MPC821 to S1D13504 Interface | Epson specs

Epson Research and Development	Page 15
Vancouver Design Center

4 MPC821 to S1D13504 Interface

4.1 Hardware Description

The interface between the S1D13504 and the MPC821 requires no glue logic. All lines are directly connected. A single resistor is used to speed up the rise time of the WAIT# (TA) signal when terminating the bus cycle.

BS# (bus start) is not used in this implementation and should be tied low (connected to GND).

The following diagram shows a typical implementation of the MPC821 to S1D13504 interface.

MPC821

A10

A[11:31]

D[0:15]

CS4

TA

WE0

WE1

OE

SYSCLK

Vcc

470

System RESET

S1D13504

M/R#

AB[20:0]

DB[15:0]

CS#

WAIT#

WE1#

WE0#

RD1#

RD0#

BUSCLK

RESET#

Note:

When connecting the S1D13504 RESET# pin, the system designer should be aware of all conditions that may reset the S1D13504 (e.g. CPU reset can be asserted during wake-up from power-down modes, or during debug states).

Figure 4-1: Typical Implementation of MPC821 to S1D13504 Interface

Note

For pin mapping see Table 3-1:, “Generic MPU Host Bus Interface Pin Mapping” .

Interfacing to the Motorola MPC821 Microprocessor	S1D13504
Issue Date: 01/02/02	X19A-G-010-05

