Power Save Modes, Core VDD Power Supply | Epson S1D13504 specification

Page 16	Epson Research and Development
	Vancouver Design Center

6.10 Power Save Modes

The S1D13504F00A supports one hardware and one software suspend Power Save Mode.

The hardware suspend mode is not supported by the S5U13504B00C.

The software suspend mode is controlled by the utility 13504PWR Software Suspend Power

Sequencing.

6.11 Core VDD Power Supply

An independent fixed 3.3V power supply for Core VDD is provided. A National LP2960AIN-3.3 voltage regulator is used for the power supply and is capable of supplying 500mA @ 3.3V.

6.12 IO VDD Power Supply

The IO VDD voltage is selectable between 3.3V and 5.0V through jumper JP2. For the 5.0V host bus interface, select IO VDD at 5.0V, and for the 3.3V host bus interface, select IO VDD at 3.3V.

Refer to Table 2-3 “Jumper Settings,” on page 8.

6.13 Adjustable LCD Panel Negative Power Supply

Most monochrome passive LCD panels require a negative power supply to provide between -18V and -23V (Iout=45mA). For ease of implementation, such a power supply has been provided as an integral part of this design. The signal VLCD can be adjusted by R37 to supply an output voltage from -14V to -23V and is enabled/disabled by the S1D13504 control signal LCDPWR.

Determine the panel’s specific power requirements and set the potentiometer accordingly before connecting the panel.

6.14 Adjustable LCD Panel Positive Power Supply

Most passive LCD passive color panels and most single monochrome 640x480 passive LCD panels require a positive power supply to supply between +23V and +40V (Iout=45mA). For ease of imple- mentation, such a power supply has been provided as an integral part of this design. The signal VDDH can be adjusted by R31 to provide an output voltage from +23V to +40V and is enabled/disabled by the S1D13504 control signal LCDPWR.

Determine the panel’s specific power requirements and set the potentiometer accordingly before connecting the panel.

S1D13504	S5U13504B00C Rev.1.0 ISA Bus Evaluation Board User Manual
X19A-G-004-06	Issue Date: 01/02/02

Image 322

Epson S1D13504 Power Save Modes, Core VDD Power Supply, IO VDD Power Supply, Adjustable LCD Panel Negative Power Supply

