Toshiba VF-A7 instruction manual , Speed setting, Panel stop pattern

3) Start and stop (forward run, reverse run, free-run stop) with

the operating panel and to set the operation frequency by external signals

Title	Function	Set value
	Operation command	(operating panel)
	mode selection
	Speed setting	(VI/II)
		(RR)
	mode selection
		(RX)
	Panel stop pattern	(Coast stop)

[Start/stop]: Press the RUN STOP key on the

operating panel.

To switch between forward run and reverse run, use the forward/reverse run selection .

[Speed command]: By means of external signals

(1)VI: 0 to +10 Vdc (0 to +5 Vdc) II: 4 to 20 mAdc

(2)RR: Volume / 0 to +10 Vdc (0 to +5 Vdc)

(3)RX: 0 to +/-10 Vdc (0 to +/-5 Vdc)

Power	R/L1	U/T1
	S/L2	V/T2
supply
	T/L3	W/T3
		F
		R
	Operating panel
		ST
	G/E	CC
	CC	RX VI II RR PP

Motor

IM

The inverter is shipped with these terminals shorted.

※Other speed setting

: RX2 (voltage input) (optional)*

: 12/16-bit binary input (optional)*

: Serial communication (optional)*

: Serial communication RS485

: Communication add-on(optional)*

: Up-down frequency

: Pulse input (optional)*

＊For the setting to be made when using an asterisked optional device as an input device, refer to the instruction manual for the input device used.

＋	③０～±１０Ｖｄｃ
―	（０～± ５Ｖｄｃ）
＋	①０～＋１０Ｖｄｃ
―	（０～＋ ５Ｖｄｃ）
＋
	①４～２０ｍＡｄｃ
―

②External volume control

4) Start and stop (forward run, reverse run, free-run stop) and

to set the operation frequency by means of external signals

Title	Function	Set value
	Operation command	(Terminal input)
	mode selection
	Speed setting	(VI/II)
		(RR)
	mode selection
		(RX)

[Start/stop]: Connection and disconnection of terminals F and CC/terminals R and CC.

[Speed command]: By means of external signals

(1)VI: 0 to +10Vdc (0 to +5Vdc)/II: 4 to 20mAdc

(2)RR: Volume/0 to +10 Vdc (0 to +5Vdc)

(3)RX: 0 to +/-10 Vdc (0 to +/-5Vdc)

Power	R/L1	U/T1
	S/L2	V/T2
supply	T/L3	W/T3
		F
		R
	Control panel
		ST
	G/E	CC
	CC RX	VI II RR PP

Motor

IM

Forward run if ON Slowdown stop if OFF Reverse run if ON Slowdown stop if OFF Standby if ON

Free-run stop if OFF

As for the action the motor takes when both the terminals F and R are connected at the same time, you can make a selection between reverse run and a stop.

=> Refer to 6.2.2

※Other speed setting

: RX2 (voltage input) (optional)*

: 12/16-bit binary input (optional)*

: Serial communication (optional)*

: Serial communication RS485

＋	③０～±１０Ｖｄｃ
―	（０～± ５Ｖｄｃ）
＋	①０～＋１０Ｖｄｃ
―	（０～＋ ５Ｖｄｃ）
＋	①４～２０ｍＡｄｃ
―

②External volume control

: Communication add-on(optional)*

: Up-down frequency

: Pulse input (optional)*

＊For the setting to be made when using an asterisked optional device as an input device, refer to the instruction manual for the input device used.

E-9