Manuals / Epson / Computer Equipment / Printer

Epson S1D13504 manual Program Messages, Error Too many devices registered

Models: S1D13504

1 504

Download 504 pages 7.58 Kb

Page 236

Page 4	Epson Research and Development
	Vancouver Design Center

Usage

PC platform: at the prompt, type 13504show [b=??] [/a] [/lcd] [/crt] [/vertical] [/?].

Embedded platform: execute 13504show and at the prompt, type the command line argument.

Where:	b=??	starts 13504SHOW at a user specified bits-per-pixel (bpp)
		level, where ?? can be: 1, 2, 4, 8, 15, or 16
	/a	automatically cycles through all video modes
	/lcd	displays on the LCD panel
	/crt	displays on the CRT
	/vertical	displays vertical line pattern
	/?	displays the help screen
	/noinit	bypasses register initialization

Comments

•13504SHOW cannot show a greater color depth than the display allows.

•The PC must not have more than 12M bytes of system memory when used with the S5U13504B00C board.

•Follow simultaneous display guidelines for correct simultaneous display operation.

•To determine if the CRT will operate correctly when using a dual panel, refer to the “Maximum Frame Rates” table in the S1D13504 “Functional Hardware Specification,” document number X19A-A-002-xx.

•When editing in 13504CFG with CRT enabled and panel disabled, select “Single Panel” from the “Edit Panel Setup” submenu.

•When a CRT is enabled, the CRT settings will override the panel settings. If a panel is also used, the CRT timing values will have to be changed to more closely match the panel's timing.

•A CRT cannot show 15 or 16 bits-per-pixel.

•Do not attach a panel with a 16-bit interface to the S1D13504 when a CRT is also attached.

Program Messages

ERROR: Too many devices registered.

There are too many display devices attached to the HAL. The HAL can only manage 10 devices simultaneously.

ERROR: Could not register S1D13504 device.

A 13504 device was not found at the configured addresses. Check the configuration address using the 13504CFG configuration program.

ERROR: Did not detect S1D13504.

The HAL was unable to read the revision code register on the S1D13504. Ensure that the S1D13504 hardware is installed and that the hardware platform has been set up correctly.