Contents

Technical Manual Document Number X19A-Q-002-14 This page Left Blank Customer Support Information This page Left Blank Memory Interface Power Down ModesGeneral Purpose IO pins CPU Interface CPU Ramdac Hardware Functional Specification Document Number X19A-A-002-18 X19A-A-002-18 Issue Date 01/01/30 Table of Contents Registers Display Buffer Display Configuration 116Power Save Modes 128 Clocking 119 This page Left Blank List of Tables Vancouver Design Center List of Figures Vancouver Design Center Scope IntroductionOverview Description CPU Interface FeaturesMemory Interface Display Support Miscellaneous Display ModesClock Source Package and Pin Typical System Implementation Diagrams LCD Management MC68000 Typical System Diagram Generic Bus, 1Mx16 FPM/EDO-DRAM Functional Block Descriptions Host Interface Functional Block DiagramBlock Description Memory Controller Look-Up Table Power SaveLCD Interface Pin Out Pinout Diagram for S1D13504F00APackage type 128 pin surface mount QFP15 Pinout Diagram for S1D13504F01A Package type 128 pin surface mount TQFP15 Pinout Diagram for S1D13504F02A Package type 144 pin surface mount QFP20 AB0 Pin DescriptionKey TS2 BS# CS#Busclk RD/WR# RESET# WAIT# TS2 WE# CO1 LCAS# CO1UCAS# CO1 RAS# CO1 MA9 TS1 Clock Input LCD Interface Pin Descriptions CRT and External Ramdac Interface Vrtc CRT and Ramdac Interface Pin DescriptionsHrtc BLANK# CN3 Power Supply Pin # Pin Name Type Driver Description F00A F02A F01A Summary of Configuration Options Asym 256Kx16 Multiple Function Pin MappingS1D13504 SH-3 MC68K Bus Generic MPU Pin Names Asym 1Mx16 11 LCD, CRT, Ramdac Interface Pin Mapping Symbol Parameter Rating Units C. CharacteristicsSymbol Parameter Condition Min Typ Max Units Output Pin Capacitance Low Level Output VoltageOutput Leakage Current Bidirectional Pin Capacitance RD/WR# BS# CPU Interface Timing 1 SH-3 Interface TimingWAIT# Symbol Parameter Min Max Units AS# UDS# LDS# 2 MC68K Bus 1 Interface Timing e.g. MC68000T13 T14 T15 D150read D150 hold from falling edge of DTACK# write cycle AS# high setup to CLKAS# high to DTACK# high impedance D150 valid to DTACK# falling edge read cycle AS# DS# 3 MC68K Bus 2 Interface Timing e.g. MC68030A200 SIZ10 M/R# T13 T14 T15 D3116 hold from falling edge of DSACK1# write cycle D3116 valid to DSACK1# falling edge read cycle A200 Generic MPU Interface Synchronous TimingBclk RD0#,RD1# WE0#,WE1# Hi-Z Low write cycle D150 hold from WE0#, WE1# high write cycle A200 Valid Generic MPU Interface Asynchronous TimingHi-Z Valid T10 D150read T82 Symbol Parameter Min Typ Max Units Clock Input Requirements Memory Interface Timing EDO-DRAM Read Timing RAS# CAS# EDO Dram Read Timing EDO-DRAM Write Timing RAS# CAS# WE# T14 Write Data setup time 45 t1 T15 Write Data hold time 55 t1 + CAS# precharge time 45 t1 EDO-DRAM Read-Write Timing EDO-DRAM Read-Write Timing EDO Dram Read-Write Timing EDO-DRAM CAS Before RAS Refresh Timing 10 EDO-DRAM CAS Before RAS Refresh Timing EDO-DRAM Self-Refresh Timing 11 EDO-DRAM Self-Refresh Timing FPM-DRAM Read Timing 12 FPM-DRAM Read Timing 12 FPM Dram Read Timing FPM-DRAM Write Timing 13 FPM-DRAM Write Timing T14 Write Data setup time 45 t1 T15 Write Data hold time FPM-DRAM Read-Write Timing 14 FPM-DRAM Read-Write Timing 45 t1 S1D13504 FPM-DRAM CAS# Before RAS# Refresh Timing RAS# precharge time REG22h bits 32 = 01 or 45 t1 FPM-DRAM Self-Refresh Timing 16 FPM-DRAM CBR Self-Refresh Timing Display Interface Power-On/Reset Timing Fpframe active Suspend Timing Mclk Vndp = Single Monochrome 4-Bit Panel TimingVDP = HDP = Sync Timing Data Timing Vndp Single Monochrome 8-Bit Panel TimingVDP HDP = REG05h bits 40 + 1*8 23 Ts UD30, LD30 setup to Fpshift falling edgeUD30, LD30 hold to Fpshift falling edge = REG05h bits 40 + 1*8 14 Ts Single Color 4-Bit Panel Timing 23 Single Color 4-Bit Panel Timing = REG05h bits 40 + 1*8 26 Ts = REG04h bits 60+1*8 1 Ts= REG05h bits 40 + 1*8 17 Ts Single Color 