Image 453

Epson manual Typical Implementation of MPC821 to S1D13504 Interface

Contents

Document Number X19A-Q-002-14 Technical Manual This page Left Blank Customer Support Information This page Left Blank General Purpose IO pins Power Down ModesMemory Interface CPU Interface Ramdac CPU Document Number X19A-A-002-18 Hardware Functional Specification X19A-A-002-18 Issue Date 01/01/30 Table of Contents Registers Power Save Modes 128 Display Configuration 116Display Buffer Clocking 119 This page Left Blank List of Tables Vancouver Design Center List of Figures Vancouver Design Center Introduction ScopeOverview Description Memory Interface FeaturesCPU Interface Display Support Clock Source Display ModesMiscellaneous Package and Pin LCD Typical System Implementation Diagrams Management MC68000 Typical System Diagram Generic Bus, 1Mx16 FPM/EDO-DRAM Block Description Functional Block DiagramFunctional Block Descriptions Host Interface Memory Controller Power Save Look-Up TableLCD Interface Pinout Diagram for S1D13504F00A Pin OutPackage type 128 pin surface mount QFP15 Package type 128 pin surface mount TQFP15 Pinout Diagram for S1D13504F01A Package type 144 pin surface mount QFP20 Pinout Diagram for S1D13504F02A Key Pin DescriptionAB0 TS2 Busclk CS#BS# RD/WR# WAIT# TS2 RESET# UCAS# CO1 LCAS# CO1WE# CO1 RAS# CO1 MA9 TS1 LCD Interface Pin Descriptions Clock Input CRT and External Ramdac Interface Hrtc CRT and Ramdac Interface Pin DescriptionsVrtc BLANK# CN3 Pin # Pin Name Type Driver Description F00A F02A F01A Power Supply Summary of Configuration Options S1D13504 SH-3 MC68K Bus Generic MPU Pin Names Multiple Function Pin MappingAsym 256Kx16 Asym 1Mx16 11 LCD, CRT, Ramdac Interface Pin Mapping C. Characteristics Symbol Parameter Rating UnitsSymbol Parameter Condition Min Typ Max Units Output Leakage Current Low Level Output VoltageOutput Pin Capacitance Bidirectional Pin Capacitance CPU Interface Timing 1 SH-3 Interface Timing RD/WR# BS#WAIT# Symbol Parameter Min Max Units 2 MC68K Bus 1 Interface Timing e.g. MC68000 AS# UDS# LDS#T13 T14 T15 D150read AS# high to DTACK# high impedance AS# high setup to CLKD150 hold from falling edge of DTACK# write cycle D150 valid to DTACK# falling edge read cycle A200 SIZ10 M/R# 3 MC68K Bus 2 Interface Timing e.g. MC68030AS# DS# T13 T14 T15 D3116 valid to DSACK1# falling edge read cycle D3116 hold from falling edge of DSACK1# write cycle Bclk Generic MPU Interface Synchronous TimingA200 RD0#,RD1# WE0#,WE1# Hi-Z Low write cycle D150 hold from WE0#, WE1# high write cycle Generic MPU Interface Asynchronous Timing A200 ValidHi-Z Valid T10 D150read T82 Clock Input Requirements Symbol Parameter Min Typ Max Units RAS# CAS# Memory Interface Timing EDO-DRAM Read Timing EDO Dram Read Timing RAS# CAS# WE# EDO-DRAM Write Timing 55 t1 + CAS# precharge time 45 t1 T14 Write Data setup time 45 t1 T15 Write Data hold time EDO-DRAM Read-Write Timing EDO-DRAM Read-Write Timing EDO Dram Read-Write Timing 10 EDO-DRAM CAS Before RAS Refresh Timing EDO-DRAM CAS Before RAS Refresh Timing 11 EDO-DRAM Self-Refresh Timing EDO-DRAM Self-Refresh Timing 12 FPM-DRAM Read Timing FPM-DRAM Read Timing 12 FPM Dram Read Timing 13 FPM-DRAM Write Timing FPM-DRAM Write Timing T14 Write Data setup time 45 t1 T15 Write Data hold time 14 FPM-DRAM Read-Write Timing FPM-DRAM Read-Write Timing 45 t1 S1D13504 RAS# precharge time REG22h bits 32 = 01 or 45 t1 FPM-DRAM CAS# Before RAS# Refresh Timing 16 FPM-DRAM CBR Self-Refresh Timing FPM-DRAM Self-Refresh Timing Fpframe active Display Interface Power-On/Reset Timing Mclk Suspend Timing VDP = Single Monochrome 4-Bit Panel TimingVndp = HDP = Data Timing Sync Timing VDP Single Monochrome 8-Bit Panel TimingVndp HDP UD30, LD30 hold to Fpshift falling edge UD30, LD30 setup to Fpshift falling edge= REG05h bits 40 + 1*8 23 Ts = REG05h bits 40 + 1*8 14 Ts 23 Single Color 4-Bit Panel Timing Single Color 4-Bit Panel Timing = REG04h bits 60+1*8 1 Ts = REG05h bits 40 + 1*8 26 Ts= REG05h bits 40 + 1*8 17 Ts 25 Single Color 8-Bit Panel Timing Format Single Color 8-Bit Panel Timing Format Fpline pulse width Fpline period UD30, LD30 setup to FPSHIFT2 rising, Fpshift falling edgeFPSHIFT2 falling edge to Fpline rising edge FPSHIFT2, Fpshift pulse width high 27 Single Color 8-Bit Panel Timing Format T1min = t3min 9Ts VDP Vndp LINE1 LINE2 LINE3 LINE4 LINE479 LINE480 HDP Hndp Single Color 16-Bit Panel Timing UD70, LD70 hold to Fpshift falling edge UD70, LD70 setup to Fpshift falling edge Fpshift UD3 UD2 UD1 UD0 LD3 LD2 LD1 LD0 Dual Monochrome 8-Bit Panel Timing = REG05h bits 40 + 1*8 8 Ts 33 Dual Color 8-Bit Panel Timing Dual Color 8-Bit Panel Timing = REG05h bits 40 + 1*8 9 Ts 35 Dual Color 16-Bit Panel Timing Dual Color 16-Bit Panel Timing UD70 LD70 = Vertical Display Period = REG09h bits 10, REG08h bits 70 + 12 16-Bit TFT Panel Timing 38 TFT A.C. Timing = REG04h bits 60+1*8 + REG05h bits 40+1*8 Ts = REG07h bits 30+1*8 Ts= REG0Ch bits 20+1 lines 39 CRT Timing CRT Timing 40 CRT A.C. Timing Dacclk period Read External Ramdac Read / Write TimingWrite DACWR# pulse width low Register Mapping RegistersRegister Descriptions Revision Code Register Memory Configuration Registers Memory Configuration RegisterTime/256 Cycles Panel Type Register Panel/Monitor Configuration RegistersMOD Rate Register REG03h MOD Rate Bit Horizontal Display Width Register Horizontal Non-Display Period RegisterHRTC/FPLINE Start Position Register HRTC/FPLINE Pulse Width Register Vertical Display Height RegisterHrtc Fpline Vertical Non-Display Period Register VRTC/FPFRAME Start Position RegisterVrtc Fpframe REG0Ch VRTC/FPFRAME Pulse Width RegisterFpframe Vrtc Vrtc Polarity Display Mode Register Display Configuration RegistersSimultaneous Display Option Select Bits Even Scan Only Number of Bits-Per-Pixel Selection Screen 1 Display Start Address Register Screen 1 Line Compare Register Screen 2 Display Start Address Register 0 RW Screen 2 Display Start Address RegisterMemory Address Offset Register Clock Configuration Register Clock Configuration RegisterPixel Panning Register Number of Bits-Per-Pixel Screen 2 Pixel Panning Bits Used Power Save Configuration Register Power Save Configuration RegistersMiscellaneous Disable Register Miscellaneous Registers Gpio Configuration Register MD Configuration Readback RegisterREG1Dh MD15 MD14 MD13 MD12 MD11 MD10 MD9 MD8 Vancouver Design Center REG1Fh GPIO11 Pin GPIO10 Pin GPIO9 Pin GPIO8 Pin IO Config Gpio Status / Control Register REG21h Gpio Status / Control RegisterGPO GPIO11 Pin GPIO10 Pin GPIO9 Pin GPIO8 Pin Control IO Status REG22h EDO Read RC Timing RAS# to Performance Enhancement RegisterREG22h Bits Minimum Random Cycle Width t RC Optimal Dram Timing RAS# to CAS# Delay tRCDREG22h Bit RAS# Precharge Width t RP RGB Index Bits Look-Up Table Access Pointer Sequence Look-Up Table RegistersLook-Up Table Address Register Look-Up Table Bank Select Register Look-Up Table Data RegisterREG26h LUT Data Bit REG27h Red Bank Blue Bank Green Bank Select Bit Ramdac Write Mode Address Register Ramdac Read Mode Address RegisterExternal Ramdac Control Registers Ramdac Pixel Read Mask Register REG2Eh or REG2Fh Ramdac Palette Data Register 512K byte Memory AB200 Display Buffer Half Frame Buffer Image Buffer Display Mode Data Format Display Configuration 15/16 Bit-Per-Pixel Format Memory Organization Image Manipulation DisplayImage Buffer Maximum Mclk Pclk Ratios ClockingDisplay type Maximum Pclk Allowed Bpp 16 bpp = Pclk Frame Rate CalculationSpeed Grade Bpp Clock Hndpt s Panel MHz FPM-DRAM Display Mode Bit Wide Look-Up Table Bit-Per-Pixel ModeLook-Up Table Architecture Gray Shade Display Modes Bit-Per-Pixel Mode Color Display Modes Bit-Per-Pixel Color Mode Bank Selected Bank Entry Bit Red data output Logic Red Look-Up Table 0000 0001 0010 0011 0100 0101 Entry 0110 Color Data Format Red Look-Up Table Power Save Modes Hardware SuspendSoftware