S1D13504	13504SHOW Demonstration Program
X19A-B-002-05	Issue Date: 01/01/30

Image 236

Epson S1D13504 manual Program Messages, Error Too many devices registered

Contents

Technical Manual Document Number X19A-Q-002-14This page Left Blank Customer Support Information This page Left Blank Power Down Modes General Purpose IO pinsMemory Interface CPU InterfaceCPU RamdacHardware Functional Specification Document Number X19A-A-002-18X19A-A-002-18 Issue Date 01/01/30 Table of Contents Registers Display Configuration 116 Power Save Modes 128Display Buffer Clocking 119This page Left Blank List of Tables Vancouver Design Center List of Figures Vancouver Design Center Overview Description IntroductionScope Features Memory InterfaceCPU Interface Display SupportDisplay Modes Clock SourceMiscellaneous Package and PinTypical System Implementation Diagrams LCDManagement MC68000 Typical System Diagram Generic Bus, 1Mx16 FPM/EDO-DRAM Functional Block Diagram Block DescriptionFunctional Block Descriptions Host Interface Memory ControllerLCD Interface Power SaveLook-Up Table Package type 128 pin surface mount QFP15 Pinout Diagram for S1D13504F00APin Out Pinout Diagram for S1D13504F01A Package type 128 pin surface mount TQFP15Pinout Diagram for S1D13504F02A Package type 144 pin surface mount QFP20Pin Description KeyAB0 TS2CS# BusclkBS# RD/WR#RESET# WAIT# TS2LCAS# CO1 UCAS# CO1WE# CO1 RAS# CO1MA9 TS1 Clock Input LCD Interface Pin DescriptionsCRT and External Ramdac Interface CRT and Ramdac Interface Pin Descriptions HrtcVrtc BLANK# CN3Power Supply Pin # Pin Name Type Driver Description F00A F02A F01ASummary of Configuration Options Multiple Function Pin Mapping S1D13504 SH-3 MC68K Bus Generic MPU Pin NamesAsym 256Kx16 Asym 1Mx1611 LCD, CRT, Ramdac Interface Pin Mapping Symbol Parameter Condition Min Typ Max Units C. CharacteristicsSymbol Parameter Rating Units Low Level Output Voltage Output Leakage CurrentOutput Pin Capacitance Bidirectional Pin CapacitanceWAIT# CPU Interface Timing 1 SH-3 Interface TimingRD/WR# BS# Symbol Parameter Min Max Units T13 T14 T15 D150read 2 MC68K Bus 1 Interface Timing e.g. MC68000AS# UDS# LDS# AS# high setup to CLK AS# high to DTACK# high impedanceD150 hold from falling edge of DTACK# write cycle D150 valid to DTACK# falling edge read cycle3 MC68K Bus 2 Interface Timing e.g. MC68030 A200 SIZ10 M/R#AS# DS# T13 T14 T15D3116 hold from falling edge of DSACK1# write cycle D3116 valid to DSACK1# falling edge read cycleGeneric MPU Interface Synchronous Timing BclkA200 RD0#,RD1# WE0#,WE1# Hi-ZLow write cycle D150 hold from WE0#, WE1# high write cycle Hi-Z Valid T10 D150read Generic MPU Interface Asynchronous TimingA200 Valid T82 Symbol Parameter Min Typ Max Units Clock Input RequirementsMemory Interface Timing EDO-DRAM Read Timing RAS# CAS#EDO Dram Read Timing EDO-DRAM Write Timing RAS# CAS# WE#T14 Write Data setup time 45 t1 T15 Write Data hold time 55 t1 + CAS# precharge time 45 t1EDO-DRAM Read-Write Timing EDO-DRAM Read-Write TimingEDO Dram Read-Write Timing EDO-DRAM CAS Before RAS Refresh Timing 10 EDO-DRAM CAS Before RAS Refresh TimingEDO-DRAM Self-Refresh Timing 11 EDO-DRAM Self-Refresh TimingFPM-DRAM Read Timing 12 FPM-DRAM Read Timing12 FPM Dram Read Timing FPM-DRAM Write Timing 13 FPM-DRAM Write TimingT14 Write Data setup time 45 t1 T15 Write Data hold time FPM-DRAM Read-Write Timing 14 FPM-DRAM Read-Write Timing45 t1 S1D13504 FPM-DRAM CAS# Before RAS# Refresh Timing RAS# precharge time REG22h bits 32 = 01 or 45 t1FPM-DRAM Self-Refresh Timing 16 FPM-DRAM CBR Self-Refresh TimingDisplay Interface Power-On/Reset Timing Fpframe activeSuspend Timing MclkSingle Monochrome 4-Bit Panel Timing VDP =Vndp = HDP =Sync Timing Data TimingSingle Monochrome 8-Bit Panel Timing VDPVndp HDPUD30, LD30 setup to Fpshift falling edge UD30, LD30 hold to Fpshift falling edge= REG05h bits 40 + 1*8 23 Ts = REG05h bits 40 + 1*8 14 TsSingle Color 4-Bit Panel Timing 23 