Power Save Configuration Registers | Epson S1D13504 specs

Page 102	Epson Research and Development
	Vancouver Design Center

8.2.6 Power Save Configuration Registers

Power Save Configuration Register

REG[1Ah]

RW

LCD Power

Suspend

Suspend

Software

n/a

n/a

n/a

n/a

Refresh

Refresh

Suspend

Disable

Select Bit 1

Select Bit 0

Mode Enable

bit 3

LCD Power Disable

When this bit = 1 the LCDPWR output is directly forced to the Off state. The LCDPWR “On/Off”

state is configured by MD10 at the rising edge of RESET#. When this bit = 0 the LCDPWR output

is controlled by the panel on/off sequencing logic. See Table 5-8: “Summary of Power On / Reset

Options,” on page 31.

bits 2-1

Suspend Refresh Select Bits [1:0]

These bits specify the type of DRAM refresh to use in Suspend mode.

Table 8-10: Suspend Refresh Selection

Suspend Refresh Select Bits [1:0]

DRAM Refresh Type

00

CBR Refresh

01

Self-Refresh

1x

No Refresh

Note

These bits should not be changed when suspend mode is enabled.

bit 0

Software Suspend Mode Enable

When this bit = 1 software suspend mode is enabled. When this bit = 0 software suspend mode is disabled.

8.2.7 Miscellaneous Registers

Miscellaneous Disable Register
REG[1Bh]								RW

Host Interface	n/a		n/a	n/a	n/a	n/a	n/a	Half Frame
Disable								Buffer Disable
bit 7		Host Interface Disable
		This bit must be programmed to 0 to enable the Host Interface. This bit goes high on reset. When
		this bit is high, all memory and all registers except REG[1Ah] (read-only), REG[28h] through
		REG[2Fh], and REG[1Bh] are inaccessible.

S1D13504	Hardware Functional Specification
X19A-A-002-18	Issue Date: 01/01/30

Image 108

Epson S1D13504 manual Power Save Configuration Registers, Miscellaneous Registers, Miscellaneous Disable Register

