Bosch Appliances 3.5 manual Clause / Requirement

Praesideo 3.5 Installation and User Instructions EN54-16: 2008

en 51

Clause / Requirement		Compliance	Signature
13.8.3	Mandatory indications on an alphanumeric display	If the Praesideo system enters the voice alarm condition the
shall be legible for at least one hour following the display of		display of the network controller will automatically show the
a new indication of the voice alarm condition and at least		‘Emergency’ menu. This indication stays on as long as the
5 minutes for fault or disablement conditions, at 0,8 m		system is in the voice alarm condition (i.e. until the voice
distance, in ambient light intensities from 5 to 500 lux, at		alarm condition is reset).
any angle from the normal to the plane of the display up to		If the Praesideo system enters the fault warning condition
• 22.5º when viewed from each side, and
• 15º when viewed from above and below.		the display of the network controller will automatically show
		the ‘Faults’ menu with the current number of active faults.
		This indication stays on until either the rotary knob of the
		network controller is used to navigate through the menu, or
		the system enters the voice alarm condition. The ‘Faults’
		menu will always be present in the Network Controller
		menu. Individual faults are present in this ‘Faults’ menu until
		they are reset or until they are overwritten by newer faults
		The menu can show up to 200 individual faults after which
		the oldest faults are deleted when new faults occur.
		The display of the Network Controller complies with the
		legibility demands of this clause.
13.9 Indication colors		Praesideo is compliant.
13.9.1	The colors of the general and specific indications
from light emitting indicators shall be
a red for indications of voice alarms;		The system status LED of Praesideo call stations is on
		(red) when the system is in the voice alarm condition. The
		installer must connect a red light emitting indicator to an
		‘Emergency alarm indicator’ output contact of the
		Praesideo system. The key of a call station keypad kit shall
		be configured to the action ‘Zone status’. The installer must
		connect a red LED to the appropriate control output
		belonging to this key.
b yellow for indications of		The Power/Fault LED of Praesideo call stations is yellow
1	fault warnings, and	(on or flashing) when the system is in the fault warning
		condition. The installer must connect a yellow light emitting
2	disablements, or	indicator to the ‘Fault alarm indicator’ output contact (or
		another output contact configured for this function). A call
		station key indicator lights up yellow when the key is
		configured to the action ‘Reset fault’ or ‘Ack and reset’ and
		the system enters the fault warning condition.
		Disablement indication is not available in the Praesideo
		system since Praesideo does not support the optional
		disablement condition.
c green for the indication that the VACIE is supplied with		All light emitting indicators of the Praesideo system that
power.		indicate power supply are green.
NOTE - Where voice alarm automatic message status
indicators are provided, it may be advantageous to indicate
the difference between evacuation and alert messages. In
this case, red will be used for emergency messages and
yellow may be used for alert messages.
13.9.2	The use of different colors is not necessary for	The alphanumeric displays used in the Praesideo system
indications on alphanumeric displays. However, if different		do not use different colors for indications.
colors are used for different indications, the colors used
shall be as specified in 13.9.1.

13.10 Audible indications

13.10.1Audible indicators shall be part of the VACIE. The same device may be used for voice alarm zone activated and fault warning indications.

13.10.2The minimum sound pressure level, measured under anechoic conditions at a distance of 1 m, with any access door(s) on the VACIE closed, shall be

• 60 dBA for the voice alarm condition, and

• 50 dBA for the fault warning condition.

Praesideo is compliant.

The installer must connect buzzers to output contacts configured as ‘Emergency alarm buzzer’ or ‘Fault alarm buzzer’. The installer may decide to connect both the voice alarm activated output contact as well as the fault warning condition activated output contact in parallel to the same buzzer.

The installer must connect the buzzer, provided with Praesideo, that complies with this clause.

Bosch Security Systems 2011-02