Single Color 4-Bit Panel Timing= REG05h bits 40 + 1*8 17 Ts = REG04h bits 60+1*8 1 Ts= REG05h bits 40 + 1*8 26 Ts Single Color 8-Bit Panel Timing Format 25 Single Color 8-Bit Panel Timing FormatUD30, LD30 setup to FPSHIFT2 rising, Fpshift falling edge Fpline pulse width Fpline periodFPSHIFT2 falling edge to Fpline rising edge FPSHIFT2, Fpshift pulse width high27 Single Color 8-Bit Panel Timing Format T1min = t3min 9Ts Single Color 16-Bit Panel Timing VDP Vndp LINE1 LINE2 LINE3 LINE4 LINE479 LINE480 HDP HndpUD70, LD70 setup to Fpshift falling edge UD70, LD70 hold to Fpshift falling edgeDual Monochrome 8-Bit Panel Timing Fpshift UD3 UD2 UD1 UD0 LD3 LD2 LD1 LD0= REG05h bits 40 + 1*8 8 Ts Dual Color 8-Bit Panel Timing 33 Dual Color 8-Bit Panel Timing= REG05h bits 40 + 1*8 9 Ts Dual Color 16-Bit Panel Timing 35 Dual Color 16-Bit Panel TimingUD70 LD70 12 16-Bit TFT Panel Timing = Vertical Display Period = REG09h bits 10, REG08h bits 70 +38 TFT A.C. Timing = REG0Ch bits 20+1 lines = REG04h bits 60+1*8 + REG05h bits 40+1*8 Ts= REG07h bits 30+1*8 Ts CRT Timing 39 CRT Timing40 CRT A.C. Timing Dacclk period External Ramdac Read / Write Timing ReadWrite DACWR# pulse width lowRegisters Register MappingRegister Descriptions Revision Code RegisterTime/256 Cycles Memory Configuration RegistersMemory Configuration Register Panel/Monitor Configuration Registers Panel Type RegisterMOD Rate Register REG03h MOD Rate BitHRTC/FPLINE Start Position Register Horizontal Display Width RegisterHorizontal Non-Display Period Register Hrtc Fpline HRTC/FPLINE Pulse Width RegisterVertical Display Height Register Vrtc Fpframe Vertical Non-Display Period RegisterVRTC/FPFRAME Start Position Register VRTC/FPFRAME Pulse Width Register REG0ChFpframe Vrtc Vrtc PolarityDisplay Configuration Registers Display Mode RegisterSimultaneous Display Option Select Bits Even Scan OnlyNumber of Bits-Per-Pixel Selection Screen 1 Line Compare Register Screen 1 Display Start Address RegisterMemory Address Offset Register Screen 2 Display Start Address Register 0 RWScreen 2 Display Start Address Register Clock Configuration Register Clock Configuration RegisterPixel Panning Register Number of Bits-Per-Pixel Screen 2 Pixel Panning Bits UsedPower Save Configuration Registers Power Save Configuration RegisterMiscellaneous Disable Register Miscellaneous RegistersMD Configuration Readback Register Gpio Configuration RegisterREG1Dh MD15 MD14 MD13 MD12 MD11 MD10 MD9 MD8Vancouver Design Center REG1Fh GPIO11 Pin GPIO10 Pin GPIO9 Pin GPIO8 Pin IO Config Gpio Status / Control Register Gpio Status / Control Register REG21hGPO GPIO11 Pin GPIO10 Pin GPIO9 Pin GPIO8 Pin Control IO StatusPerformance Enhancement Register REG22h EDO Read RC Timing RAS# toREG22h Bits Minimum Random Cycle Width t RCRAS# to CAS# Delay tRCD Optimal Dram TimingREG22h Bit RAS# Precharge Width t RPLook-Up Table Address Register RGB Index Bits Look-Up Table Access Pointer SequenceLook-Up Table Registers Look-Up Table Data Register Look-Up Table Bank Select RegisterREG26h LUT Data Bit REG27h Red Bank Blue Bank Green Bank Select BitRamdac Read Mode Address Register Ramdac Write Mode Address RegisterExternal Ramdac Control Registers Ramdac Pixel Read Mask RegisterRamdac Palette Data Register REG2Eh or REG2FhDisplay Buffer 512K byte Memory AB200Image Buffer Half Frame BufferDisplay Configuration Display Mode Data Format15/16 Bit-Per-Pixel Format Memory Organization Image Buffer Image ManipulationDisplay Clocking Maximum Mclk Pclk RatiosDisplay type Maximum Pclk Allowed Bpp 16 bppFrame Rate Calculation = PclkSpeed Grade Bpp Clock Hndpt s Panel MHzFPM-DRAM Bit-Per-Pixel Mode Display Mode Bit Wide Look-Up TableLook-Up Table Architecture Gray Shade Display ModesBit-Per-Pixel Mode Bit-Per-Pixel Color Mode Color Display ModesBank Selected Bank Entry Bit Red data output Logic Red Look-Up Table 0000 0001 0010 0011 0100 0101 Entry 0110 Color Data Format Red Look-Up