Contents

Technical Manual Document Number X19A-Q-002-14 This page Left Blank Customer Support Information This page Left Blank Power Down Modes General Purpose IO pinsMemory Interface CPU Interface CPU Ramdac Hardware Functional Specification Document Number X19A-A-002-18 X19A-A-002-18 Issue Date 01/01/30 Table of Contents Registers Display Configuration 116 Power Save Modes 128Display Buffer Clocking 119 This page Left Blank List of Tables Vancouver Design Center List of Figures Vancouver Design Center Introduction ScopeOverview Description Features Memory InterfaceCPU Interface Display Support Display Modes Clock SourceMiscellaneous Package and Pin Typical System Implementation Diagrams LCD Management MC68000 Typical System Diagram Generic Bus, 1Mx16 FPM/EDO-DRAM Functional Block Diagram Block DescriptionFunctional Block Descriptions Host Interface Memory Controller Power Save Look-Up TableLCD Interface Pinout Diagram for S1D13504F00A Pin OutPackage type 128 pin surface mount QFP15 Pinout Diagram for S1D13504F01A Package type 128 pin surface mount TQFP15 Pinout Diagram for S1D13504F02A Package type 144 pin surface mount QFP20 Pin Description KeyAB0 TS2 CS# BusclkBS# RD/WR# RESET# WAIT# TS2 LCAS# CO1 UCAS# CO1WE# CO1 RAS# CO1 MA9 TS1 Clock Input LCD Interface Pin Descriptions CRT and External Ramdac Interface CRT and Ramdac Interface Pin Descriptions HrtcVrtc BLANK# CN3 Power Supply Pin # Pin Name Type Driver Description F00A F02A F01A Summary of Configuration Options Multiple Function Pin Mapping S1D13504 SH-3 MC68K Bus Generic MPU Pin NamesAsym 256Kx16 Asym 1Mx16 11 LCD, CRT, Ramdac Interface Pin Mapping C. Characteristics Symbol Parameter Rating UnitsSymbol Parameter Condition Min Typ Max Units Low Level Output Voltage Output Leakage CurrentOutput Pin Capacitance Bidirectional Pin Capacitance CPU Interface Timing 1 SH-3 Interface Timing RD/WR# BS#WAIT# Symbol Parameter Min Max Units 2 MC68K Bus 1 Interface Timing e.g. MC68000 AS# UDS# LDS#T13 T14 T15 D150read AS# high setup to CLK AS# high to DTACK# high impedanceD150 hold from falling edge of DTACK# write cycle D150 valid to DTACK# falling edge read cycle 3 MC68K Bus 2 Interface Timing e.g. MC68030 A200 SIZ10 M/R#AS# DS# T13 T14 T15 D3116 hold from falling edge of DSACK1# write cycle D3116 valid to DSACK1# falling edge read cycle Generic MPU Interface Synchronous Timing BclkA200 RD0#,RD1# WE0#,WE1# Hi-Z Low write cycle D150 hold from WE0#, WE1# high write cycle Generic MPU Interface Asynchronous Timing A200 ValidHi-Z Valid T10 D150read T82 Symbol Parameter Min Typ Max Units Clock Input Requirements Memory Interface Timing EDO-DRAM Read Timing RAS# CAS# EDO Dram Read Timing EDO-DRAM Write Timing RAS# CAS# WE# T14 Write Data setup time 45 t1 T15 Write Data hold time 55 t1 + CAS# precharge time 45 t1 EDO-DRAM Read-Write Timing EDO-DRAM Read-Write Timing EDO Dram Read-Write Timing EDO-DRAM CAS Before RAS Refresh Timing 10 EDO-DRAM CAS Before RAS Refresh Timing EDO-DRAM Self-Refresh Timing 11 EDO-DRAM Self-Refresh Timing FPM-DRAM Read Timing 12 FPM-DRAM Read Timing 12 FPM Dram Read Timing FPM-DRAM Write Timing 13 FPM-DRAM Write Timing T14 Write Data setup time 45 t1 T15 Write Data hold time FPM-DRAM Read-Write Timing 14 FPM-DRAM Read-Write Timing 45 t1 S1D13504 FPM-DRAM CAS# Before RAS# Refresh Timing RAS# precharge time REG22h bits 32 = 01 or 45 t1 FPM-DRAM Self-Refresh Timing 16 FPM-DRAM CBR Self-Refresh Timing Display Interface Power-On/Reset Timing Fpframe active Suspend Timing Mclk Single Monochrome 4-Bit Panel Timing VDP =Vndp = HDP = Sync Timing Data Timing Single Monochrome 8-Bit Panel Timing VDPVndp HDP UD30, LD30 setup to Fpshift falling edge UD30, LD30 hold to Fpshift falling edge= REG05h bits 40 + 1*8 23 Ts = REG05h bits 40 + 1*8 14 Ts Single Color 4-Bit Panel Timing 23 Single Color 4-Bit Panel Timing = REG04h bits 60+1*8 1 Ts = REG05h bits 40 + 1*8 26 Ts= REG05h bits 40 + 1*8 17 Ts Single Color 