Station No Command | Hitachi SJ700-2 specs

Chapter 4 Explanation of Functions

(x) 09 command: This command checks whether set data can be stored in the EEPROM in the inverter.

-Transmission frame Frame format

STX

Station No.

Command

BCC

CR

		Description	Data size	Setting
	STX	Control code (Start of TeXt)	1 byte	STX (0x02)
	Station No.	Station number of control-target	2 bytes	01 to 32
	Station No.	inverter	2 bytes	01 to 32
		inverter
	Command	Command to be transmitted	2 bytes	09
	BCC	Block check code	2 bytes	XOR of the items from "Station No." to "Data."
	BCC	Block check code	2 bytes	See Item (3) of this section.
				See Item (3) of this section.
	CR	Control code (Carriage Return)	1 byte	CR (0x0D)

-Response frame Frame format

STX

Station No.

ACK

Data

BCC

CR

		Description	Data size	Setting
	STX	Control code (Start of TeXt)	1 byte	STX (0x02)
	Station No.	Station number of control-target	2 bytes	01 to 32
	Station No.	inverter	2 bytes	01 to 32
		inverter
	ACK	Control code (acknowledgement)	1 byte	ACK (0x06)
	Data	Data	2 bytes	"01" (enabling data storage)
	BCC	Block check code	2 bytes	XOR of the items from "Station No." to "Data."
	BCC	Block check code	2 bytes	See Item (3) of this section.
				See Item (3) of this section.
	CR	Control code (Carriage Return)	1 byte	CR (0x0D)

Negative response: See Item (4)-(ii) of this section.

(xi)0A command: This command stores set data in the EEPROM in the inverter. - Transmission frame

Frame format

STX

Station No. Command

BCC

CR

		Description	Data size	Setting
	STX	Control code (Start of TeXt)	1 byte	STX (0x02)
	Station No.	Station number of control-target	2 bytes	01 to 32
	Station No.	inverter	2 bytes	01 to 32
		inverter
	Command	Command to be transmitted	2 bytes	0A
	BCC	Block check code	2 bytes	XOR of the items from "Station No." to "Data."
	BCC	Block check code	2 bytes	See Item (3) of this section.
				See Item (3) of this section.
	CR	Control code (Carriage Return)	1 byte	CR (0x0D)

- Response frame

Positive response: See Item (2)-(i) of this section.

Negative response: See Item (2)-(ii) of this section.

4 - 125

Image 183

Hitachi SJ700-2 instruction manual Station No Command, Data Bytes Enabling data storage