Table Software Suspend Power Save ModesHardware Suspend Power Save Mode Function Summary Pin States in Power Save ModesPower Save Mode PSM Pin State Pins Normal Software Hardware Active SuspendQFP15 128 pin Unit mm Mechanical Data14.1 QFP15-128 S1D13504F00A ±0.2 TQFP15-128 S1D13504F01ATQFP15 128 pin Unit mm 125 QFP20-144 S1D13504F02AQFP20 144 pin Unit mm Programming Notes and Examples Document Number X19A-G-002-07This page Left Blank Advanced Techniques LCD Power Sequencing and Power Save ModesIntroduction Programming the S1D13504 Registers CRT Considerations Identifying the S1D13504 Hardware Abstraction Layer HALSample Code Appendix a Supported Panel ValuesInitializing the S1D13504 Registers This page Left Blank Introduction 3 REG02 bit 1 Dual/Single Panel Type Programming the S1D13504 Registers2 REG22 bits 7-2 Performance Enhancement Register Register Initialization Initialization Sequence 4 REG1B bit 0 Half Frame Buffer Disable5 REG23 Display Fifo Operation Description Initialization ExampleInitializing the S1D13504 Registers Re-Programming Registers Disabling the Half Frame Buffer SequencePixel Bit Display Buffer LocationBit Memory Organization for Eight Bit-per-pixel 256 Colors Bit Red Bit Green Bit Blue BitBit Reserved Red Bit Green Bit Blue Bit Memory Organization for 15 Bit-per-pixel 32768 ColorsMemory Organization for 16 Bit-per-pixel 65536 Colors Look-Up Table LUT REG24h Look-Up Table Address Register Read/WriteREG26h Look-Up Table Data Register Read/Write REG27h Look-Up Table Bank Register Read/WriteBank Select Bits Bank Look-Up Table ConfigurationsLook-Up Table Organization Recommended LUT Values for 1 bpp Color Mode Recommended LUT Values for 2 bpp Color ModeColor Modes Address Red Green Blue11 Recommended LUT Values For 8 bpp Color Mode 12 Examples of 256 Pixel Colors Using Linear LUT Gray Shade Modes13 Recommended LUT Values for 1 bpp Gray Shades Pixel Value ColorLUT Address Green LUT Data 14 Recommended LUT Values for 2 bpp Gray Shades15 Recommended LUT Values for 8 bpp Gray Shade Bpp Gray Shade Advanced Technique s Virtual DisplayRegisters ExamplesREG16h Memory Address Offset Register REG17h Memory Address Offset RegisterPanning and Scrolling Number of Pixels Panned Using Start Address Active Pixel Pan BitsExample 4 Panning Right and Left Split Screen REG0E Screen 1 Line Compare RegisterLine Compare Bit REG0F Screen 1 Line Compare RegisterREG15h Screen 2 Display Start Address Register REG13h Screen 2 Display Start Address RegisterREG14h Screen 2 Display Start Address Register LCD Power Sequencing and Power Save Modes Introduction to LCD Power SequencingIntroduction to Power Save Modes Display Mode RegisterSuspend Enable Sequence Shortening the 128 Frame delay using Software SuspendShortening the 128 Frame Delay using Hardware SUSPEND# Suspend SequencingSuspend Disable Sequence LCD Enable/Disable Sequencing Reg0D bitLCD Enable / Disable using Power Save Modes LCD Enable / Disable using Manual ControlCRT Considerations IntroductionCRT Only Ramdac Register Mapping for Little/Big-EndianSimultaneous Display Related Register Data for CRT OnlyAddress Address Related register data for Simultaneous Display Register 640X480@75Hz 640X480@60HzIdentifying the S1D13504 Initialization Int seDeRegisterDeviceint device Hardware Abstraction Layer HALAPI for 13504HAL Int seGetIdint device, Byte *pId Int seInitHalvoidInt seValidStdDeviceint device Int seSetInitint deviceInt seValidRegisteredDeviceint device Int seGetBitsPerPixelint device, Byte *pBitsPerPixel Int seGetBytesPerScanlineint device, int *pBytesInt seGetLastUsableByteint device, Dword *pLastByte Int seGetLinearDispAddrint device, Dword *pDispLogicalAddrInt seReadDisplayWordint device, Dword offset, Word *pWord Int seGetScreenSizeint device, int *width, int *heightInt seReadDisplayByteint device, Dword offset, Byte *pByte Int seSetBitsPerPixelint device, Byte BitsPerPixel Int seSplitInitint