8-Bit Panel Timing Format 25 Single Color 8-Bit Panel Timing Format UD30, LD30 setup to FPSHIFT2 rising, Fpshift falling edge Fpline pulse width Fpline periodFPSHIFT2 falling edge to Fpline rising edge FPSHIFT2, Fpshift pulse width high 27 Single Color 8-Bit Panel Timing Format T1min = t3min 9Ts Single Color 16-Bit Panel Timing VDP Vndp LINE1 LINE2 LINE3 LINE4 LINE479 LINE480 HDP Hndp UD70, LD70 setup to Fpshift falling edge UD70, LD70 hold to Fpshift falling edge Dual Monochrome 8-Bit Panel Timing Fpshift UD3 UD2 UD1 UD0 LD3 LD2 LD1 LD0 = REG05h bits 40 + 1*8 8 Ts Dual Color 8-Bit Panel Timing 33 Dual Color 8-Bit Panel Timing = REG05h bits 40 + 1*8 9 Ts Dual Color 16-Bit Panel Timing 35 Dual Color 16-Bit Panel Timing UD70 LD70 12 16-Bit TFT Panel Timing = Vertical Display Period = REG09h bits 10, REG08h bits 70 + 38 TFT A.C. Timing = REG04h bits 60+1*8 + REG05h bits 40+1*8 Ts = REG07h bits 30+1*8 Ts= REG0Ch bits 20+1 lines CRT Timing 39 CRT Timing 40 CRT A.C. Timing Dacclk period External Ramdac Read / Write Timing ReadWrite DACWR# pulse width low Registers Register MappingRegister Descriptions Revision Code Register Memory Configuration Registers Memory Configuration RegisterTime/256 Cycles Panel/Monitor Configuration Registers Panel Type RegisterMOD Rate Register REG03h MOD Rate Bit Horizontal Display Width Register Horizontal Non-Display Period RegisterHRTC/FPLINE Start Position Register HRTC/FPLINE Pulse Width Register Vertical Display Height RegisterHrtc Fpline Vertical Non-Display Period Register VRTC/FPFRAME Start Position RegisterVrtc Fpframe VRTC/FPFRAME Pulse Width Register REG0ChFpframe Vrtc Vrtc Polarity Display Configuration Registers Display Mode RegisterSimultaneous Display Option Select Bits Even Scan Only Number of Bits-Per-Pixel Selection Screen 1 Line Compare Register Screen 1 Display Start Address Register Screen 2 Display Start Address Register 0 RW Screen 2 Display Start Address RegisterMemory Address Offset Register Clock Configuration Register Clock Configuration RegisterPixel Panning Register Number of Bits-Per-Pixel Screen 2 Pixel Panning Bits Used Power Save Configuration Registers Power Save Configuration RegisterMiscellaneous Disable Register Miscellaneous Registers MD Configuration Readback Register Gpio Configuration RegisterREG1Dh MD15 MD14 MD13 MD12 MD11 MD10 MD9 MD8 Vancouver Design Center REG1Fh GPIO11 Pin GPIO10 Pin GPIO9 Pin GPIO8 Pin IO Config Gpio Status / Control Register Gpio Status / Control Register REG21hGPO GPIO11 Pin GPIO10 Pin GPIO9 Pin GPIO8 Pin Control IO Status Performance Enhancement Register REG22h EDO Read RC Timing RAS# toREG22h Bits Minimum Random Cycle Width t RC RAS# to CAS# Delay tRCD Optimal Dram TimingREG22h Bit RAS# Precharge Width t RP RGB Index Bits Look-Up Table Access Pointer Sequence Look-Up Table RegistersLook-Up Table Address Register Look-Up Table Data Register Look-Up Table Bank Select RegisterREG26h LUT Data Bit REG27h Red Bank Blue Bank Green Bank Select Bit Ramdac Read Mode Address Register Ramdac Write Mode Address RegisterExternal Ramdac Control Registers Ramdac Pixel Read Mask Register Ramdac Palette Data Register REG2Eh or REG2Fh Display Buffer 512K byte Memory AB200 Image Buffer Half Frame Buffer Display Configuration Display Mode Data Format 15/16 Bit-Per-Pixel Format Memory Organization Image Manipulation DisplayImage Buffer Clocking Maximum Mclk Pclk RatiosDisplay type Maximum Pclk Allowed Bpp 16 bpp Frame Rate Calculation = PclkSpeed Grade Bpp Clock Hndpt s Panel MHz FPM-DRAM Bit-Per-Pixel Mode Display Mode Bit Wide Look-Up TableLook-Up Table Architecture Gray Shade Display Modes Bit-Per-Pixel Mode Bit-Per-Pixel Color Mode Color Display Modes Bank Selected Bank Entry Bit Red data output Logic Red Look-Up Table 0000 0001 0010 0011 0100 0101 Entry 0110 Color Data Format Red Look-Up Table Power Save Modes Hardware SuspendSoftware Suspend Power Save Mode Function Summary Pin