Hitachi SJ700-2 instruction manual Power

Chapter 8 List of Data Settings

					Default		Setting	Change
	Code	Function name	Monitored data or setting				during	during	Page
							operation	operation
				_FF	_FEF	_FUF	(allowed or	(allowed or
							not)	not)
	b034	Run/power-on warning time	0. to 9999. (0 to 99990), 1000 to 6553 (10000 to 655300) (hr)		0.		¯	{	4-64
	b035	Rotational direction restriction	00 (enabling both forward and reverse rotations), 01 (enabling		00		¯	¯	4-7
			only forward rotation), 02 (enabling only reverse rotation)
	b036	Reduced voltage start selection	0 (minimum reduced voltage start time) to 255 (maximum		6		¯	{	4-42
Others			reduced voltage start time)
	b037	Function code display restriction	00 (full display), 01 (function-specific display), 02 (user setting),		04		¯	{	4-76
			03 (data comparison display), 04 (basic display)
	b038	Initial-screen selection	00 (screen displayed when the STR key was pressed last), 01		01		¯	{	4-78
			(d001), 02 (d002), 03 (d003), 04 (d007), 05 (F001)
	b039	Automatic user-parameter	00 (disabling), 01 (enabling)		00		¯	{	4-79
		setting function enable
	b040	Torque limit selection	00 (quadrant-specific setting), 01 (switching by terminal), 02		00		¯	{
			(analog input), 03 (option 1), 04 (option 2)
	b041	Torque limit (1) (forward-driving	0. to 200. (%), no (disabling torque limitation)		150.		¯	{
		in 4-quadrant mode)
limitation	b042	Torque limit (2)	0. to 200. (%), no (disabling torque limitation)		150.
		(reverse-regenerating in					¯	{	4-92
		4-quadrant mode)
Torque	b043	Torque limit (3) (reverse-driving	0. to 200. (%), no (disabling torque limitation)		150.		¯	{
		in 4-quadrant mode)
	b044	Torque limit (4)	0. to 200. (%), no (disabling torque limitation)		150.
		(forward-regenerating in					¯	{
		4-quadrant mode)
	b045	Torque limit LADSTOP enable	00 (disabling), 01 (enabling)		00		¯	{	4-94
	b046	Reverse Run protection enable	00 (disabling), 01 (enabling)		00		¯	{	4-93
power	b050	Controller deceleration and stop	00 (disabling), 01 (nonstop deceleration to stop), 02 (DC voltage		00		¯	¯
		on power loss	constant control, with resume), 03 ( without resume)
momentaryatoperation failure	b051	DC bus voltage trigger level	0.0 to 999.9, 1000. (V)		0.0		¯	¯
		during power loss
	b052	Over-voltage threshold during	0.0 to 999.9, 1000. (V)		0.0		¯	¯
		power loss
	b053	Deceleration time setting during	0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)		1.00		¯	¯	4-83
		power loss
	b054	Initial output frequency decrease	0.00 to 10.00 (Hz)		0.00		¯	¯
		during power loss
stop	b055	Proportional gain setting for	0.00 to 2.55		0.20		{	{
		nonstop operation at power loss
Non-
	b056	Integral time setting for nonstop	0.000 to 9.999 /10.00 to 65.53 (s)		0.100		{	{
		operation at power loss
	b060	Maximum-limit level of window	0. to 100. (lower limit : b061 + b062 / 2) (%)		100		{	{
		comparators O
	b061	Minimum-limit level of window	0. to 100. (lower limit : b060 - b062 / 2) (%)		0		{	{
		comparators O
	b062	Hysteresis width of window	0. to 10. (lower limit : b061 - b062 / 2) (%)		0		{	{
		comparators O
	b063	Maximum-limit level of window	0. to 100. (lower limit : b064 + b066 / 2) (%)		100		{	{
		comparators OI
comparator	b064	Minimum-limit level of window	0. to 100. (lower limit : b063 - b066 / 2) (%)		0		{	{
		comparators OI							4-71
	b065	Hysteresis width of window	0. to 10. (lower limit : b063 - b064 / 2) (%)		0		{	{
		comparators OI
Window	b066	Maximum-limit level of window	-100. to 100. (lower limit : b067 + b068 / 2) (%)		100		{	{
		Minimum-limit level of window
		comparators OI
	b067	comparators O/OI/O2	-100. to 100. (lower limit : b066 - b068 / 2) (%)		0		{	{
	b068	Hysteresis width of window	0. to 10. (lower limit : b066 - b067 / 2) (%)		0		{	{
		comparators O/OI/O2
	b070	Operation level at O	0. to 100. (%) or "no" (ignore)		no		¯	{
		disconnection
	b071	Operation level at OI	0. to 100. (%) or "no" (ignore)		no		¯	{
		disconnection
	b072	Operation level at O2	-100. to 100. (%) or "no" (ignore)		no		¯	{
		disconnection

8 - 7