device, Dword Scrn1Addr, Dword Scrn2AddrInt seVirtInitint device, int xVirt, long *yVirt Int seVirtMoveint device, Byte WhichScreen, int x, int yVancouver Design Center Int seGetLutint device, Byte *pLut Color Manipulation Int seGetDacint device, Byte *pDacInt seGetDacEntryint device, Byte index, Byte *pEntry Int seSetDacEntryint device, Byte index, Byte *pEntry Int seGetLutEntryint device, Byte index, Byte *pEntryInt seSetDacint device, Byte *pDac Int seSetLutint device, Byte *pLut Int seSetLutEntryint device, Byte index, Byte *pEntryInt seDrawTextint device, char *fmt Int sePutcint device, int ch Int seGetcharvoidInt sePutcharint ch Int seSetRegint device, int index, Byte val Miscellaneous Int seDelayint device, Dword SecondsInt seSetPixelint device, int x, int y, Dword color Word seRotateByteLeftBYTE val, Byte bits Word seRotateByteRightBYTE val, Byte bitsSample code using 13504HAL API Sample CodeSample code without using 13504HAL API Vancouver Design Center Pclk To arrive at the frame rate closest to the desired Words Fifo Appendix a Supported Panel Values Supported Panel ValuesPassive Single Panel Passive Dual PanelTFT Panel TFT 16-Bit Register Single01/02/02 Number of Bits/Pixel 13504CFG.EXE Configuration Program Document Number X19A-B-001-04Vancouver Design Center X19A-B-001-04 Script Mode Interactive Mode 13504CFG.EXE Program RequirementsThis page Left Blank 13504CFG View Menu This page Left Blank 13504CFG.EXE Usage InstallationProgram Requirements Script Mode Interactive Mode 13504CFG Menu BarMaking 13504CFG Menu Selections Files Menu View Menu 13504CFG Current Configuration Device Menu Panel Edit Panel Setup CRT Edit CRT Setup Advanced Memory Edit Advanced Memory Setup Power Management Edit Power Setup Lookup Table LUT Edit LUT Setup Setup Help Menu Comments Sample Program MessagesThis page Left Blank 13504SHOW Demonstration Program Document Number X19A-B-002-05This page Left Blank 13504SHOW S1D13504 Supported Evaluation PlatformsError Too many devices registered Program Messages13504SPLT Display Utility Document Number X19A-B-003-05This page Left Blank 13504SPLT 13504SPLT Example Comments This page Left Blank 13504VIRT Display Utility Document Number X19A-B-004-05S1D13504 13504VIRT Display Utility X19A-B-004-05 13504VIRT 13504VIRT Example Comments This page Left Blank 13504PLAY Diagnostic Utility Document Number X19A-B-005-05This page Left Blank 13504PLAY Reads/writes the registers 13504PLAY Example ScriptingComments 13504BMP Demonstration Program Document Number X19A-B-006-04This page Left Blank 13504BMP Program Messages 13504PWR Software Suspend Power Sequencing Utility Document Number X19A-B-007-04X19A-B-007-04 Issue Date 01/02/01 13504PWR Selects software suspend Error Unknown command line argument This page Left Blank 13504DCFG Configuration Program Document Number X19A-B-008-02This page Left Blank Table of Contents This page Left Blank List of Figures Clocks Tab Panel TabThis page Left Blank Usage Installation13504DCFG 13504DCFG Configuration Tabs General Tab General TabMemory Tab Memory TabClocks Tab Clocks TabClocks Tab ClkiLCD Mclkpclk CRT MclkpclkPanel Tab Panel TabPanel Tab STN/TFTHRTC/FPLINE VRTC/FPFRAMECRT Tab CRT TabDefaults Tab Defaults TabSelect the default display device. Three display modes LCD Initializes the registers based on the default modeRegisters Tab Registers TabMiscellaneous Flags Tab Miscellaneous Flags TabSaving to a File Resolution Frame Rate Hz Pclk MHz Supported Dram Types CommentsWindows CE Display Drivers Document Number X19A-E-001-04X19A-E-001-04 DIP Switch Program RequirementsExample Driver Builds Windows VersionWith this line Build For Cepc If CEPCDDIVGA2BPP Epson Research and Development Installation for Cepc Environment Example InstallationInstallation for Hitachi D9000 and Etma ODO Comments This page Left Blank Wind River WindML v2.0 Display Drivers Document Number X19A-E-002-03X19A-E-002-03 Issue Date 