Hitachi SJ700-2 instruction manual Display the monitor mode code. d001 is displayed

Chapter 3 Operation

(4)Procedure for directly specifying or selecting a code

-You can specify or select a code or data by entering each digit of the code or data instead of scrolling codes or data in the monitor, function, or extended function mode.

-The following shows an example of the procedure for changing the monitor mode code "d001" displayed to extended function code "A029":

1)Display the monitor mode code. ("d001" is displayed.)

	RUN	STOP/
		RESET
(*2)	FUNC	STR
(*3)

("A029" is displayed.)

(*2)

RUN STOP/

RESET

FUNCSTR

6) End the change of the extended function code.

Press the STR key.

	RUN	STOP/
		RESET
(Character "9"	FUNC	STR
is determined.)

FUNC	Press the	1 and	2 keys
	together.		(*1)

2) Change to the extended function mode.

RUN STOP/

RESET

FUNCSTR

-Character "d" in the leftmost digit (fourth digit from the right) starts blinking.

Press the 2 key twice.

("A001" is displayed.)

(*3)

- Character "9" in the first digit is blinking.

Press the	1		key eight
times or the		2	key twice.

5) Change the first digit of the code.

RUN STOP/

RESET

FUNCSTR

- Character "1" in the first digit is blinking.

(*2) Press the STR key.

FUNC

("A021" is displayed.)

- Selection of code "A029" is completed.

*If a code that is not defined in the code list or not intended for display is entered, the leftmost digit (fourth digit) (character "A" in this example) will start blinking again.

In such a case, confirm the code to be entered and enter it correctly. For further information, refer to Section 4.2.80. " Function code display restriction," (on page 4-74), Section 4.2.81, "Initial-screen selection," (on page 4-76), Section 4.2.82, "Automatic user-parameter setting," (on page 4-77), and Chapter 8, "List of Data Settings."

7)Press the FUNC key to display the data corresponding to the function code,

change the data with the 1	and/or
2 key, and then press the	STR key to

store the changed data. (*4)

Note that you can also use the procedure (steps 1) to 6)) described here to change the data. (*3)(*4)

RUN STOP/

RESET

FUNCSTR

-Character "A" is blinking.

-Pressing the [STR] key determines the blinking character.

(*2)

FUNC	Press the STR key
	(to determine character "A").

3) Change the third digit of the code.

(*2)

RUN STOP/

RESET

FUNCSTR

-Character "2" in the second digit is blinking.

Press the 1 key twice.

4) Change the second digit of the code.

*1

This procedure can also be used on screens displaying a code other than "d001".

*2

If the FUNC key is pressed while a digit is blinking, the display will revert to the preceding status for entering the digit to the right of the blinking digit.

*3

If the FUNC key is pressed while the leftmost (fourth) digit is blinking, the characters having been entered to change the code will be cancelled and the display will revert to the original code

RUN STOP/ RESET

		shown before the 1 and 2 keys
Press the STR		were pressed in step 1).
		*4
key.
		When changing data, be sure to press the
RUN	STOP/	FUNC key first.
	RESET
(Character "0" is
determined.)		STR
FUNC

FUNC	STR	(*2)
	FUNC
- Character "0" in the third digit is blinking.		- Character "0" in the second digit is
- Since the third digit need not be changed,		blinking.
press the [STR] key to determine the
character "0".

3 - 9