Toshiba VF-A7 instruction manual Speed/torque reference gain/bias setup 1/2

J-6

[7] Speed/torque reference gain/bias setup (1/2)					Sensorless vector/vector with sensor (●valid, －:invalid)
Title	Communi	Function	Adjustment range	Min. unit (panel/	Default	Write during	Vector control			V/f	Reference
							Speed	Torque	Position
	cation No			communication)	setting	running	control	control	control	Constant	section
			0: 
			1: 
	0200	Reference priority selection	2:  priority (*1)	－	0	Enabled	●/●	－	－	●	6.6.1
			3:  priority (*2)
			4: / switching
	0201	VI/II reference point #1	0～100 [%]	1/0.01	20.0	Enabled	●/●	●/●	－	●	7.3.2
	0202	VI/II reference point #1 frequency	0.0～ [Hz]	0.01/0.01	0. 0	Enabled	●/●	●/●	－	●	7.3.2
	0203	VI/II reference point #2	0～100 [%]	1/0.01	100	Enabled	●/●	●/●	－	●	7.3.2
	0204	VI/II reference point #2 frequency	0.0～ [Hz]	0.01/0.01	80.0	Enabled	●/●	－	－	●	7.3.2
	0205	VI/II reference point #1 rate	-250～250 [%] (For torque control, etc.)	1/0.01	0	Enabled	●/●	●/●	－	－	6.21.1
	0206	VI/II reference point #2 rate	-250～250 [%] (For torque control, etc.)	1/0.01	100	Enabled	●/●	●/●	－	－	6.21.1
	0207	Speed setting mode selection #2	Same as  (1 to 11)	－	1	Enabled	●/●	－	－	●	6.61
	0208	/switching frequency	0.1～ [Hz]	0.01/0.01	1.0	Enabled	●/●	－	－	●	6.6.1
	0209	Analog input filter	0(Disabled) to 3(Max. filter capacity)	－	0	Enabled	●/●	●/●	－	●	7.2.4
	0210	RR reference point #1	0～100 [%]	1/0.01	0	Enabled	●/●	●/●	－	●	7.3.1
	0211	RR reference point #1 frequency	0.0～ [Hz]	0.01/0.01	0.0	Enabled	●/●	－	－	●	7.3.1
	0212	RR reference point #2	0～100 [%]	1/0.01	100	Enabled	●/●	●/●	－	●	7.3.1
	0213	RR reference point #2 frequency	0.0～ [Hz]	0.01/0.01	80.0	Enabled	●/●	－	－	●	7.3.1
	0214	RR reference point #1 rate	0～250 [%] (For torque control, etc.)	1/0.01	0	Enabled	●/●	●/●	－	－	6.21.1
	0215	RR reference point #2 rate	0～250 [%] (For torque control, etc.)	1/0.01	100	Enabled	●/●	●/●	－	－	6.21.1
	0216	RX reference point #1	-100～100 [%]	1/0.01	0	Enabled	●/●	●/●	－	●	7.3.3
	0217	RX reference point #1 frequency	-～ [Hz] (*3)	0.01/0.01	0.0	Enabled	●/●	－	－	●	7.3.3
	0218	RX reference point #2	-100～100 [%]	1/0.01	100	Enabled	●/●	●/●	－	●	7.3.3
	0219	RX reference point #2 frequency	-～ [Hz] (*3)	0.01/0.01	80.0	Enabled	●/●	－	－	●	7.3.3
	0220	RX reference point #1 rate	0～250 [%] (For torque control, etc.)	1/0.01	0	Enabled	●/●	●/●	－	－	6.21.1
	0221	RX reference point #2 rate	0～250 [%] (For torque control, etc.)	1/0.01	100	Enabled	●/●	●/●	－	－	6.21.1
	0222	RX2 reference point #1	-100～100 [%]	1/0.01	0	Enabled	●/●	●/●	－	●	※
	0223	RX2 reference point #1 frequency	-～ [Hz] (*3)	0.01/0.01	0.0	Enabled	●/●	－	－	●	※
	0224	RX2 reference point #2	-100～100 [%]	1/0.01	100	Enabled	●/●	●/●	－	●	※
	0225	RX2 reference point #2 frequency	-～ [Hz] (*3)	0.01/0.01	80.0	Enabled	●/●	－	－	●	※
	0226	RX2 reference point #1 rate	-250～250 [%] (For torque control, etc.)	1/0.01	0	Enabled	●/●	●/●	－	●	※
	0227	RX2 reference point #2 rate	-250～250 [%] (For torque control, etc.)	1/0.01	100	Enabled	●/●	●/●	－	●	※

(*1): When setup frequency(signal set up by ) is or more, signal set up by is accepted, When setup frequency is lower than , the inverter runs under the signal of .

(*2): When setup frequency(signal set up by ) is or more, signal set up by is accepted, When setup frequency is lower than , the inverter runs under the signal of .

(*3): Adjustment range is -327.68～327.67 [Hz] in case of 16-bit access.

※(Reference section): Refer to the inverter's individual manual.