Suspend Pin States in Power Save Modes Power Save Mode Function SummaryPower Save Mode PSM Pin State Pins Normal Software Hardware Active Suspend Mechanical Data 14.1 QFP15-128 S1D13504F00AQFP15 128 pin Unit mm TQFP15-128 S1D13504F01A TQFP15 128 pin Unit mm±0.2 QFP20-144 S1D13504F02A QFP20 144 pin Unit mm125 Document Number X19A-G-002-07 Programming Notes and Examples This page Left Blank LCD Power Sequencing and Power Save Modes Introduction Programming the S1D13504 RegistersAdvanced Techniques Identifying the S1D13504 Hardware Abstraction Layer HAL CRT ConsiderationsSample Code Appendix a Supported Panel Values Initializing the S1D13504 Registers This page Left Blank Introduction Programming the S1D13504 Registers 2 REG22 bits 7-2 Performance Enhancement Register3 REG02 bit 1 Dual/Single Panel Type 4 REG1B bit 0 Half Frame Buffer Disable 5 REG23 Display FifoRegister Initialization Initialization Sequence Initialization Example Initializing the S1D13504 RegistersOperation Description Disabling the Half Frame Buffer Sequence Re-Programming Registers Display Buffer Location BitPixel Bit Bit Red Bit Green Bit Blue Bit Memory Organization for Eight Bit-per-pixel 256 Colors Memory Organization for 15 Bit-per-pixel 32768 Colors Memory Organization for 16 Bit-per-pixel 65536 ColorsBit Reserved Red Bit Green Bit Blue Bit REG24h Look-Up Table Address Register Read/Write Look-Up Table LUTREG26h Look-Up Table Data Register Read/Write REG27h Look-Up Table Bank Register Read/Write Bank Select Bits Look-Up Table Configurations Look-Up Table OrganizationBank Recommended LUT Values for 2 bpp Color Mode Recommended LUT Values for 1 bpp Color ModeColor Modes Address Red Green Blue 11 Recommended LUT Values For 8 bpp Color Mode Gray Shade Modes 12 Examples of 256 Pixel Colors Using Linear LUT13 Recommended LUT Values for 1 bpp Gray Shades Pixel Value Color 14 Recommended LUT Values for 2 bpp Gray Shades 15 Recommended LUT Values for 8 bpp Gray ShadeLUT Address Green LUT Data Bpp Gray Shade Virtual Display Advanced Technique s Examples RegistersREG16h Memory Address Offset Register REG17h Memory Address Offset Register Panning and Scrolling Active Pixel Pan Bits Number of Pixels Panned Using Start Address Example 4 Panning Right and Left REG0E Screen 1 Line Compare Register Split ScreenLine Compare Bit REG0F Screen 1 Line Compare Register REG13h Screen 2 Display Start Address Register REG14h Screen 2 Display Start Address RegisterREG15h Screen 2 Display Start Address Register Introduction to LCD Power Sequencing LCD Power Sequencing and Power Save ModesIntroduction to Power Save Modes Display Mode Register Shortening the 128 Frame delay using Software Suspend Suspend Enable SequenceShortening the 128 Frame Delay using Hardware SUSPEND# Suspend Sequencing LCD Enable/Disable Sequencing Reg0D bit Suspend Disable SequenceLCD Enable / Disable using Power Save Modes LCD Enable / Disable using Manual Control Introduction CRT ConsiderationsCRT Only Ramdac Register Mapping for Little/Big-Endian Related Register Data for CRT Only Simultaneous Display Address Address Register 640X480@75Hz 640X480@60Hz Related register data for Simultaneous Display Identifying the S1D13504 Hardware Abstraction Layer HAL API for 13504HALInitialization Int seDeRegisterDeviceint device Int seInitHalvoid Int seGetIdint device, Byte *pId Int seSetInitint device Int seValidRegisteredDeviceint deviceInt seValidStdDeviceint device Int seGetBytesPerScanlineint device, int *pBytes Int seGetBitsPerPixelint device, Byte *pBitsPerPixelInt seGetLastUsableByteint device, Dword *pLastByte Int seGetLinearDispAddrint device, Dword *pDispLogicalAddr Int seGetScreenSizeint device, int *width, int *height Int seReadDisplayByteint device, Dword offset, Byte *pByteInt seReadDisplayWordint device, Dword offset, Word *pWord Int seSplitInitint device, Dword Scrn1Addr, Dword Scrn2Addr Int seSetBitsPerPixelint device, Byte BitsPerPixel Int