Contents

SJ700-2 Series Page Installation Safety Instructions ！ Warning Wiring Operation Maintenance, inspection, and parts replacement Precautions Concerning Electromagnetic Compatibility EMC Model No Required torque N-m Wire range AWG Or 1/013.7 60 a Model No Fuse/circuit breaker a Type Rating30 a 40 a Contents Contents Running time over and power-on time over signals RNT and ONT Contents Xii Error Codes Xiii Index Overview Page Specification label Inspection of the Purchased ProductInspecting the product Method of inquiry Method of Inquiry and Product WarrantyProduct warranty Warranty Terms Exterior Views and Names of Parts Installation and Wiring Page Installation and Wiring Inverter Precautions for installation Loss with 100% load W Ventilation fanInverter AcceptableUnacceptable Inverter capacity kW 18.5 Loss with 70% load W Backing plate Rubber bushing Joint Section to be cut off Wiring Hitachi Phase power supply Explanation of control circuit terminals Explanation of main circuit terminals AL0 SW1 OFF on Wiring of the main circuit Inverter Grounding bolt prepared by user Terminal layout Inverter model Charge lump Terminal layout Terminal layout Inverter model Charge lump Applicable peripheral equipment 100Inverter Motor 50/60 Hz ±5% 200 to 240 V +10%, -15%50/60 Hz ±5% 282 to 339 VDC 380 to 480 V +10%, -15% CM1 15 CM2 12 AL0 AL2 TH FW 8 CM1PL CM1 7 6 FW 8 CM1 14 13 11 AL1 Source logic When using the internal interface power supplyWhen using an external power supply Sink logic BRD Operation Page ！ Warning Operating Methods Frequency-setting command Input device control Device switchControl circuit terminal block How To Operate the Digital Operator OPE-S Monitor Power lamp Digit LED displayNames and functions of components Code display system and key operations Operation Corresponding to the function code. Data display *1*2 STR key after changing the data Parameter type Pressing the STR key Display the monitor mode code. d001 is displayed ELB How To Make a Test Run Key to decelerate or stop the motor Key to start the motor RUN lamp green LED goes on Press CM1 PLC This chapter describes the functions of the inverter Explanation of FunctionsPage Rotation direction monitoring Monitor ModeOutput frequency monitoring Output current monitoring Intelligent input terminal status Intelligent output terminal statusScaled output frequency monitoring Torque bias monitoring Torque command monitoringPower monitoring Actual-frequency monitoring Motor temperature monitoring Cumulative power monitoringCumulative power-on time monitoring Heat sink temperature monitoring Program number monitoring easy sequence function Current position monitor in absolute position control modeLife-check monitoring Program counter display easy sequence function BRD load factor monitoring Programming error monitoringTrip monitoring 1 to DC voltage monitoring Rotational direction restriction Function ModeOutput frequency setting Keypad Run key routing Active state C011 to C018 NC contact Frequency source settingRun command source setting No contact Stop key enable Stop mode selection Deceleration time tB Acceleration/deceleration time setting Maximum frequency setting Base frequency setting External analog input setting O, OI, and O2 +fO2 + fO2 Frequency operation function Frequency addition function Start/end frequency setting for external analog input External analog input O/OI/O2 filter setting 16 V/f gain settingStart/end frequency settings for the O2-L terminal VPf 17 V/F characteristic curve selection To free-setting V/f frequency 6 Hz Free-setting V/f frequencyTo 400.Hz Free-setting V/f frequency To free-setting V/f frequency 7 Hz Torque boost setting B083 DC braking DB setting Example 3-a Example 3-b Edge mode A056Example 1-a Example 1-b Example 2-a Example 2-b Ii Example 6-a when the stop command is input Ii Example 5-a when the stop command is input Edge mode Example 7-aExample 7-b Frequency upper limit setting When the O-L or OI-L terminal is usedWhen the O2-L terminal is used Frequency setting Acceleration Acceleration stop frequency settingSetting of 0 Hz disables the jump frequency function Setting of the length of time to stop PID function Operation targets are the inputs To the OI and O terminals OI-L + O2OI + O2 Operation targets include + O2 Input to the OI terminal 01 % FW on OFF FBV Onoff Two-stage acceleration/deceleration function 2CH Use functions A097 and A098 to select acceleration Acceleration/deceleration curve selectionYou can set different patterns of motor acceleration Inverter Energy saving mode tuning A086 Energy-saver operationAccuracy Retry or trip after instantaneous power failure Power supply Inverter output Motor speed Example 8 b00400 Example 5 b00400Example 6 b00401 Example 7 b00402 Disabling the protection Phase loss power input protectionFunction code Data Description Phase loss detection Enable Enabling the protection Electronic thermal protection Constant-torque characteristicCharacteristic