Panasonic A4P Series instruction manual Noise, Filter, Cable, For signal contactor

[Preparation]

Driver

￿

￿

￿

￿

￿

￿

￿

￿

￿

￿

￿

￿

MFDD

Applicable￿				Rated￿	Required￿ Circuit￿		Noise￿
		Voltage			Power￿ breaker￿
motor				output	(at the rated￿(rated ￿		filter
					load)	current)
MGMA￿			￿	2.0kW￿	approx.￿	￿	￿
			￿		3.8kVA￿
￿			￿	￿	￿	￿	￿
MDMA￿				￿		￿	￿
			￿		￿
￿				￿		￿	￿
			￿		￿
MHMA￿				￿		￿	￿
			￿		approx.￿
￿				3.0kW￿		￿	￿
			￿		4.5kVA￿
MSMA￿			￿	￿	￿	￿	￿
￿				￿		￿	￿
			￿		￿
MGMA￿				￿		￿	￿
			￿		￿
￿				￿		￿	￿
			￿		￿
MDMA￿				￿		￿	￿
					￿
￿	3- phase,￿			￿		￿	￿
					approx.￿
MHMA￿ 200V				4.0kW￿		50A	DV0P3410
					6kVA￿
￿				￿	￿
MSMA￿				￿
					￿
￿				￿
					approx.￿
MFMA￿				￿
					6.8kVA￿
￿				4.5kW￿
			approx.￿
MGMA￿				￿	7.5kVA￿
￿				￿
					￿
MDMA￿				￿
					￿
￿				￿
					approx.￿
MHMA￿				5.0kW
					7.5kVA
￿
MSMA

Surge￿ absorber

￿

￿

￿

￿

￿

￿

￿

￿

￿

￿

￿

￿

DV0P1450

Noise filter￿ Magnetic￿		Cable￿	Cable￿	Connection
for signal contactor		diameter￿	diameter￿
		(main circuit)	(control circuit)
￿	￿	￿	￿
	￿	￿	￿
￿
	￿	￿	￿
￿
	￿	￿	￿
￿
	BMF6352N￿	￿	￿
￿
	(3P+2a2b)￿	￿	￿
￿
	￿	￿	￿
￿
	￿	3.5mm2￿	￿
￿
	￿	AWG12￿	￿	Terminal￿
￿
	￿	￿	￿
￿					block￿
	￿	￿	￿
￿					M5
	￿	￿
￿			0.75mm2￿	11.0 or￿
	￿	￿
DV0P1460				smaller
	￿	￿	AWG18￿
	￿	￿	￿
	￿	￿	￿	ø5.3
	￿	￿	￿
	BMF6652N￿	￿	￿
	(3P+2a2b)	￿
		￿
		5.3mm2
		AWG10￿

Preparation

•Select a single and 3-phase common specifications according to the power source.

•Manufacturer of circuit breaker and magnetic contactor : Matsushita Electric Works.

To comply to EC Directives, install a circuit breaker between the power and the noise filter without fail, and the circuit breaker should conform to IEC Standards and UL recognized (Listed and marked). 5000Arms, 240V is the maximum capacity to be delivered to the circuit of 750W or larger model when the maximum current value of the circuit breaker is limited to 20A.

•For details of noise filters, refer to P.177, 178, "Noise Filter" and P.179, "Driver and List of Applicable Peripheral Equipments (EC Directives)" of Supplement.

<Remarks>

•Select and use the circuit breaker and noise filter with matching capacity to those of the power source, considering the load conditions as well.

•Terminal block and protective earth terminal

Use a copper conductor cable with temperature rating of 60˚C or higher. Protective earth terminal is M4 for A to D-frame, and M5 for E and F-frame.

Larger tightening torque of the screw than the max. value (M4 : 1.2 N•m, M5 : 2.0 N•m) may damage the terminal block.

•Earth cable diameter should be 2.0mm2 (AWG14) or larger for 50W to 2.0kW model, and 3.5mm2 (AWG12) or larger for 2.5kW to 4.0kW, and 5.3mm2 (AWG10) or larger for 4.5kW to 5kW model.

•Use the attached exclusive connectors for A to D-frame, and maintain the peeled off length of 8 to 9mm.

•Tightening torque of the screws for connector (CN X5) for the connection to the host to be 0.3 to 0.35 N•m. Larger tightening torque than these may damage the connector at the driver side.

33