measure swept harmonics, 2-81 measure swept RF/IF mixers, 3-7 measure transmission response in time

domain, 2-83

modify a sequence command, 2-72 modify calibration standards, 5-27 modify TRL calibration standards, 5-29 modify TRM calibration standards, 5-31 offset limit lines, 2-54

output a single page of values, 4-30 output multiple plots to a single page using

a printer, 4-25 output plot files, 4-20

output plot files from a PC to a plotter, 4-22

output plot files from a PC to a printer, 4-23

output single page plots using a printer, 4-24

output the entire list of values, 4-31 plot a measurement to disk, 4-19 plot measurements in page quadrants,

4-28

plot multiple measurements on a full page, 4-26

plot multiple measurements per page, 4-17, 4-26

plot one measurement per page, 4-16 plot to an HPGL compatible printer, 4-18 power meter calibrate, 3-6

print a sequence, 2-75

print multiple measurements per page, 4-7

print one measurement per page, 4-6 print or plot list values or operating

parameters, 4-30

purge a sequence from disk, 2-75

ratio measurements in channel 1 and 2, 2-8

recall a hle, 4-42

reduce receiver crosstalk, 5-57 reduce receiver noise floor, 5-56 reduce the averaging factor, 5-52 reduce the number of points, 5-52 reduce trace noise, 5-57 rename a file, 4-42

re-save a Rle, 4-41

reset plotting parameters to default values, 4-16

reset the printing parameters to default values, 4-6

review limit line segments, 2-53 run a limit test, 2-53

run a test sequence, 2-70

save a data trace to the display memory, 2-7

save an instrument state, 4-35 save measurement results, 4-36 search for a target amplitude, 2-34 search for bandwidth, 2-35

search for maximum amplitude, 2-32 search for minimum amplitude, 2-33 sequence tests, 2-68

set auto sweep time mode, 5-51

set center frequency with markers, 2-28 set CW frequency using markers, 2-31 set display reference using markers, 2-30 set electrical delay using markers, 2-31 set frequency range, 2-3

set frequency span with markers, 2-29 set source power, 2-4

set start frequency with markers, 2-27 set stop frequency with markers, 2-27 set the measurement parameters, 2-3 set the measurement type, 2-4

set the sweep type, 5-53

solve printing or plotting problems, 4-32 solve problems with disk storage, 443 stop a sequence, 2-70

store a sequence on a disk, 2-74 subtract the memory trace from the

measurement data trace, 2-8 title the active channel display, 2-9 title the displayed measurement, 4-29 track amplitude, 2-35

use analyzer display markers, 2-17

use continuous and discrete markers, 2-17 use delta (A) markers, 2-20

use frequency offset mode, 3-7 use limit lines, 246

use ~~~,~~~~, to wthte a axed reference marker, 2-23

use polar format markers, 2-24 use receiver calibration, 5-12 use Smith chart markers, 2-25

use swept list mode to increase sweep speed, 5-50

use the tuned receiver mc+e, 2-66

use the ~~~~~~~~.~ key to a&v&e

a tied reference marker, 2-22 view a single measurement channel, 5-53 view both primary channels, 2-6

view plot hles on a PC, 4-20

view the measurement data and memory trace, 2-7

widen system bandwidth, 5-52 HP 8753A/B/C/D differences, 1-15 HP 8753D/E differences, 1-15

Index-10

Page 683
Image 683
HP 8753E Domain, Print a sequence Print multiple measurements per, Set auto sweep time mode, Use analyzer display markers