seVirtMoveint device, Byte WhichScreen, int x, int y Int seVirtInitint device, int xVirt, long *yVirt Vancouver Design Center Color Manipulation Int seGetDacint device, Byte *pDac Int seGetDacEntryint device, Byte index, Byte *pEntryInt seGetLutint device, Byte *pLut Int seGetLutEntryint device, Byte index, Byte *pEntry Int seSetDacint device, Byte *pDacInt seSetDacEntryint device, Byte index, Byte *pEntry Int seSetLutEntryint device, Byte index, Byte *pEntry Int seSetLutint device, Byte *pLut Int seDrawTextint device, char *fmt Int seGetcharvoid Int sePutcharint chInt sePutcint device, int ch Miscellaneous Int seDelayint device, Dword Seconds Int seSetPixelint device, int x, int y, Dword colorInt seSetRegint device, int index, Byte val Word seRotateByteRightBYTE val, Byte bits Word seRotateByteLeftBYTE val, Byte bits Sample Code Sample code using 13504HAL API Sample code without using 13504HAL API Vancouver Design Center Pclk To arrive at the frame rate closest to the desired Words Fifo Supported Panel Values Appendix a Supported Panel ValuesPassive Single Panel Passive Dual Panel TFT 16-Bit Register Single TFT Panel 01/02/02 Number of Bits/Pixel Document Number X19A-B-001-04 13504CFG.EXE Configuration Program Vancouver Design Center X19A-B-001-04 13504CFG.EXE Program Requirements Script Mode Interactive Mode This page Left Blank 13504CFG View Menu This page Left Blank 13504CFG.EXE Installation Program RequirementsUsage Script Mode 13504CFG Menu Bar Interactive Mode Making 13504CFG Menu Selections Files Menu View Menu 13504CFG Current Configuration Device Menu Panel Edit Panel Setup CRT Edit CRT Setup Advanced Memory Edit Advanced Memory Setup Power Management Edit Power Setup Lookup Table LUT Edit LUT Setup Setup Help Menu Sample Program Messages Comments This page Left Blank Document Number X19A-B-002-05 13504SHOW Demonstration Program This page Left Blank S1D13504 Supported Evaluation Platforms 13504SHOW Program Messages Error Too many devices registered Document Number X19A-B-003-05 13504SPLT Display Utility This page Left Blank 13504SPLT 13504SPLT Example Comments This page Left Blank Document Number X19A-B-004-05 13504VIRT Display Utility S1D13504 13504VIRT Display Utility X19A-B-004-05 13504VIRT 13504VIRT Example Comments This page Left Blank Document Number X19A-B-005-05 13504PLAY Diagnostic Utility This page Left Blank 13504PLAY Reads/writes the registers Scripting 13504PLAY Example Comments Document Number X19A-B-006-04 13504BMP Demonstration Program This page Left Blank 13504BMP Program Messages Document Number X19A-B-007-04 13504PWR Software Suspend Power Sequencing Utility X19A-B-007-04 Issue Date 01/02/01 13504PWR Selects software suspend Error Unknown command line argument This page Left Blank Document Number X19A-B-008-02 13504DCFG Configuration Program This page Left Blank Table of Contents This page Left Blank Clocks Tab Panel Tab List of Figures This page Left Blank Installation 13504DCFGUsage 13504DCFG Configuration Tabs General Tab General Tab Memory Tab Memory Tab Clocks Tab Clocks Tab Clki Clocks TabLCD Mclkpclk CRT Mclkpclk Panel Tab Panel Tab STN/TFT Panel TabHRTC/FPLINE VRTC/FPFRAME CRT Tab CRT Tab Defaults Tab Defaults TabSelect the default display device. Three display modes LCD Initializes the registers based on the default mode Registers Tab Registers Tab Miscellaneous Flags Tab Miscellaneous Flags Tab Saving to a File Comments Resolution Frame Rate Hz Pclk MHz Supported Dram Types Document Number X19A-E-001-04 Windows CE Display Drivers X19A-E-001-04 Program Requirements DIP SwitchExample Driver Builds Windows Version With this line Build For Cepc If CEPCDDIVGA2BPP Epson Research and Development Example Installation Installation for Hitachi D9000 and Etma ODOInstallation for Cepc Environment Comments This page Left Blank Document Number X19A-E-002-03 Wind River WindML v2.0 Display Drivers X19A-E-002-03 Issue Date 01/04/06 Wind River WindML