01/04/06 Wind River WindML v2.0 Display Drivers Building a WindML v2.0 Display Driver Make CPU=PENTIUM uglEpson Research and Development This page Left Blank Wind River UGL v1.2 Display Drivers Document Number X19A-E-003-02X19A-E-003-02 Wind River UGL v1.2 Display Drivers Building a UGL v1.2 Display Driver Epson Research and Development This page Left Blank Document Number X19A-G-004-06 S1D13504 X19A-G-004-06 Issue Date 01/02/02 Installation and Configuration Parts List Schematic DiagramsThis page Left Blank S1D13504B00C Schematic Diagram 1 of 6 This page Left Blank Features Installation and Configuration Configuration DIP Switch SettingsJumper Settings Host Bus SelectionLCD Signal Connector J6 LCD / Ramdac Interface Pin MappingConnector Comments Pin No CPU / BUS Interface Connector PinoutsCPU/BUS Connector H1 Pinout CPU/BUS Connector H2 Pinout Host Bus Interface Pin Mapping DB150 D150 D3116 WE1#Technical Description ISA Bus SupportNon-ISA Bus Support Dram SupportDecode Logic Clock Input SupportMonochrome LCD Panel Support Color Passive LCD Panel SupportColor TFT LCD Panel Support External Cmos Ramdac SupportPower Save Modes Core VDD Power SupplyIO VDD Power Supply Adjustable LCD Panel Negative Power SupplySchematic Notes 15 CPU/Bus Interface Header StripsParts List Item # Qty/board Designation Part Value DescriptionTIBPAL22V10-15BCNT Texas Instrument PAL 24 pin DIP package/socketedSchematic DiagramsS1D13504B00C Schematic Diagram 2 Rev.1.0 S1D13504B00C Schematic Diagram 4 Diagram 5 S1D13504B00C Schematic Diagram 6 This page Left Blank S5U13504-D9000 Document Number X19A-G-003-05S5U13504-D9000 X19A-G-003-05 Issue Date 01/02/02 Introduction Features D9000 SpecificsThis page Left Blank S5U13504-D9000 Perspective View This page Left Blank Reference S1D13504 Color Graphics LCD Controller Display BufferLCD Display Support LCD Connector Pinout LCD Interface Pin MappingAdjustable LCD Bias Power Supply CRT SupportInterface Signals Connector Pinout for Channel A6 and A7Interface Signals D9000 SpecificsDC12V Connector Pinout for Channel A7GND Channel A7 Pin # Fpga Signal S1D13504 Signal SmZ BS# GND Connectors Pinout for Channel A6Channel A6 Pin # Fpga Signal S1D13504 Signal SmXY Channel A6 Pin # Fpga Signal S1D13504 Signal SmZ Board Dimensions Bus Interface TimingMemory Address CS#, M/R# Decode Makefpga fileParts List Item # Qty Reference Part DescriptionSchematic S5U13504-D9000 Schematic Diagram 2 S5U13504-D9000 Schematic Diagram 3 D9000 PCB Layout Component Placement Component PlacementPerspective View S5U13504-D9000 Perspective ViewPower Consumption Document Number X19A-G-006-04S1D13504 Power Consumption X19A-G-006-04 S1D13504 Power Consumption Conditions S1D13504 Total Power ConsumptionSummary Interfacing to the Philips Mips PR31500/PR31700 Processor Document Number X19A-G-005-08This page Left Blank Direct Connection to the Philips PR31500/PR31700 This page Left Blank S1D13504 to PR31500/PR31700 Connection using One IT8368E List of TablesThis page Left Blank Introduction Interfacing to the PR31500/PR31700 WAIT# RESET# S1D13504 Host Bus InterfaceGeneric MPU Host Bus Interface Pin Mapping S1D13504 Generic MPU Pin NamesGeneric MPU Host Bus Interface Signals Direct Connection to the Philips PR31500/PR31700 Hardware DescriptionMemory Mapping and Aliasing MD3 MD4 S1D13504 ConfigurationMD1 MD2 System Design Using the IT8368E PC Card Buffer Hardware Description-Using One IT8368EChip Select LogicVancouver Design Center Hardware Description-Using Two IT8368E’s PR31500/PR31700 S1D13504IT8368E Configuration TX3912 Address Size Function CARDnIOEN=0 CARDnIOEN=1 IT8368E Uses PC Card Slot # Philips Address Size FunctionS1D13504 Configuration using the IT8368E Software Document Sources ReferencesDocuments Technical Support Epson LCD/CRT Controllers S1D13504Philips Mips PR31500/PR31700 Processor ITE IT8368EThis page Left Blank Interfacing to the NEC VR4102 Microprocessor Document