States in Power Save ModesPower Save Mode PSM Pin State Pins Normal Software Hardware Active Suspend Mechanical Data 14.1 QFP15-128 S1D13504F00AQFP15 128 pin Unit mm TQFP15-128 S1D13504F01A TQFP15 128 pin Unit mm±0.2 QFP20-144 S1D13504F02A QFP20 144 pin Unit mm125 Programming Notes and Examples Document Number X19A-G-002-07 This page Left Blank LCD Power Sequencing and Power Save Modes Introduction Programming the S1D13504 RegistersAdvanced Techniques CRT Considerations Identifying the S1D13504 Hardware Abstraction Layer HALSample Code Appendix a Supported Panel Values Initializing the S1D13504 Registers This page Left Blank Introduction Programming the S1D13504 Registers 2 REG22 bits 7-2 Performance Enhancement Register3 REG02 bit 1 Dual/Single Panel Type 4 REG1B bit 0 Half Frame Buffer Disable 5 REG23 Display FifoRegister Initialization Initialization Sequence Initialization Example Initializing the S1D13504 RegistersOperation Description Re-Programming Registers Disabling the Half Frame Buffer Sequence Display Buffer Location BitPixel Bit Memory Organization for Eight Bit-per-pixel 256 Colors Bit Red Bit Green Bit Blue Bit Memory Organization for 15 Bit-per-pixel 32768 Colors Memory Organization for 16 Bit-per-pixel 65536 ColorsBit Reserved Red Bit Green Bit Blue Bit Look-Up Table LUT REG24h Look-Up Table Address Register Read/WriteREG26h Look-Up Table Data Register Read/Write REG27h Look-Up Table Bank Register Read/Write Bank Select Bits Look-Up Table Configurations Look-Up Table OrganizationBank Recommended LUT Values for 1 bpp Color Mode Recommended LUT Values for 2 bpp Color ModeColor Modes Address Red Green Blue 11 Recommended LUT Values For 8 bpp Color Mode 12 Examples of 256 Pixel Colors Using Linear LUT Gray Shade Modes13 Recommended LUT Values for 1 bpp Gray Shades Pixel Value Color 14 Recommended LUT Values for 2 bpp Gray Shades 15 Recommended LUT Values for 8 bpp Gray ShadeLUT Address Green LUT Data Bpp Gray Shade Advanced Technique s Virtual Display Registers ExamplesREG16h Memory Address Offset Register REG17h Memory Address Offset Register Panning and Scrolling Number of Pixels Panned Using Start Address Active Pixel Pan Bits Example 4 Panning Right and Left Split Screen REG0E Screen 1 Line Compare RegisterLine Compare Bit REG0F Screen 1 Line Compare Register REG13h Screen 2 Display Start Address Register REG14h Screen 2 Display Start Address RegisterREG15h Screen 2 Display Start Address Register LCD Power Sequencing and Power Save Modes Introduction to LCD Power SequencingIntroduction to Power Save Modes Display Mode Register Suspend Enable Sequence Shortening the 128 Frame delay using Software SuspendShortening the 128 Frame Delay using Hardware SUSPEND# Suspend Sequencing Suspend Disable Sequence LCD Enable/Disable Sequencing Reg0D bitLCD Enable / Disable using Power Save Modes LCD Enable / Disable using Manual Control CRT Considerations IntroductionCRT Only Ramdac Register Mapping for Little/Big-Endian Simultaneous Display Related Register Data for CRT Only Address Address Related register data for Simultaneous Display Register 640X480@75Hz 640X480@60Hz Identifying the S1D13504 Hardware Abstraction Layer HAL API for 13504HALInitialization Int seDeRegisterDeviceint device Int seGetIdint device, Byte *pId Int seInitHalvoid Int seSetInitint device Int seValidRegisteredDeviceint deviceInt seValidStdDeviceint device Int seGetBitsPerPixelint device, Byte *pBitsPerPixel Int seGetBytesPerScanlineint device, int *pBytesInt seGetLastUsableByteint device, Dword *pLastByte Int seGetLinearDispAddrint device, Dword *pDispLogicalAddr Int seGetScreenSizeint device, int *width, int *height Int seReadDisplayByteint device, Dword offset, Byte *pByteInt seReadDisplayWordint device, Dword offset, Word *pWord Int seSetBitsPerPixelint device, Byte BitsPerPixel Int seSplitInitint device, Dword Scrn1Addr, Dword Scrn2Addr Int seVirtInitint device, int xVirt, long *yVirt Int seVirtMoveint device, Byte WhichScreen, int x, int y Vancouver Design Center Color Manipulation Int seGetDacint device, Byte *pDac Int seGetDacEntryint device, Byte index, Byte *pEntryInt seGetLutint device, Byte *pLut Int seGetLutEntryint device, Byte index, Byte *pEntry Int seSetDacint device, Byte *pDacInt seSetDacEntryint device, Byte index, Byte *pEntry Int seSetLutint device, Byte *pLut Int seSetLutEntryint device, Byte index, Byte *pEntry Int seDrawTextint device, char *fmt Int seGetcharvoid Int sePutcharint chInt sePutcint device, int ch Miscellaneous Int seDelayint device, Dword Seconds Int seSetPixelint device, int x, int y, Dword colorInt seSetRegint device, int index, Byte val Word seRotateByteLeftBYTE val, Byte bits Word seRotateByteRightBYTE val, Byte bits Sample code using 13504HAL API Sample Code Sample code without using 13504HAL API Vancouver Design Center Pclk To arrive at the frame rate closest to the desired Words Fifo Appendix a Supported Panel Values Supported Panel ValuesPassive Single Panel Passive Dual Panel TFT Panel TFT 16-Bit Register Single 01/02/02 Number of Bits/Pixel 13504CFG.EXE Configuration Program Document Number X19A-B-001-04 Vancouver Design Center X19A-B-001-04 Script Mode Interactive Mode 13504CFG.EXE Program Requirements This page Left Blank 13504CFG View Menu This page Left Blank 13504CFG.EXE Installation Program RequirementsUsage Script Mode Interactive Mode 13504CFG Menu Bar Making 13504CFG Menu Selections Files Menu View Menu 13504CFG Current Configuration Device Menu Panel Edit Panel Setup CRT Edit CRT Setup Advanced Memory Edit Advanced Memory Setup Power Management Edit Power Setup Lookup Table LUT Edit LUT Setup Setup Help Menu Comments Sample Program Messages This page Left Blank 13504SHOW Demonstration Program Document Number X19A-B-002-05 This page Left Blank 13504SHOW S1D13504 Supported Evaluation Platforms Error Too many devices registered Program Messages 13504SPLT Display Utility Document Number X19A-B-003-05 This page Left Blank 13504SPLT 13504SPLT Example Comments This page Left Blank 13504VIRT Display Utility Document Number X19A-B-004-05 S1D13504 13504VIRT Display Utility X19A-B-004-05 13504VIRT 13504VIRT Example Comments This page Left Blank 13504PLAY Diagnostic Utility Document Number X19A-B-005-05 This page Left Blank 13504PLAY Reads/writes the registers 13504PLAY Example Scripting Comments 13504BMP Demonstration Program Document Number X19A-B-006-04 This page Left Blank 13504BMP Program Messages 13504PWR Software Suspend Power Sequencing Utility Document Number X19A-B-007-04 X19A-B-007-04 Issue Date 01/02/01 13504PWR Selects software suspend Error Unknown command line argument This page Left Blank 13504DCFG Configuration Program Document Number X19A-B-008-02 This page Left Blank Table of Contents This page Left Blank List of Figures Clocks Tab Panel Tab This page Left Blank Installation 13504DCFGUsage 13504DCFG Configuration Tabs General Tab General Tab Memory Tab Memory Tab Clocks Tab Clocks Tab Clocks Tab ClkiLCD Mclkpclk CRT Mclkpclk Panel Tab Panel Tab Panel Tab STN/TFTHRTC/FPLINE VRTC/FPFRAME CRT Tab CRT Tab Defaults Tab Defaults TabSelect the default display device. Three display modes LCD Initializes the registers based on the default mode Registers Tab Registers Tab Miscellaneous Flags Tab Miscellaneous Flags Tab Saving to a File Resolution Frame Rate Hz Pclk MHz Supported Dram Types Comments Windows CE Display Drivers Document Number X19A-E-001-04 X19A-E-001-04 DIP Switch Program RequirementsExample Driver Builds Windows Version With this line Build For Cepc If CEPCDDIVGA2BPP Epson Research and Development Example Installation Installation for Hitachi D9000 and Etma ODOInstallation for Cepc Environment Comments This page Left Blank Wind River WindML v2.0 Display Drivers Document Number X19A-E-002-03 X19A-E-002-03 Issue Date 01/04/06 Wind River WindML v2.0 Display Drivers