Free setting of electronic thermal characteristic Disabling the electronic thermal protection Setting of the current at each breakpointSetting of the threshold level to output Thermal warning signal Overload restriction/overload notice Overcurrent restraint Over voltage supression during deceleration Reduced voltage start function Start frequency setting Class Carrier frequency setting Automatic carrier frequency reduction Function code Range of data Description Automatic carrier00/01 Invalid, 01 valid Frequency reduction Dynamic braking BRD function Cooling-fan operation setting Intelligent input terminal setting Input terminal a/b NO/NC selection If two or more input terminals are turned on at the same Bit operation modeBy setting multispeeds 1 to 7 A021 to A027 Make multispeed s 0 to 7 available for selection Jog stop mode Jogging JG command setting 43 2nd/3rd motor control function SET and SET3 Forcible-operation from terminal F-TM function Software lock SFT function Free-run stop FRS function Commercial power source switching CS function Reset RS function Example 4 Restarting with active matching frequency Unattended start protection USP function Remote control function UP and DWN External trip EXT function 53 3-wire interface operation function STA, STP, and F/R 55 P/PI switching function PPI Control gain switching function CAS Synchronous rotation speed at base frequency Analog command holding function AHDSpeed error at rated torque a Intelligent pulse counter Pcnt and PCC Intelligent output terminal setting Intelligent output terminal a/b NO/NC selection Example of operation as an alarm output terminal Disabling the output of frequency C042/C045 043/C046 63 0 Hz speed detection signal ZS Alarm code output function AC0 to AC3 Over-torque signal OTQ Logical output signal operation function LOG1 to LOG6 Communication line disconnection signal NDc Capacitor life warning signal WAC Cooling-fan speed drop signal WAF Starting contact signal FRHeat sink overheat warning signal OHF FWR Forward rotation signal Low-current indication LOC signalForward rotation signal FWR Irdy Inverter ready signal MJA Major failure signal Reverse rotation signal RVRMajor failure signal MJA RVR Reverse rotation signal WCO/WCOI/WCO2 Output signal delay/hold function Input terminal response timeExternal thermistor function TH Function code Range of data Description FM terminalPulse output terminal FM siginal selection AM and AMI terminals Initialization setting Function code display restriction Explanation of Functions Last equivalent to the setting on SJ300 Automatic user-parameter setting Stabilization constant settingSelection of operation at option board error Page Brake control function Release signal output until the release Signal has been output until the brake isBrake Wait Time for Mechanical delay after the release Wait time longer than the delay after B054 B053 B052 When using this function, follow the instructions below Offline auto-tuning function Normal end Abnormal end Disabling the secondary resistance compensation Online auto-tuning functionAutomatically tuned data online auto-tuning enabled Function code Data Description Temperature compensation Voltage class 200 or 400 Then adjust the speed response H005/H205Motor constants selection Io as follows Sensorless vector control Zero LV starting boost current Sensorless vector, 0 Hz domain controlZero LV lmit Current limiter for the low-speed range Motor capacity selection Torque monitoring functionForcing function FOC Output torque Torque limitation function Disabling counterrotation prevention Enable Enabling counterrotation preventionReverse Run protection function B041 B042 B044 B043 High-torque multi-motor operation Torque LAD stop function Personal computer Windows system Easy sequence function Functions requiring the SJ-FB 2 V2 control pulse setting Vector control with encoder feedback Torque-limited operation atOperation Torque limiter level Torque control function Torque biasing function 255 Pulse train position control modeControl block diagram Frequency command Hz = SBP ＳＢＰ MD1 Forward/reverse operation command with pulse train Electronic gear function P019 = 00 FBP019 = 01 REF Example of use Synchronous operation Master inverter Slave inverterMain motor Sub-motor Motor gear ratio setting function Setting of the actual pulseCount of encoder Home search function １０２４３０７２２０４８ Absolute position control mode Operation Output frequency Speed setting POK signal Operation in absolute position control mode Speed/position switching function SPD Multistage position switching function CP1/CP2/CP3 Forward direction at the low-speed Teaching selection P074 Position range specification functionForward/reverse drive stop function FOT/ROT Teaching function SON Fwrv Servo-on function To +100. % Pulse train frequency limit Block diagram for pulse train frequency inputSetting of the filter time constant for Pulse train frequency input Communication