v2.0 Display Drivers Make CPU=PENTIUM ugl Building a WindML v2.0 Display Driver Epson Research and Development This page Left Blank Document Number X19A-E-003-02 Wind River UGL v1.2 Display Drivers X19A-E-003-02 Wind River UGL v1.2 Display Drivers Building a UGL v1.2 Display Driver Epson Research and Development This page Left Blank Document Number X19A-G-004-06 S1D13504 X19A-G-004-06 Issue Date 01/02/02 Parts List Schematic Diagrams Installation and Configuration This page Left Blank S1D13504B00C Schematic Diagram 1 of 6 This page Left Blank Features Configuration DIP Switch Settings Installation and ConfigurationJumper Settings Host Bus Selection LCD / Ramdac Interface Pin Mapping LCD Signal Connector J6 CPU / BUS Interface Connector Pinouts CPU/BUS Connector H1 PinoutConnector Comments Pin No CPU/BUS Connector H2 Pinout DB150 D150 D3116 WE1# Host Bus Interface Pin Mapping ISA Bus Support Technical Description Dram Support Non-ISA Bus SupportDecode Logic Clock Input Support Color Passive LCD Panel Support Monochrome LCD Panel SupportColor TFT LCD Panel Support External Cmos Ramdac Support Core VDD Power Supply Power Save ModesIO VDD Power Supply Adjustable LCD Panel Negative Power Supply 15 CPU/Bus Interface Header Strips Schematic Notes Item # Qty/board Designation Part Value Description Parts List Texas Instrument PAL 24 pin DIP package/socketed TIBPAL22V10-15BCNT Diagrams Schematic S1D13504B00C Schematic Diagram 2 Rev.1.0 S1D13504B00C Schematic Diagram 4 Diagram 5 S1D13504B00C Schematic Diagram 6 This page Left Blank Document Number X19A-G-003-05 S5U13504-D9000 S5U13504-D9000 X19A-G-003-05 Issue Date 01/02/02 D9000 Specifics Introduction Features This page Left Blank S5U13504-D9000 Perspective View This page Left Blank Reference Display Buffer S1D13504 Color Graphics LCD Controller LCD Display Support LCD Interface Pin Mapping LCD Connector Pinout CRT Support Adjustable LCD Bias Power Supply Connector Pinout for Channel A6 and A7 Interface SignalsInterface Signals D9000 Specifics Connector Pinout for Channel A7 GNDDC12V Channel A7 Pin # Fpga Signal S1D13504 Signal SmZ Connectors Pinout for Channel A6 Channel A6 Pin # Fpga Signal S1D13504 Signal SmXYBS# GND Channel A6 Pin # Fpga Signal S1D13504 Signal SmZ Bus Interface Timing Board DimensionsMemory Address CS#, M/R# Decode Makefpga file Item # Qty Reference Part Description Parts List Schematic S5U13504-D9000 Schematic Diagram 2 S5U13504-D9000 Schematic Diagram 3 D9000 Component Placement PCB Layout Component Placement S5U13504-D9000 Perspective View Perspective View Document Number X19A-G-006-04 Power Consumption S1D13504 Power Consumption X19A-G-006-04 S1D13504 Power Consumption S1D13504 Total Power Consumption SummaryConditions Document Number X19A-G-005-08 Interfacing to the Philips Mips PR31500/PR31700 Processor This page Left Blank Direct Connection to the Philips PR31500/PR31700 This page Left Blank List of Tables S1D13504 to PR31500/PR31700 Connection using One IT8368E This page Left Blank Introduction Interfacing to the PR31500/PR31700 S1D13504 Host Bus Interface WAIT# RESET#Generic MPU Host Bus Interface Pin Mapping S1D13504 Generic MPU Pin Names Generic MPU Host Bus Interface Signals Hardware Description Direct Connection to the Philips PR31500/PR31700 Memory Mapping and Aliasing S1D13504 Configuration MD1 MD2MD3 MD4 Hardware Description-Using One IT8368E System Design Using the IT8368E PC Card Buffer Logic Chip Select Vancouver Design Center PR31500/PR31700 S1D13504 Hardware Description-Using Two IT8368E’s IT8368E Configuration IT8368E Uses PC Card Slot # Philips Address Size Function TX3912 Address Size Function CARDnIOEN=0 CARDnIOEN=1 S1D13504 Configuration using the IT8368E Software References DocumentsDocument Sources Epson LCD/CRT Controllers S1D13504 Technical SupportPhilips Mips PR31500/PR31700 Processor ITE IT8368E This page Left Blank Document Number X19A-G-007-07 Interfacing to the NEC VR4102 