Building a WindML v2.0 Display Driver Make CPU=PENTIUM ugl Epson Research and Development This page Left Blank Wind River UGL v1.2 Display Drivers Document Number X19A-E-003-02 X19A-E-003-02 Wind River UGL v1.2 Display Drivers Building a UGL v1.2 Display Driver Epson Research and Development This page Left Blank Document Number X19A-G-004-06 S1D13504 X19A-G-004-06 Issue Date 01/02/02 Installation and Configuration Parts List Schematic Diagrams This page Left Blank S1D13504B00C Schematic Diagram 1 of 6 This page Left Blank Features Installation and Configuration Configuration DIP Switch SettingsJumper Settings Host Bus Selection LCD Signal Connector J6 LCD / Ramdac Interface Pin Mapping CPU / BUS Interface Connector Pinouts CPU/BUS Connector H1 PinoutConnector Comments Pin No CPU/BUS Connector H2 Pinout Host Bus Interface Pin Mapping DB150 D150 D3116 WE1# Technical Description ISA Bus Support Non-ISA Bus Support Dram SupportDecode Logic Clock Input Support Monochrome LCD Panel Support Color Passive LCD Panel SupportColor TFT LCD Panel Support External Cmos Ramdac Support Power Save Modes Core VDD Power SupplyIO VDD Power Supply Adjustable LCD Panel Negative Power Supply Schematic Notes 15 CPU/Bus Interface Header Strips Parts List Item # Qty/board Designation Part Value Description TIBPAL22V10-15BCNT Texas Instrument PAL 24 pin DIP package/socketed Schematic Diagrams S1D13504B00C Schematic Diagram 2 Rev.1.0 S1D13504B00C Schematic Diagram 4 Diagram 5 S1D13504B00C Schematic Diagram 6 This page Left Blank S5U13504-D9000 Document Number X19A-G-003-05 S5U13504-D9000 X19A-G-003-05 Issue Date 01/02/02 Introduction Features D9000 Specifics This page Left Blank S5U13504-D9000 Perspective View This page Left Blank Reference S1D13504 Color Graphics LCD Controller Display Buffer LCD Display Support LCD Connector Pinout LCD Interface Pin Mapping Adjustable LCD Bias Power Supply CRT Support Interface Signals Connector Pinout for Channel A6 and A7Interface Signals D9000 Specifics Connector Pinout for Channel A7 GNDDC12V Channel A7 Pin # Fpga Signal S1D13504 Signal SmZ Connectors Pinout for Channel A6 Channel A6 Pin # Fpga Signal S1D13504 Signal SmXYBS# GND Channel A6 Pin # Fpga Signal S1D13504 Signal SmZ Board Dimensions Bus Interface TimingMemory Address CS#, M/R# Decode Makefpga file Parts List Item # Qty Reference Part Description Schematic S5U13504-D9000 Schematic Diagram 2 S5U13504-D9000 Schematic Diagram 3 D9000 PCB Layout Component Placement Component Placement Perspective View S5U13504-D9000 Perspective View Power Consumption Document Number X19A-G-006-04 S1D13504 Power Consumption X19A-G-006-04 S1D13504 Power Consumption S1D13504 Total Power Consumption SummaryConditions Interfacing to the Philips Mips PR31500/PR31700 Processor Document Number X19A-G-005-08 This page Left Blank Direct Connection to the Philips PR31500/PR31700 This page Left Blank S1D13504 to PR31500/PR31700 Connection using One IT8368E List of Tables This page Left Blank Introduction Interfacing to the PR31500/PR31700 WAIT# RESET# S1D13504 Host Bus InterfaceGeneric MPU Host Bus Interface Pin Mapping S1D13504 Generic MPU Pin Names Generic MPU Host Bus Interface Signals Direct Connection to the Philips PR31500/PR31700 Hardware Description Memory Mapping and Aliasing S1D13504 Configuration MD1 MD2MD3 MD4 System Design Using the IT8368E PC Card Buffer Hardware Description-Using One IT8368E Chip Select Logic Vancouver Design Center Hardware Description-Using Two IT8368E’s PR31500/PR31700 S1D13504 IT8368E Configuration TX3912 Address Size Function CARDnIOEN=0 CARDnIOEN=1 IT8368E Uses PC Card Slot # Philips Address Size Function S1D13504 Configuration using the IT8368E Software References DocumentsDocument Sources Technical Support Epson LCD/CRT Controllers S1D13504Philips Mips PR31500/PR31700 Processor ITE IT8368E This page Left Blank Interfacing to the NEC VR4102 Microprocessor Document Number X19A-G-007-07 