Hitachi SJ700-2 instruction manual Intelligent input terminal setting

Related code

C001 to C008: Terminal [1] to [8] functions

Chapter 4 Explanation of Functions

4.2.39 Intelligent input terminal setting

You can assign the functions described below to intelligent input terminals [1] to [8]. To assign the desired functions to the terminals, specify the desired data listed in the table below for terminal settings "C001" to "C008". For example, "C001" corresponds to intelligent input terminal [1].

You can select the a-contact or b-contact input for individual intelligent input terminals.

You can assign one function only to an intelligent input terminal. If you have attempted to assign a function to two or more intelligent input terminals, the function is assigned to only the terminal to which you have last attempted assignment. Function data "NO" (no assign) is assigned to other terminals, and those terminals are ineffective in terms of functions.

After assigning the desired functions to intelligent input terminals [1] to [8], confirm that the assigned functions have been stored on the inverter.

Function code	Data	Description	Reference item	Page
	01	RV: Reverse RUN command	Operation command	－
	02	CF1: Multispeed 1 setting (binary operation)
	03	CF2: Multispeed 2 setting (binary operation)	Multispeed operation function	4-47
	04	CF3: Multispeed 3 setting (binary operation)
	05	CF4: Multispeed 4 setting (binary operation)
	06	JG: Jogging	Jogging operation function	4-49
	07	DB: External DC braking	DC braking (external DC braking) function	4-20
	08	SET: Set 2nd motor data	2nd/3rd motor control function	4-50
	09	2CH: 2-stage acceleration/deceleration	2-stage acceleration/deceleration function	4-30
	11	FRS: Free-run stop	Free-run stop function	4-52
	12	EXT: External trip	External trip function	4-57
	13	USP: Unattended start protection	Unattended start protection function	4-56
	14	CS: Commercial power source enable	Commercial power supply switching function	4-53
	15	SFT: Software lock (control circuit terminal block)	Software lock function	4-51
	16	AT: Analog input voltage/current select	External analog input setting function	4-12
	17	SET3: 3rd motor control	2nd/3rd motor control function	4-50
	18	RS: Reset	Reset	4-54
	20	STA: Starting by 3-wire input	3-wire input function	4-57
	21	STP: Stopping by 3-wire input
	22	F/R: Forward/reverse switching by 3-wire input
	23	PID: PID disable	PID function	4-26
C001 to C008	24	PIDC: PID reset
	26	CAS: Control gain setting	Control gain switching function	4-58
	27	UP: Remote control UP function	Remote control (UP/DWN) function	4-56
	28	DWN: Remote control DOWN function
	29	DWN: Remote control data clearing
	31	OPE: Forcible operation	Forcible-operation function	4-51
	32	SF1: Multispeed 1 setting (bit operation)
	33	SF2: Multispeed 2 setting (bit operation)
	34	SF3: Multispeed 3 setting (bit operation)	Multispeed operation function	4-47
	35	SF4: Multispeed 4 setting (bit operation)
	36	SF5: Multispeed 5 setting (bit operation)
	37	SF6: Multispeed 6 setting (bit operation)
	38	SF7: Multispeed 7 setting (bit operation)
	39	OLR: Overload restriction selection	Overload restriction function	4-39
	40	TL: Torque limit enable	Torque limitation function	4-92
	41	TRQ1: Torque limit selection bit 1
	42	TRQ2: Torque limit selection bit 2
	43	PPI: P/PI mode selection	P/PI switching function	4-58
	44	BOK: Braking confirmation	Brake control function	4-81
	45	ORT: Orientation	Orientation function	4-96
	46	LAC: LAD cancellation	LAD cancellation function	4-10
	47	PCLR: Clearance of position deviation	V2 control mode selection function	4-96
	48	STAT: Pulse train position command input enable
	50	ADD: Trigger for frequency addition (A145)	Frequency addition function	4-14

4 - 46