Microprocessor X19A-G-007-07 Issue Date 01/02/02 Introduction Interfacing to the NEC VR4102 This page Left Blank NEC VR4102 Read/Write Cycles This page Left Blank Introduction Interfacing to the NEC VR4102 NEC VR4102 System BusOverview Lcdrdy LCD Memory Access Cycles S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals VR4102 to S1D13504 Interface Read/WriteDecode Logic Generic bus interface e.g. MPC821, ISA bus interface S1D13504 Hardware Configuration NEC Signals Cycle S1D13504 Signals NEC VR4102 ConfigurationWR# Write Software References Japan North America Taiwan, R.O.C NEC Electronics Inc. VR4102 This page Left Blank Interfacing to the Motorola MCF5307 Coldfire Microprocessor X19A-G-011-07 Issue Date 01/02/02 S1D13504 Bus Interface This page Left Blank List of Tables This page Left Blank Introduction Interfacing to the MCF5307 MCF5307 System BusNormal Non-Burst Bus Transactions MCF5307 Memory Read Cycle Burst Cycles Chip-Select Module S1D13504 Bus Interface Generic MPU Host Bus Interface Signals Hardware Connections MCF5307 To S1D13504 Interface S1D13504 Configuration Settings Memory/Register Mapping MCF5307 Chip Select Configuration Software Motorola Inc. Motorola Literature Distribution Center, 800 Motorola MCF5307 Processor S1D13504 Color Graphics LCD / CRT Controller X19A-G-013-02 Issue Date 01/02/02 Introduction Interfacing to the MC68328 This page Left Blank Generic MPU Host Bus Interface Pin Mapping This page Left Blank Introduction 68328 System Bus Interfacing to the MC68328 S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals MC68328 To S1D13504 Interface Busclk RESET# CSB3 Dtack UWE LWE CLK0 MD7 MD6 Option Memory Selection MC68328 Chip Select Configuration Software References Motorola MC68328 Processor This page Left Blank Interfacing to the Motorola MPC821 Microprocessor X19A-G-010-05 Issue Date 01/02/02 Introduction Interfacing to the MPC821 This page Left Blank List of Tables This page Left Blank Introduction Interfacing to the MPC821 MPC8xx System BusMPC821 Bus Overview Power PC Memory Read Cycle Power PC Memory Write Cycle General-Purpose Chip Select Module Gpcm Memory Controller Module User-Programmable Machine UPM S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals Typical Implementation of MPC821 to S1D13504 Interface MPC821 to S1D13504 Interface AB8 AB9AB7 AB6 Sysclk SresetCS4 WE0 S1D13504 Hardware Configuration Register/Memory Mapping MPC821 Chip Select Configuration Source Code Test Software Epson Research and Development Software References Motorola MPC821 Processor Document Number X19A-G-009-05 Interfacing to the PC Card Bus This page Left Blank Introduction Interfacing to the PC Card Bus This page Left Blank PC Card Read Cycle This page Left Blank Introduction Interfacing to the PC Card Bus Memory Access CyclesPC Card System Bus PC Card Overview PC Card Read Cycle S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals Typical Implementation of PC Card to S1D13504 Interface PC Card to S1D13504 Interface Generic MPU SH-3 Equations PAL Equations Software PCMCIA/JEIDA, PC Card Standard -- March Pcmcia PC Card Standard This page Left Blank Document Number X19A-G-012-04 Interfacing to the Toshiba Mips TX3912 Processor This page Left Blank Direct Connection to the Toshiba TX3912 This page Left Blank S1D13504 to TX3912 Connection using One IT8368E This page Left Blank Introduction Interfacing to the TX3912 S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals Direct Connection to the Toshiba TX3912 Memory Mapping and Aliasing S1D13504 Hardware Configuration System Design Using the IT8368E PC Card Buffer S1D13504 to TX3912 Connection using One IT8368E Hardware Description-Using Two IT8368E’s S1D13504 to TX3912 Connection using Two IT8368E IT8368E Configuration 64Mb Card 2 Attribute 64Mb64Mb Card 1 Memory 64Mb Card 2 Memory S1D13504 Configuration Software References Toshiba Mips TX3912 Processor ITE IT8368E This page Left Blank