X19A-G-007-07 Issue Date 01/02/02 Introduction Interfacing to the NEC VR4102 This page Left Blank NEC VR4102 Read/Write Cycles This page Left Blank Introduction Interfacing to the NEC VR4102 NEC VR4102 System BusOverview LCD Memory Access Cycles Lcdrdy S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals VR4102 to S1D13504 Interface Read/WriteDecode Logic S1D13504 Hardware Configuration Generic bus interface e.g. MPC821, ISA bus interface NEC VR4102 Configuration NEC Signals Cycle S1D13504 SignalsWR# Write Software References NEC Electronics Inc. VR4102 Japan North America Taiwan, R.O.C This page Left Blank Interfacing to the Motorola MCF5307 Coldfire Microprocessor X19A-G-011-07 Issue Date 01/02/02 S1D13504 Bus Interface This page Left Blank List of Tables This page Left Blank Introduction Interfacing to the MCF5307 MCF5307 System BusNormal Non-Burst Bus Transactions MCF5307 Memory Read Cycle Chip-Select Module Burst Cycles S1D13504 Bus Interface Generic MPU Host Bus Interface Signals MCF5307 To S1D13504 Interface Hardware Connections S1D13504 Configuration Settings MCF5307 Chip Select Configuration Memory/Register Mapping Software Motorola Inc. Motorola Literature Distribution Center, 800 Motorola MCF5307 Processor S1D13504 Color Graphics LCD / CRT Controller X19A-G-013-02 Issue Date 01/02/02 Introduction Interfacing to the MC68328 This page Left Blank Generic MPU Host Bus Interface Pin Mapping This page Left Blank Introduction Interfacing to the MC68328 68328 System Bus S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals Busclk RESET# MC68328 To S1D13504 Interface CSB3 Dtack UWE LWE CLK0 MD6 MD7 MC68328 Chip Select Configuration Option Memory Selection Software References Motorola MC68328 Processor This page Left Blank Interfacing to the Motorola MPC821 Microprocessor X19A-G-010-05 Issue Date 01/02/02 Introduction Interfacing to the MPC821 This page Left Blank List of Tables This page Left Blank Introduction Interfacing to the MPC821 MPC8xx System BusMPC821 Bus Overview Power PC Memory Read Cycle Power PC Memory Write Cycle Memory Controller Module General-Purpose Chip Select Module Gpcm User-Programmable Machine UPM S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals MPC821 to S1D13504 Interface Typical Implementation of MPC821 to S1D13504 Interface AB9 AB8AB7 AB6 Sreset SysclkCS4 WE0 S1D13504 Hardware Configuration MPC821 Chip Select Configuration Register/Memory Mapping Test Software Source Code Epson Research and Development Software References Motorola MPC821 Processor Interfacing to the PC Card Bus Document Number X19A-G-009-05 This page Left Blank Introduction Interfacing to the PC Card Bus This page Left Blank PC Card Read Cycle This page Left Blank Introduction Memory Access Cycles Interfacing to the PC Card BusPC Card System Bus PC Card Overview PC Card Read Cycle S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals PC Card to S1D13504 Interface Typical Implementation of PC Card to S1D13504 Interface SH-3 Generic MPU PAL Equations Equations Software PCMCIA/JEIDA, PC Card Standard -- March PC Card Standard Pcmcia This page Left Blank Interfacing to the Toshiba Mips TX3912 Processor Document Number X19A-G-012-04 This page Left Blank Direct Connection to the Toshiba TX3912 This page Left Blank S1D13504 to TX3912 Connection using One IT8368E This page Left Blank Introduction Interfacing to the TX3912 S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals Direct Connection to the Toshiba TX3912 Memory Mapping and Aliasing S1D13504 Hardware Configuration System Design Using the IT8368E PC Card Buffer S1D13504 to TX3912 Connection using One IT8368E Hardware Description-Using Two IT8368E’s S1D13504 to TX3912 Connection using Two IT8368E IT8368E Configuration 64Mb 64Mb Card 2 Attribute64Mb Card 1 Memory 64Mb Card 2 Memory S1D13504 Configuration Software References Toshiba Mips TX3912 Processor ITE IT8368E This page Left Blank