Hitachi SJ700-2 instruction manual C107 AMI gain adjustment To 200. %

Chapter 8 List of Data Settings

					Default			Setting	Change
								during	during
	Code	Function name	Monitored data or setting					operation	operation	Page
				_FF		_FEF	_FUF	(allowed	(allowed
								or not)	or not)
	C038	Low-current indication signal	00 (output during acceleration/deceleration and constant-speed operation),		01			¯	{
		output mode selection	01 (output only during constant-speed operation)							4-69
	C039	Low-current indication signal	0.0 to 2.00 x "rated current" (A)	Rated current of inverter				{	{
		detection level
	C040	Overload signal output mode	00 (output during acceleration/deceleration and constant-speed operation),		01			¯	{
			01 (output only during constant-speed operation)							4-40
	C041	Overload level setting	0.0 to 2.00 x "rated current" (A)	Rated current of inverter				{	{
	C042	Frequency arrival setting for accel.	0.00 to 99.99, 100.0 to 400.0 (Hz)		0.00			¯	{	4-62
	C043	Frequency arrival setting for decel.	0.00 to 99.99, 100.0 to 400.0 (Hz)		0.00			¯	{
status	C044	PID deviation level setting	0.0 to 100.0 (%)		3.0			¯	{	4-29
	C045	Frequency arrival setting for	0.00 to 99.99, 100.0 to 400.0 (Hz)		0.00			¯	{
terminal		acceleration (2)								4-62
	C046	Frequency arrival setting for	0.00 to 99.99, 100.0 to 400.0 (Hz)		0.00			¯	{
		deceleration (2)
output	C052	Maximum PID feedback data	0.0 to 100.0 (%)		100.0			¯	{	4-29
	C053	Minimum PID feedback data	0.0 to 100.0 (%)		0.0			¯	{
and	C055	Over-torque (forward-driving) level	0. to 200. (%)		100.			¯	{
Levels		setting
	C056	Over-torque (reverse	0. to 200. (%)		100.			¯	{
		regenerating) level setting								4-65
	C057	Over-torque (reverse driving) level	0. to 200. (%)		100.			¯	{
		setting
	C058	Over-torque (forward	0. to 200. (%)		100.			¯	{
		regenerating) level setting
	C061	Electronic thermal warning level	0. to 100. (%)		80.			¯	{	4-38
		setting
	C062	Alarm code output	00 (disabling), 01 (3 bits), 02 (4 bits)		00			¯	{	4-65
	C063	Zero speed detection level	0.00 to 99.99, 100.0 (Hz)		0.00			¯	{	4-64
	C064	Heat sink overheat warning level	0. to 200.0 (°C)		120.			¯	{	4-68
	C071	Communication speed selection	02 (loopback test), 03 (2,400 bps), 04 (4,800 bps), 05 (9,600 bps), 06		04			¯	{
			(19,200 bps)
	C072	Node allocation	1. to 32.		1.			¯	{
function	C074	Communication data length	00 (no parity), 01 (even parity), 02 (odd parity)		00			¯	{
		Communication parity selection
	C073	selection	7 (7 bits), 8 (8 bits)		7			¯	{
Communication
	C075	Communication stop bit selection	1 (1 bit), 2 (2 bits)		1			¯	{	4-113
		Selection of the operation after	00 (tripping), 01 (tripping after decelerating and stopping the motor), 02
	C076		(ignoring errors), 03 (stopping the motor after free-running), 04		02			¯	{
		communication error
			(decelerating and stopping the motor)
	C077	Communication timeout limit	0.00 to 99.99 (s)		0.00			¯	{
		before tripping
	C078	Communication wait time	0. to 1000. (ms)		0.			¯	{
	C079	Communication mode selection	00(ASCII), 01(Modbus-RTU)		00			¯	{
Adjustment	C081	[O] input span calibration	0. to 9999., 1000 to 6553(10000 to 65530)	Factory setting				{	{
	C085	Thermistor input tuning	0.0 to 999.9, 1000.	Factory setting				{	{	4-72
	C082	[OI] input span calibration	0. to 9999., 1000 to 6553(10000 to 65530)	Factory setting				{	{	−
	C083	[O2] input span calibration	0. to 9999., 1000 to 6553(10000 to 65530)	Factory setting				{	{
	C091	Debug mode enable	(Do not change this parameter, which is intended for factory adjustment.)		00			¯	¯	−
	C101	Up/Down memory mode selection	00 (not storing the frequency data), 01 (storing the frequency data)		00			¯	{	4-56
Others	C102	Reset mode selection	00 (resetting the trip when RS is on), 01 (resetting the trip when RS is off), 2		00			{	{	4-54
			(enabling resetting only upon tripping [resetting when RS is on])
	C103	Restart mode after reset	00 (starting with 0 Hz), 01 (starting with matching frequency), 02 (restarting		00			¯	{
			with active matching frequency)
Meter adjustment	C105	FM gain adjustment	50. to 200. (%)		100.			{	{	4-73
	C109	AM bias adjustment	0. to 100. (%)		0.			{	{
	C106	AM gain adjustment	50. to 200. (%)		100.			{	{
	C107	AMI gain adjustment	50. to 200. (%)		100.			{	{	4-74
	C110	AMI bias adjustment	0. to 100. (%)		20.			{	{

8 - 11