Functions Communication specifications Selection Modbus-RTU mode Set this item when your inverter isCommunication mode Ascii mode Explanation of Functions Communication in Ascii mode STX 0101000500 BCC CR 0230 3130 3130 30 30 35 30 3030 350D Data to be transmitted Explanation of Functions Response frame Frame format Status a Status B Status C Reserved DataInverter status a Inverter status B Inverter status C Data Bytes See Note Bytes Decimal Ascii code Output current Data monitored at trippingInverter status B Bytes Inverter status C Bytes Station No Station No. Command ParameterResponse frame Positive response Frame format Data parameter number Bytes See Note Station No. Command Parameter Data Station No. CommandParameter data decimal Ascii Bytes See Note Code Data Bytes Enabling data storage Explanation of Functions Ii Negative response Response frame Frame format Character data Ascii code Transmission frame configuration Station No. CommandReference Ascii code conversion table This result is used as BCC Communication in Modbus-RTU mode Writes data to a coil Function code Maximum number of dataReads the coil status Reads registers CRC*1 Specified address is not found Slave address Function code Exception code CRC-16Code Description An unsupported function is specified Terminal status Intelligent input terminal Coil number Read the data received in the response as follows Updating data lower digit Field name Sample settingCoil status Updating data upper digit FFh Intelligent input terminal Query Response Field name Sample setting 02h Specified address is not found Slave address Function code Exception code CRC-16 codeException codes 01h An unsupported function is specified Data to be written Description Recalculating the motor constantsStoring the register data Coil No Setting LOG2 logical operation result ON, 0 OFF Ii List of registers frequency settings and trip monitoring Register Function name Monitoring and setting items Data Option 1 error 0 to Option 2 error 0 toList of inverter trip factors Iv List of registers Iii List of registers monitoring List of registers function modes Start frequency to Monitoring and setting items Data resolution 12B4h Failure time Monitoring and setting items Data resolution Register During inverter operation including 5 minutes after EXT external trip, 13 USP unattended start Thermal overload, 07 LAD frequency, 09 motor C042 high 1487h Output 11 off-delay time C131 1506h Over-speed error detection level P026 Setting To the allowable maximum frequency Code data Vi List of registers 2nd control settings 2506h Motor Ix List of registers 3rd control setting Viii List of registers 3rd control settings Error Codes and Troubleshooting ···················· 5 Error CodesPage Error Codes Error Codes and Troubleshooting CPU GA.COM Adjust Option boards error codes Input mode specified by switch settings Setting of MAC ID DIP switches No to No Baud rate Kbps DIP switch setting= 29 hexadecimal = 41 decimal Error code is output when the relevant program runs Trip conditions monitoring 305 A004/A204/A304 A202/A220/A320 *2 006 DC-Bus Capacitor Life Curve Precautions for MaintenanceGround Resistance Test with a Megger Method of Checking the InverterPage Periodic inspection Precautions for Maintenance and InspectionCleaning Daily inspection Ground terminals with a megger Daily and Periodic Inspections Withstand Voltage Test Ground Resistance Test with a Megger Method of Checking the Inverter and Converter Circuits Output of Life Warning DC-Bus Capacitor Life Curve PfIN＝ Method to measure the output voltageMotor 2W 220ｋΩ Specifications External dimensions SpecificationsPage Common specifications of 200 V class and 400 V class models SpecificationsSpecifications of the 200 V class model Specifications of the 400 V class model Standard Model name type 055 075 110 150 185 220 300 370 450 550 Name External dimensions SJ700-055 to110LFF2/LFUF2 / HFF2/HFEF2/HFUF2SJ700-150 to 220 LFF2/LFUF2 / HFF2/HFEF2/HFUF2 SJ700-300 LFF2/LFUF2 / HFF2/HFEF2/HFUF2 SJ700-550 LFF2/LFUF2 Monitoring Mode Function Mode Extended Function Mode List of Data SettingsPage Precautions for Data Setting Function Mode Extended Function Mode PID AVR B004 Failure/under-voltage trip alarm To stop Enable Power Free-setting V/f voltage To 800.0 Input Analog C107 AMI gain adjustment To 200. % Setting C163 Input terminal response time To 200. ¯2ms Control Control RPM Specification List of Data Settings Allowed or Not No/d001 to P131 Upgrading from the SJ300 Series Appendix Copying the parameter settings Index Monitor mode Motor constant High-resolution absolute position Control 106Instantaneous power failure Instantaneous power failure or Running time over / power-on time Over Operation time over signal RNT/plug-in time over signalPhase loss input Phase loss input protection Remote operator Appendix-1 Reset Torque biasing Gain setting VP 1.7 th powerWindow comparator Wiring of control circuit terminal Thermistor