Toshiba VF-A7 instruction manual Basic parameter list

[Basic parameter list]

No.	Title	Function			Adjustment range				Default	Reference
									setting	section
1		Automatic	: Manual acceleration/deceleration							5.1.1
		acceleration/deceleration	: Automatic acceleration/deceleration
			:－(0 is always displayed.)
2		Automatic V/f mode setting	: Automatic torque boost + auto-tuning							5.2
			: Sensorless vector control (speed) + auto-tuning
			: Automatic energy-saving + auto-tuning
			: Terminal block enabled
3		Operation command mode	: Operating panel enabled							5.3
			: Common serial communication option enabled						
		selection	: Serial communication RS485 enabled
			: Communication add-on cassette option enabled
			: VI (voltage input)/II (current input)
			: RR (volume/voltage input)
			: RX (voltage input)
			: RX2 (voltage input) (optional)
4		Speed setting mode	: Operating panel input							5.3
			: Binary/BCD input(optional)						
		Selection	: Common serial communication option(FA01)
			: Serial communication RS485(FA05)
			: Communication add-on cassette option(FA07)
			: Up-down frequency
			: Pulse input #1 (optional)
5		FM terminal meter selection	～							5.4
6		FM terminal meter	－						－	5.4
		adjustment
			:－
			: 50Hz standard setting
			: 60Hz standard setting
7		Standard setting mode	: Factory default setting							5.5
			: Trip clear						
		selection
			: Clearing accumulating operation time
			: Initialization of type form information
			: Memorization of user-defined parameters
			: Reset of user-defined parameters
8		Forward/reverse selection	: Forward,							5.6
		(At panel control only)	: Reverse
9		Acceleration time #1	()～ [s]						See J-28	5.1.2
10		Deceleration time #1	()～ [s]						See J-28	5.1.2
11		Maximum frequency	～ [Hz]							5.7
12		Upper limit frequency	～ [Hz]							5.8
13		Lower limit frequency	～ [Hz]							5.8
14		Base frequency #1	～ [Hz]							5.9
			: Constant torque
			: Variable torque mode
			: Automatic torque boost
			: Sensorless vector control (speed)
15		Motor control mode	: Automatic torque boost + automatic energy-saving							5.10
		selection	: Sensorless vector control (speed) + automatic energy-saving
			: V/f 5-points setting
			:Sensorless vector control (speed/torque switching)
			: PG feedback vector control (speed/torque switching)
			: PG feedback vector control (speed/position switching)
16		Manual torque boost	～ [%]						See J-28	5.12
			Setting		Type	Overload protection	Overload stall
						protect	not	stall
					Standard	protect	stall
		Selection of electronic			motor	not protect	not	stall
17		thermal protection				not protect	stall			5.13
		characteristics		VF motor		protect	not	stall
						protect	stall
					(special
						not protect	not	stall
					motor)
						not protect	stall
18		Preset-speed # 1	～ [Hz]						
19		Preset-speed # 2	～ [Hz]						
20		Preset-speed # 3	～ [Hz]							5.14
21		Preset-speed # 4	～ [Hz]						
22		Preset-speed # 5	～ [Hz]						
23		Preset-speed # 6	～ [Hz]						
24		Preset-speed # 7	～ [Hz]						
25		Extended parameter	Setting of extended						－	4.1.2
	～
26		Automatic edit function	To search		parameters different from default value.				－	4.1.2

D-3