8-Bit Panel Timing Format 25 Single Color 8-Bit Panel Timing Format FPSHIFT2 falling edge to Fpline rising edge UD30, LD30 setup to FPSHIFT2 rising, Fpshift falling edgeFpline pulse width Fpline period FPSHIFT2, Fpshift pulse width high 27 Single Color 8-Bit Panel Timing Format T1min = t3min 9Ts Single Color 16-Bit Panel Timing VDP Vndp LINE1 LINE2 LINE3 LINE4 LINE479 LINE480 HDP Hndp UD70, LD70 setup to Fpshift falling edge UD70, LD70 hold to Fpshift falling edge Dual Monochrome 8-Bit Panel Timing Fpshift UD3 UD2 UD1 UD0 LD3 LD2 LD1 LD0 = REG05h bits 40 + 1*8 8 Ts Dual Color 8-Bit Panel Timing 33 Dual Color 8-Bit Panel Timing = REG05h bits 40 + 1*8 9 Ts Dual Color 16-Bit Panel Timing 35 Dual Color 16-Bit Panel Timing UD70 LD70 12 16-Bit TFT Panel Timing = Vertical Display Period = REG09h bits 10, REG08h bits 70 + 38 TFT A.C. Timing = REG07h bits 30+1*8 Ts = REG04h bits 60+1*8 + REG05h bits 40+1*8 Ts= REG0Ch bits 20+1 lines CRT Timing 39 CRT Timing 40 CRT A.C. Timing Dacclk period Write External Ramdac Read / Write TimingRead DACWR# pulse width low Register Descriptions RegistersRegister Mapping Revision Code Register Memory Configuration Register Memory Configuration RegistersTime/256 Cycles MOD Rate Register Panel/Monitor Configuration RegistersPanel Type Register REG03h MOD Rate Bit Horizontal Non-Display Period Register Horizontal Display Width RegisterHRTC/FPLINE Start Position Register Vertical Display Height Register HRTC/FPLINE Pulse Width RegisterHrtc Fpline VRTC/FPFRAME Start Position Register Vertical Non-Display Period RegisterVrtc Fpframe Fpframe Vrtc VRTC/FPFRAME Pulse Width RegisterREG0Ch Vrtc Polarity Simultaneous Display Option Select Bits Display Configuration RegistersDisplay Mode Register Even Scan Only Number of Bits-Per-Pixel Selection Screen 1 Line Compare Register Screen 1 Display Start Address Register Screen 2 Display Start Address Register Screen 2 Display Start Address Register 0 RWMemory Address Offset Register Pixel Panning Register Clock Configuration RegisterClock Configuration Register Number of Bits-Per-Pixel Screen 2 Pixel Panning Bits Used Miscellaneous Disable Register Power Save Configuration RegistersPower Save Configuration Register Miscellaneous Registers REG1Dh MD15 MD14 MD13 MD12 MD11 MD10 MD Configuration Readback RegisterGpio Configuration Register MD9 MD8 Vancouver Design Center REG1Fh GPIO11 Pin GPIO10 Pin GPIO9 Pin GPIO8 Pin IO Config Gpio Status / Control Register GPO Gpio Status / Control RegisterREG21h GPIO11 Pin GPIO10 Pin GPIO9 Pin GPIO8 Pin Control IO Status REG22h Bits Performance Enhancement RegisterREG22h EDO Read RC Timing RAS# to Minimum Random Cycle Width t RC REG22h Bit RAS# to CAS# Delay tRCDOptimal Dram Timing RAS# Precharge Width t RP Look-Up Table Registers RGB Index Bits Look-Up Table Access Pointer SequenceLook-Up Table Address Register REG26h LUT Data Bit Look-Up Table Data RegisterLook-Up Table Bank Select Register REG27h Red Bank Blue Bank Green Bank Select Bit External Ramdac Control Registers Ramdac Read Mode Address RegisterRamdac Write Mode Address Register Ramdac Pixel Read Mask Register Ramdac Palette Data Register REG2Eh or REG2Fh Display Buffer 512K byte Memory AB200 Image Buffer Half Frame Buffer Display Configuration Display Mode Data Format 15/16 Bit-Per-Pixel Format Memory Organization Display Image ManipulationImage Buffer Display type ClockingMaximum Mclk Pclk Ratios Maximum Pclk Allowed Bpp 16 bpp Speed Grade Bpp Clock Hndpt s Panel Frame Rate Calculation= Pclk MHz FPM-DRAM Look-Up Table Architecture Bit-Per-Pixel ModeDisplay Mode Bit Wide Look-Up Table Gray Shade Display Modes Bit-Per-Pixel Mode Bit-Per-Pixel Color Mode Color Display Modes Bank Selected Bank Entry Bit Red data output Logic Red Look-Up Table 0000 0001 0010 0011 0100 0101 Entry 0110 Color Data Format Red Look-Up Table Hardware Suspend Power Save ModesSoftware Suspend Power Save Mode PSM Power Save Mode Function