Teledyne instruction manual Model 9110TH NOx Analyzer Table of Contents

Model 9110TH NOx Analyzer	Table of Contents
10.2. Calibration Equipment, Supplies, and Expendables	222
10.2.1. Spare Parts and Expendable Supplies	222
10.2.2. Calibration Gas and Zero Air Sources	223
10.2.3. Data Recording Device	223
10.2.4. Record Keeping	223
10.3. Calibration Frequency	223
10.4. Level 1 Calibrations versus Level 2 Checks	224
10.5. Gas Phase Titration (GPT)	225
10.5.1. GPT Principle of Operation	225
10.5.2. GPT Calibrator Check Procedure	225
10.6. GPT Multipoint Calibration Procedure	228
10.6.1. Set Up for GPT Multipoint Calibration of the 9110T	229
10.6.2. Zero Calibration	230
10.6.3. Span Calibration	230
10.7. GPT NO2 Check	231
10.8. Other Quality Assurance Procedures	232
10.8.1. Summary of Quality Assurance Checks	232
10.8.2. Short Calibration Checks	233
10.8.3. Zero/Span Check Procedures	233
10.8.4. Precision Check	234
10.9. Certification of Working Standards	234
10.10. References	235
PART III – Maintenance and Service	237
11. Instrument Maintenance	239
11.1. Maintenance Schedule	239
11.2. Predictive Diagnostics	241
11.3. Maintenance Procedures	241
11.3.1. Replacing the Sample Particulate Filter	242
11.3.2. Changing the O3 Dryer Particulate Filter	243
11.3.3. Changing the Ozone Cleanser Chemical	244
11.3.4. Maintaining the External Sample Pump (Pump Pack)	247
11.3.5. Changing the Pump DFU Filter	247
11.3.6. Changing the Internal Span Gas Generator Permeation Tube	249
11.3.7. Changing the External Zero Air Scrubber (OPT 86C)	249
11.3.8. Changing the NO2 Converter	252
11.3.9. Cleaning the Reaction Cell	254
11.3.10. Replacing Critical Flow Orifices	256
11.3.11. Checking for Light Leaks	257
11.3.12. Checking for Pneumatic Leaks	258
12. Troubleshooting & Service	261
12.1. General Troubleshooting	261
12.1.1. Fault Diagnosis with WARNING Messages	262
12.1.2. Fault Diagnosis With Test Functions	266
12.1.3. DIAG  SIGNAL I/O: Using the Diagnostic Signal I/O Function	267
12.2. Using the Analog Output Test Channel	269
12.3. Using the Internal Electronic Status LEDs	270
12.3.1. CPU Status Indicator	270
12.3.2. Relay PCA Status LEDs	270
12.4. Gas Flow Problems	272
12.4.1. Zero or Low Flow Problems	272
12.5. Calibration Problems	276
12.5.1. Negative Concentrations	276
12.5.2. No Response	277
12.5.3. Unstable Zero and Span	277
12.5.4. Inability to Span - No SPAN Button (CALS)	278
12.5.5. Inability to Zero - No ZERO Button (CALZ)	278
12.5.6. Non-Linear Response	279
12.5.7. Discrepancy Between Analog Output and Display	280
12.5.8. Discrepancy Between NO and NOX slopes	280
12.6. Other Performance Problems	281
12.6.1. Excessive Noise	281
12.6.2. Slow Response	281
12.6.3. Auto Zero Warnings	282
12.7. Subsystem Checkout	283
12.7.1. AC Main Power	283

Teledyne Analytical Instruments 13