Hitachi X200 Series instruction manual See Input Terminal Configuration

B−36

The following table lists the holding registers for the “C” Group Intelligent Input Functions.

List of Holding Registers

Func.	Name	R/W	Description	Network Data
Code				Reg.	Range	Res.
C001	Terminal [1] function	R/W		1103h	0, 1, 2, 3,	−
C201	Terminal [1] function,	R/W		1532h	4, 5, 6, 7,
	2nd motor				8, 9, 11,
C002	Terminal [2] function	R/W		1104h	12, 13,
					15, 16,
C202	Terminal [2] function,	R/W		1533h
					18, 19,
	2nd motor
					20, 21,
C003	Terminal [3] function	R/W		1105h
			See “Input Terminal Configuration”		22, 23,
C203	Terminal [3] function,	R/W		1534h	24, 27,
	2nd motor		on page 3-49		28, 29,
C004	Terminal [4] function	R/W		1106h	31, 50,
					51, 52,
C204	Terminal [4] function,	R/W		1535h
	2nd motor				53, 64,
C005	Terminal [5] function	R/W		1107h	255
C205	Terminal [5] function,	R/W		1536h
	2nd motor
C011	Terminal [1] active state	R/W	Select logic conversion, two option	110Bh	0, 1	−
C012	Terminal [2] active state	R/W	codes:	110Ch	0, 1	−
C013	Terminal [3] active state	R/W	00…normally open [NO]	110Dh	0, 1	−
C014	Terminal [4] active state	R/W	01…normally closed [NC]	110Eh	0, 1	−
C015	Terminal [5] active state	R/W		110Fh	0, 1	−
C021	Terminal [11] function	R/W		1114h	0, 1, 2, 3,	−
			See “Output Terminal		4, 5, 6, 7,
C026	Alarm relay terminal	R/W	Configuration” on page 3-54	1119h	8, 9, 10,	−
	function				43
C028	[AM] signal selection	R/W	Two available functions:	111Bh	0, 1	−
			00…motor speed
			01…motor current
C031	Terminal [11] active	R/W	Select logic conversion:	111Dh	0, 1	−
	state		00…normally open [NO]
			01…normally closed [NC]
C036	Alarm relay active state	R/W	Select logic conversion:	1122h	0, 1	−
			00…normally open [NO]
			01…normally closed [NC]
C038	Output mode of low load	R/W	Three option codes:	1178h	0, 1, 2	−
	detection signal		00…Disabled
			01…During acceleration,
			deceleration and constant speed
			02…During constant speed only
C039	Low load detection level	R/W	Set the level of low load detection,	1179h	0 to	0.01%
			range is 0.0 to 2.0*rated current		20000
C041	Overload level setting	R/W	Sets the overload signal level	1124h	0 to	0.01%
			between 0% and 200% (from 0 to two		20000
			time the rated current of the
C241	Overload level setting,	R/W		153Ah
	2nd motor		inverter)
C042	Frequency arrival	R/W	Sets the frequency arrival setting	1126h	0 to 4000	0.1 Hz
	setting for acceleration		threshold for the output frequency		*1
			during acceleration,
			range is 0.0 to 400.0 Hz
C043	Frequency arrival	R/W	Sets the frequency arrival setting	1128h	0 to 4000	0.1 Hz
	setting for deceleration		threshold for the output frequency
			during deceleration,
			range is 0.0 to 400.0 Hz

Appendix B