SummaryPin States in Power Save Modes Pin State Pins Normal Software Hardware Active Suspend 14.1 QFP15-128 S1D13504F00A Mechanical DataQFP15 128 pin Unit mm TQFP15 128 pin Unit mm TQFP15-128 S1D13504F01A±0.2 QFP20 144 pin Unit mm QFP20-144 S1D13504F02A125 Programming Notes and Examples Document Number X19A-G-002-07 This page Left Blank Introduction Programming the S1D13504 Registers LCD Power Sequencing and Power Save ModesAdvanced Techniques Sample Code CRT ConsiderationsIdentifying the S1D13504 Hardware Abstraction Layer HAL Appendix a Supported Panel Values Initializing the S1D13504 Registers This page Left Blank Introduction 2 REG22 bits 7-2 Performance Enhancement Register Programming the S1D13504 Registers3 REG02 bit 1 Dual/Single Panel Type 5 REG23 Display Fifo 4 REG1B bit 0 Half Frame Buffer DisableRegister Initialization Initialization Sequence Initializing the S1D13504 Registers Initialization ExampleOperation Description Re-Programming Registers Disabling the Half Frame Buffer Sequence Bit Display Buffer LocationPixel Bit Memory Organization for Eight Bit-per-pixel 256 Colors Bit Red Bit Green Bit Blue Bit Memory Organization for 16 Bit-per-pixel 65536 Colors Memory Organization for 15 Bit-per-pixel 32768 ColorsBit Reserved Red Bit Green Bit Blue Bit REG26h Look-Up Table Data Register Read/Write Look-Up Table LUTREG24h Look-Up Table Address Register Read/Write REG27h Look-Up Table Bank Register Read/Write Bank Select Bits Look-Up Table Organization Look-Up Table ConfigurationsBank Color Modes Recommended LUT Values for 1 bpp Color ModeRecommended LUT Values for 2 bpp Color Mode Address Red Green Blue 11 Recommended LUT Values For 8 bpp Color Mode 13 Recommended LUT Values for 1 bpp Gray Shades 12 Examples of 256 Pixel Colors Using Linear LUTGray Shade Modes Pixel Value Color 15 Recommended LUT Values for 8 bpp Gray Shade 14 Recommended LUT Values for 2 bpp Gray ShadesLUT Address Green LUT Data Bpp Gray Shade Advanced Technique s Virtual Display REG16h Memory Address Offset Register RegistersExamples REG17h Memory Address Offset Register Panning and Scrolling Number of Pixels Panned Using Start Address Active Pixel Pan Bits Example 4 Panning Right and Left Line Compare Bit Split ScreenREG0E Screen 1 Line Compare Register REG0F Screen 1 Line Compare Register REG14h Screen 2 Display Start Address Register REG13h Screen 2 Display Start Address RegisterREG15h Screen 2 Display Start Address Register Introduction to Power Save Modes LCD Power Sequencing and Power Save ModesIntroduction to LCD Power Sequencing Display Mode Register Shortening the 128 Frame Delay using Hardware SUSPEND# Suspend Enable SequenceShortening the 128 Frame delay using Software Suspend Suspend Sequencing LCD Enable / Disable using Power Save Modes Suspend Disable SequenceLCD Enable/Disable Sequencing Reg0D bit LCD Enable / Disable using Manual Control CRT Only CRT ConsiderationsIntroduction Ramdac Register Mapping for Little/Big-Endian Simultaneous Display Related Register Data for CRT Only Address Address Related register data for Simultaneous Display Register 640X480@75Hz 640X480@60Hz Identifying the S1D13504 API for 13504HAL Hardware Abstraction Layer HALInitialization Int seDeRegisterDeviceint device Int seGetIdint device, Byte *pId Int seInitHalvoid Int seValidRegisteredDeviceint device Int seSetInitint deviceInt seValidStdDeviceint device Int seGetLastUsableByteint device, Dword *pLastByte Int seGetBitsPerPixelint device, Byte *pBitsPerPixelInt seGetBytesPerScanlineint device, int *pBytes Int seGetLinearDispAddrint device, Dword *pDispLogicalAddr Int seReadDisplayByteint device, Dword offset, Byte *pByte Int seGetScreenSizeint device, int *width, int *heightInt seReadDisplayWordint device, Dword offset, Word *pWord Int seSetBitsPerPixelint device, Byte BitsPerPixel Int seSplitInitint device, Dword Scrn1Addr, Dword Scrn2Addr Int seVirtInitint device, int xVirt, long *yVirt