Register Descriptions

13.4.7.1.101000BASE-T Control Register GCON (09d; R/W)

Table 13-28. 1000BASE-T Control Register Bit Description

Bit(s)

Field

 

Description

Mode

HW Rst

SW Rst

 

 

 

 

 

 

7:0

Reserved

Reserved. Should be set to 00000000b.

R/W

0b

0b

 

 

 

 

 

 

 

 

 

1b

= Advertise.

 

 

 

 

 

0b

= Not advertised.

 

 

 

 

 

82544GC/EI only:

R/W

0b

Retain

8

1000BASE-T Half

Bit 8 = ANEG[2].

Duplex

82541xx and 82547GI/EI only:

 

ANEG[2]

 

 

 

 

 

 

1b

= DTE is 1000BASE-T capable.

 

 

 

 

 

0b

= DTE is not 1000BASE-T capable.

 

 

 

 

 

This bit is used by Smart Negotiation.

 

 

 

 

 

 

 

 

 

 

 

 

1b

= Advertise.

 

 

 

 

 

0b

= Not advertised.

 

 

 

 

 

82544GC/EI only:

 

 

 

 

1000BASE-T Full

Bit 9 = ANEG[3].

R/W

1b

Retain

9

82541xx and 82547GI/EI only:

Duplex

1b = DTE is 1000BASE-T full duplex

 

ANEG[3]

 

 

 

 

 

 

capable.

 

 

 

 

 

0b = DTE is not 1000BASE-T full duplex

 

 

 

 

 

capable. This bit is used by Smart

 

 

 

 

 

Negotiation (see Note 3).

 

 

 

 

 

 

 

 

 

 

 

 

1b

= Prefer multi-port device

 

 

 

 

 

(MASTER).

 

 

 

10

Port Type

0b = Prefer single port device (SLAVE)1.

R/W

1b2

Retain

82544GC/EI only:

 

ANEG[0]

 

 

 

 

 

 

 

Bit 10 =!ANEG[0].

 

 

 

 

 

Bit 10 is ignored if bit 12 = 1b.

 

 

 

 

 

 

 

 

 

 

 

 

1b

= Manual configure as MASTER3.

 

 

 

 

MASTER/SLAVE

0b

= Manual configure as SLAVE3.

R/W

1b2

Retain

11

82544GC/EI only:

Configuration Value

 

ANEG[0]

 

 

Bit 11 =!ANEG[0].

 

 

 

 

 

 

 

 

 

Bit 11 is ignored if bit 12 = 0b.

 

 

 

 

 

 

 

 

 

 

 

 

1b

= Manual MASTER/SLAVE

 

 

 

 

MASTER/SLAVE

configuration.

 

1b2

 

12

0b

= Automatic MASTER/SLAVE

R/W

Retain

Manual Configuration

configuration.

 

ANEG[1]

 

 

Enable

 

 

 

82544GC/EI only:

 

 

 

 

 

 

 

 

 

 

Bit 12 =!ANEG[1].

 

 

 

 

 

 

 

 

 

 

Software Developer’s Manual

257

Page 271
Image 271
Intel PCI-X, Intel Gigabit Ethernet Controllers manual ANEG0, Master/Slave, ANEG1