I/O port assignments needed by the serial po available. (See “The Configuration/Setup Utility” on page 21.)
2.If all interrupts are being used by adapters, you might need to re adapter to make an interrupt available to the PCI adapter, or force adapters to share an interrupt. For information about removing adapters, “Installing or Removing Adapters” on page 50. For information about setting interrupts, see “The Configuration/Setup Utility.”
1600 | POST is | unable to | communicate with the | processor. |
|
| |||||
| Action: |
|
|
|
|
|
|
|
|
|
|
| 1. If | the | Service Processor | Error LED (CR49) on the | system | board | is | on, | |||
| your | system | serviced. (See | “System | Board LEDs” on | page 168 | for | the | loc | ||
| of | the | LED.) |
|
|
|
|
|
|
| |
2. If the Service Processor Error LED is not on, disconnect the Netfinity server from all electrical sources, wait for 30 seconds, reconnect the 5000 server to the electrical sources, and restart the Netfinity 5000 se
| If | the | problem persists, | have | the system | serviced. |
|
|
| ||||
1601 | The | Advanced | System | Management controller BIOS | needs to | be | updated. | ||||||
| Action: |
|
|
|
|
|
|
|
|
|
|
| |
| 1. Disconnect | the | server | from | all | electrical | sources, | wait |
| for 30 seconds | |||
|
| the | server to | the electrical | sources, | and | restart | the |
| server. | |||
2.If the problem persists, update the Advanced System Management controlle BIOS. Refer to the “Getting Help Information”ServersectionLibraryoffor this information about obtaining updates.
1800 | A PCI adapter has requested a hardware interrupt that is not available. |
Action:
1.Make sure that the PCI adapter and all other adapters are set corr Configuration/Setup utility programs. If the interrupt resource settings a
correct, change the settings. See “PCI Bus Control” on page 29.
2.If all interrupts are being used by other adapters, you might need adapter to make an interrupt available to the PCI adapter, or force adapters to share an interrupt. For information about removing adapters, “Installing or Removing Adapters” on page 50. For information about setting interrupts, see see “PCI Bus Control” on page 29.
118 Netfinity 5000 Server Hardware Information and Procedures