Int seVirtMoveint device, Byte WhichScreen, int x, int y Vancouver Design Center Int seGetDacEntryint device, Byte index, Byte *pEntry Color Manipulation Int seGetDacint device, Byte *pDacInt seGetLutint device, Byte *pLut Int seSetDacint device, Byte *pDac Int seGetLutEntryint device, Byte index, Byte *pEntryInt seSetDacEntryint device, Byte index, Byte *pEntry Int seSetLutint device, Byte *pLut Int seSetLutEntryint device, Byte index, Byte *pEntry Int seDrawTextint device, char *fmt Int sePutcharint ch Int seGetcharvoidInt sePutcint device, int ch Int seSetPixelint device, int x, int y, Dword color Miscellaneous Int seDelayint device, Dword SecondsInt seSetRegint device, int index, Byte val Word seRotateByteLeftBYTE val, Byte bits Word seRotateByteRightBYTE val, Byte bits Sample code using 13504HAL API Sample Code Sample code without using 13504HAL API Vancouver Design Center Pclk To arrive at the frame rate closest to the desired Words Fifo Passive Single Panel Appendix a Supported Panel ValuesSupported Panel Values Passive Dual Panel TFT Panel TFT 16-Bit Register Single 01/02/02 Number of Bits/Pixel 13504CFG.EXE Configuration Program Document Number X19A-B-001-04 Vancouver Design Center X19A-B-001-04 Script Mode Interactive Mode 13504CFG.EXE Program Requirements This page Left Blank 13504CFG View Menu This page Left Blank 13504CFG.EXE Program Requirements InstallationUsage Script Mode Interactive Mode 13504CFG Menu Bar Making 13504CFG Menu Selections Files Menu View Menu 13504CFG Current Configuration Device Menu Panel Edit Panel Setup CRT Edit CRT Setup Advanced Memory Edit Advanced Memory Setup Power Management Edit Power Setup Lookup Table LUT Edit LUT Setup Setup Help Menu Comments Sample Program Messages This page Left Blank 13504SHOW Demonstration Program Document Number X19A-B-002-05 This page Left Blank 13504SHOW S1D13504 Supported Evaluation Platforms Error Too many devices registered Program Messages 13504SPLT Display Utility Document Number X19A-B-003-05 This page Left Blank 13504SPLT 13504SPLT Example Comments This page Left Blank 13504VIRT Display Utility Document Number X19A-B-004-05 S1D13504 13504VIRT Display Utility X19A-B-004-05 13504VIRT 13504VIRT Example Comments This page Left Blank 13504PLAY Diagnostic Utility Document Number X19A-B-005-05 This page Left Blank 13504PLAY Reads/writes the registers 13504PLAY Example Scripting Comments 13504BMP Demonstration Program Document Number X19A-B-006-04 This page Left Blank 13504BMP Program Messages 13504PWR Software Suspend Power Sequencing Utility Document Number X19A-B-007-04 X19A-B-007-04 Issue Date 01/02/01 13504PWR Selects software suspend Error Unknown command line argument This page Left Blank 13504DCFG Configuration Program Document Number X19A-B-008-02 This page Left Blank Table of Contents This page Left Blank List of Figures Clocks Tab Panel Tab This page Left Blank 13504DCFG InstallationUsage 13504DCFG Configuration Tabs General Tab General Tab Memory Tab Memory Tab Clocks Tab Clocks Tab LCD Mclkpclk Clocks TabClki CRT Mclkpclk Panel Tab Panel Tab HRTC/FPLINE Panel TabSTN/TFT VRTC/FPFRAME CRT Tab CRT Tab Select the default display device. Three display modes LCD Defaults TabDefaults Tab Initializes the registers based on the default mode Registers Tab Registers Tab Miscellaneous Flags Tab Miscellaneous Flags Tab Saving to a File Resolution Frame Rate Hz Pclk MHz Supported Dram Types Comments Windows CE Display Drivers Document Number X19A-E-001-04 X19A-E-001-04 Example Driver Builds DIP SwitchProgram Requirements Windows Version With this line Build For Cepc If CEPCDDIVGA2BPP Epson Research and Development Installation for Hitachi D9000 and Etma ODO Example InstallationInstallation for Cepc Environment Comments This page Left Blank Wind River WindML v2.0 Display Drivers Document Number X19A-E-002-03 X19A-E-002-03 Issue Date 01/04/06 Wind River WindML v2.0 Display Drivers Building