Teledyne instruction manual Model 9110T NOx Analyzer Table of Contents

Model 9110T NOx Analyzer		Table of Contents
5.9. SETUP  Diag: Diagnostics Functions			114
5.9.1. Signal I/O			116
5.9.2. Analog Output (DIAG AOUT)			117
5.9.3. Analog I/O Configuration (DIAG AIO)			117
5.9.4. Test Chan Output (Selecting a Test Channel Function for Output A4)			132
5.9.5. Optic Test			133
5.9.6. Electrical Test			134
5.9.7. Ozone Gen Override			134
5.9.8. Flow Calibration			134
6. Communications Setup and Operation			135
6.1. Data Terminal / Communication Equipment (DTE DEC)			135
6.2. Communication Modes, Baud Rate and Port Testing			135
6.2.1. Communication Modes			135
6.2.2. Com Port Baud Rate			138
6.2.3. Com Port Testing			138
6.3. RS-232			139
6.4. RS-485 (Option)			140
6.5. Ethernet			140
6.5.1. Configuring Ethernet Communication Manually (Static IP Address)			140
6.5.2. Configuring Ethernet Communication Using Dynamic Host Configuration Protocol (DHCP)			143
6.6. USB Port for Remote Access			147
6.7. Communications Protocols			149
6.7.1. MODBUS			149
6.7.2. Hessen			151
7. Data Acquisition System (DAS) and APICOM			163
7.1. DAS Structure			164
7.1.1. DAS Channels			164
7.1.2. Viewing DAS Data and Settings			168
7.1.3. Editing DAS Data Channels			169
7.2. Remote DAS Configuration			181
7.2.1. DAS Configuration via APICOM			181
7.2.2. DAS Configuration via Terminal Emulation Programs			183
8. Remote Operation	185
8.1. Computer Mode			185
8.1.1. Remote Control via APICOM			185
8.2. Interactive Mode			185
8.2.1. Remote Control via a Terminal Emulation Program			185
8.3. Remote Access by Modem			188
8.4. Password Security for Serial Remote Communications			191
9. Calibration Procedures 193
9.1. Before Calibration			194
9.1.1. Required Equipment, Supplies, and Expendables			194
9.1.2. Calibration Gases			195
9.1.3. Data Recording Devices			196
9.1.4. NO2 Conversion Efficiency (CE)			197
9.2. Manual Calibration Checks and Calibration of the 9110T Analyzer in its Base Configuration			197
9.2.1. Setup for Basic Calibration Checks and Calibration of the 9110T analyzer			197
9.2.2. Performing a Basic Manual Calibration Check			199
9.2.3. Performing a Basic Manual Calibration			199
9.3. Manual Calibration with the Internal Span Gas Generator			202
9.3.1. Performing “Precision” Manual Calibration when Internal Span Gas (IZS) Generator Option is Present			202
9.3.2. Setup for Calibration with the Internal Span Gas Generator			203
9.3.3. CAL On NO2 Feature			203
9.3.4. Performing a Manual Calibration Check with the Internal Span Gas Generator			205
9.3.5. Performing a Manual Calibration with the Internal Span Gas Generator			206
9.4. Manual Calibration and Cal Checks with the Valve Options Installed			209
9.4.1. Setup for Calibration Using Valve Options			209
9.4.2. Manual Calibration Checks with Valve Options Installed			210
9.4.3. Manual Calibration Using Valve Options			211
9.5. Automatic Zero/Span Cal/Check (AutoCal)			213
9.5.1. SETUP  ACAL: Programming and AUTO CAL Sequence			216
9.6. Calibration Quality Analysis			219
9.7. Gas Flow Calibration			220
10. EPA Protocol Calibration			221
10.1. 9110T Calibration – General Guidelines			221

Teledyne Analytical Instruments 12