Number X19A-G-007-07X19A-G-007-07 Issue Date 01/02/02 Introduction Interfacing to the NEC VR4102 This page Left Blank NEC VR4102 Read/Write Cycles This page Left Blank Introduction Overview Interfacing to the NEC VR4102NEC VR4102 System Bus LCD Memory Access Cycles LcdrdyS1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals Decode Logic VR4102 to S1D13504 InterfaceRead/Write S1D13504 Hardware Configuration Generic bus interface e.g. MPC821, ISA bus interfaceNEC VR4102 Configuration NEC Signals Cycle S1D13504 SignalsWR# WriteSoftware References NEC Electronics Inc. VR4102 Japan North America Taiwan, R.O.CThis page Left Blank Interfacing to the Motorola MCF5307 Coldfire Microprocessor X19A-G-011-07 Issue Date 01/02/02 S1D13504 Bus Interface This page Left Blank List of Tables This page Left Blank Introduction Normal Non-Burst Bus Transactions Interfacing to the MCF5307MCF5307 System Bus MCF5307 Memory Read Cycle Chip-Select Module Burst CyclesS1D13504 Bus Interface Generic MPU Host Bus Interface Signals MCF5307 To S1D13504 Interface Hardware ConnectionsS1D13504 Configuration Settings MCF5307 Chip Select Configuration Memory/Register MappingSoftware Motorola Inc. Motorola Literature Distribution Center, 800 Motorola MCF5307 Processor S1D13504 Color Graphics LCD / CRT Controller X19A-G-013-02 Issue Date 01/02/02 Introduction Interfacing to the MC68328 This page Left Blank Generic MPU Host Bus Interface Pin Mapping This page Left Blank Introduction Interfacing to the MC68328 68328 System BusS1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals Busclk RESET# MC68328 To S1D13504 InterfaceCSB3 Dtack UWE LWE CLK0 MD6 MD7MC68328 Chip Select Configuration Option Memory SelectionSoftware References Motorola MC68328 Processor This page Left Blank Interfacing to the Motorola MPC821 Microprocessor X19A-G-010-05 Issue Date 01/02/02 Introduction Interfacing to the MPC821 This page Left Blank List of Tables This page Left Blank Introduction MPC821 Bus Overview Interfacing to the MPC821MPC8xx System Bus Power PC Memory Read Cycle Power PC Memory Write Cycle Memory Controller Module General-Purpose Chip Select Module GpcmUser-Programmable Machine UPM S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals MPC821 to S1D13504 Interface Typical Implementation of MPC821 to S1D13504 InterfaceAB9 AB8AB7 AB6Sreset SysclkCS4 WE0S1D13504 Hardware Configuration MPC821 Chip Select Configuration Register/Memory MappingTest Software Source CodeEpson Research and Development Software References Motorola MPC821 Processor Interfacing to the PC Card Bus Document Number X19A-G-009-05This page Left Blank Introduction Interfacing to the PC Card Bus This page Left Blank PC Card Read Cycle This page Left Blank Introduction Memory Access Cycles Interfacing to the PC Card BusPC Card System Bus PC Card OverviewPC Card Read Cycle S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals PC Card to S1D13504 Interface Typical Implementation of PC Card to S1D13504 InterfaceSH-3 Generic MPUPAL Equations EquationsSoftware PCMCIA/JEIDA, PC Card Standard -- March PC Card Standard PcmciaThis page Left Blank Interfacing to the Toshiba Mips TX3912 Processor Document Number X19A-G-012-04This page Left Blank Direct Connection to the Toshiba TX3912 This page Left Blank S1D13504 to TX3912 Connection using One IT8368E This page Left Blank Introduction Interfacing to the TX3912 S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals Direct Connection to the Toshiba TX3912 Memory Mapping and Aliasing S1D13504 Hardware Configuration System Design Using the IT8368E PC Card Buffer S1D13504 to TX3912 Connection using One IT8368E Hardware Description-Using Two IT8368E’s S1D13504 to TX3912 Connection using Two IT8368E IT8368E Configuration 64Mb 64Mb Card 2 Attribute64Mb Card 1 Memory 64Mb Card 2 MemoryS1D13504 Configuration Software References Toshiba Mips TX3912 Processor ITE IT8368E This page Left Blank