a WindML v2.0 Display Driver Make CPU=PENTIUM ugl Epson Research and Development This page Left Blank Wind River UGL v1.2 Display Drivers Document Number X19A-E-003-02 X19A-E-003-02 Wind River UGL v1.2 Display Drivers Building a UGL v1.2 Display Driver Epson Research and Development This page Left Blank Document Number X19A-G-004-06 S1D13504 X19A-G-004-06 Issue Date 01/02/02 Installation and Configuration Parts List Schematic Diagrams This page Left Blank S1D13504B00C Schematic Diagram 1 of 6 This page Left Blank Features Jumper Settings Installation and ConfigurationConfiguration DIP Switch Settings Host Bus Selection LCD Signal Connector J6 LCD / Ramdac Interface Pin Mapping CPU/BUS Connector H1 Pinout CPU / BUS Interface Connector PinoutsConnector Comments Pin No CPU/BUS Connector H2 Pinout Host Bus Interface Pin Mapping DB150 D150 D3116 WE1# Technical Description ISA Bus Support Decode Logic Non-ISA Bus SupportDram Support Clock Input Support Color TFT LCD Panel Support Monochrome LCD Panel SupportColor Passive LCD Panel Support External Cmos Ramdac Support IO VDD Power Supply Power Save ModesCore VDD Power Supply Adjustable LCD Panel Negative Power Supply Schematic Notes 15 CPU/Bus Interface Header Strips Parts List Item # Qty/board Designation Part Value Description TIBPAL22V10-15BCNT Texas Instrument PAL 24 pin DIP package/socketed Schematic Diagrams S1D13504B00C Schematic Diagram 2 Rev.1.0 S1D13504B00C Schematic Diagram 4 Diagram 5 S1D13504B00C Schematic Diagram 6 This page Left Blank S5U13504-D9000 Document Number X19A-G-003-05 S5U13504-D9000 X19A-G-003-05 Issue Date 01/02/02 Introduction Features D9000 Specifics This page Left Blank S5U13504-D9000 Perspective View This page Left Blank Reference S1D13504 Color Graphics LCD Controller Display Buffer LCD Display Support LCD Connector Pinout LCD Interface Pin Mapping Adjustable LCD Bias Power Supply CRT Support Interface Signals Interface SignalsConnector Pinout for Channel A6 and A7 D9000 Specifics GND Connector Pinout for Channel A7DC12V Channel A7 Pin # Fpga Signal S1D13504 Signal SmZ Channel A6 Pin # Fpga Signal S1D13504 Signal SmXY Connectors Pinout for Channel A6BS# GND Channel A6 Pin # Fpga Signal S1D13504 Signal SmZ Memory Address CS#, M/R# Decode Board DimensionsBus Interface Timing Makefpga file Parts List Item # Qty Reference Part Description Schematic S5U13504-D9000 Schematic Diagram 2 S5U13504-D9000 Schematic Diagram 3 D9000 PCB Layout Component Placement Component Placement Perspective View S5U13504-D9000 Perspective View Power Consumption Document Number X19A-G-006-04 S1D13504 Power Consumption X19A-G-006-04 S1D13504 Power Consumption Summary S1D13504 Total Power ConsumptionConditions Interfacing to the Philips Mips PR31500/PR31700 Processor Document Number X19A-G-005-08 This page Left Blank Direct Connection to the Philips PR31500/PR31700 This page Left Blank S1D13504 to PR31500/PR31700 Connection using One IT8368E List of Tables This page Left Blank Introduction Interfacing to the PR31500/PR31700 Generic MPU Host Bus Interface Pin Mapping WAIT# RESET#S1D13504 Host Bus Interface S1D13504 Generic MPU Pin Names Generic MPU Host Bus Interface Signals Direct Connection to the Philips PR31500/PR31700 Hardware Description Memory Mapping and Aliasing MD1 MD2 S1D13504 ConfigurationMD3 MD4 System Design Using the IT8368E PC Card Buffer Hardware Description-Using One IT8368E Chip Select Logic Vancouver Design Center Hardware Description-Using Two IT8368E’s PR31500/PR31700 S1D13504 IT8368E Configuration TX3912 Address Size Function CARDnIOEN=0 CARDnIOEN=1 IT8368E Uses PC Card Slot # Philips Address Size Function S1D13504 Configuration using the IT8368E Software Documents ReferencesDocument Sources Philips Mips PR31500/PR31700 Processor Technical SupportEpson LCD/CRT Controllers S1D13504 ITE IT8368E This page Left Blank Interfacing to the NEC VR4102 Microprocessor Document Number X19A-G-007-07 X19A-G-007-07 Issue Date 01/02/02 Introduction Interfacing to the NEC VR4102 This page Left Blank NEC VR4102 Read/Write Cycles This page Left Blank Introduction NEC VR4102 System Bus Interfacing to the NEC VR4102Overview LCD Memory Access Cycles Lcdrdy S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals Read/Write VR4102 to S1D13504 InterfaceDecode Logic S1D13504 Hardware Configuration Generic bus interface e.g. MPC821, ISA bus interface WR# NEC VR4102 ConfigurationNEC Signals Cycle S1D13504 Signals Write Software References NEC Electronics Inc. VR4102 Japan North America Taiwan, R.O.C This page Left Blank Interfacing to the Motorola MCF5307 Coldfire Microprocessor X19A-G-011-07 Issue Date 01/02/02 S1D13504 Bus Interface This page Left Blank List of Tables This page Left Blank Introduction MCF5307 System Bus Interfacing to the MCF5307Normal Non-Burst Bus Transactions MCF5307 Memory Read Cycle Chip-Select Module Burst Cycles S1D13504 Bus Interface Generic MPU Host Bus Interface Signals MCF5307 To S1D13504 Interface Hardware Connections S1D13504 Configuration Settings MCF5307 Chip Select Configuration Memory/Register Mapping Software Motorola Inc. Motorola Literature Distribution Center, 800 Motorola MCF5307 Processor S1D13504 Color Graphics LCD / CRT Controller X19A-G-013-02 Issue Date 01/02/02 Introduction Interfacing to the MC68328 This page Left Blank Generic MPU Host Bus Interface Pin Mapping This page Left Blank Introduction Interfacing to the MC68328 68328 System Bus S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals Busclk RESET# MC68328 To S1D13504 Interface CSB3 Dtack UWE LWE CLK0 MD6 MD7 MC68328 Chip Select Configuration Option Memory Selection Software References Motorola MC68328 Processor This page Left Blank Interfacing to the Motorola MPC821 Microprocessor X19A-G-010-05 Issue Date 01/02/02 Introduction Interfacing to the MPC821 This page Left Blank List of Tables This page Left Blank Introduction MPC8xx System Bus Interfacing to the MPC821MPC821 Bus Overview Power PC Memory Read Cycle Power PC Memory Write Cycle Memory Controller Module General-Purpose Chip Select Module Gpcm User-Programmable Machine UPM S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals MPC821 to S1D13504 Interface Typical Implementation of MPC821 to S1D13504 Interface AB7 AB9AB8 AB6 CS4 SresetSysclk WE0 S1D13504 Hardware Configuration MPC821 Chip Select Configuration Register/Memory Mapping Test Software Source Code Epson Research and Development Software References Motorola MPC821 Processor Interfacing to the PC Card Bus Document Number X19A-G-009-05 This page Left Blank Introduction Interfacing to the PC Card Bus This page Left Blank PC Card Read Cycle This page Left Blank Introduction PC Card System Bus Memory Access CyclesInterfacing to the PC Card Bus PC Card Overview PC Card Read Cycle S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals PC Card to S1D13504 Interface Typical Implementation of PC Card to S1D13504 Interface SH-3 Generic MPU PAL Equations Equations Software PCMCIA/JEIDA, PC Card Standard -- March PC Card Standard Pcmcia This page Left Blank Interfacing to the Toshiba Mips TX3912 Processor Document Number X19A-G-012-04 This page Left Blank Direct Connection to the Toshiba TX3912 This page Left Blank S1D13504 to TX3912 Connection using One IT8368E This page Left Blank Introduction Interfacing to the TX3912 S1D13504 Host Bus Interface Generic MPU Host Bus Interface Signals Direct Connection to the Toshiba TX3912 Memory Mapping and Aliasing S1D13504 Hardware Configuration System Design Using the IT8368E PC Card Buffer S1D13504 to TX3912 Connection using One IT8368E Hardware Description-Using Two IT8368E’s S1D13504 to TX3912 Connection using Two IT8368E IT8368E Configuration 64Mb Card 1 Memory 64Mb64Mb Card 2 Attribute 64Mb Card 2 Memory S1D13504 Configuration Software References Toshiba Mips TX3912 Processor ITE IT8368E This page Left Blank