Honeywell DR4300 manual 100 H*factory setting, Lin factory setting

DR4300 Circular Chart Recorder

Lower Display	Upper Display		Parameter
Prompt	Range of Setting		Definition
	or Selection
IN TYP		INPUT ACTUATION TYPE—This selection specifies what actuation
		you are going to use for the input. Be sure that the values
		configured for the high and low chart range, alarm setpoint, etc. are
		within the measuring range for the selected actuation type.
	B	B thermocouple	105	to	3300°F	41	to	1815°C
	EH	E thermocouple high	–454	to 1832°F		–270	to 1000°C
	EL	E thermocouple low	–200	to	1100°F	–129	to	593°C
	JH	J thermocouple high	0	to	1600°F	–18	to	871°C
	JL	J thermocouple low	20	to	770°F	–7	to	410°C
	KH	K thermocouple high	–320	to 2500°F		–196	to 1371°C
	KL	K thermocouple low	–20	to	1000°F	–29	to	538°C
	NNM	NiNiMo thermocouple	32	to 2500°F		0	to 1371°C
	NIC	Nicrosil-Nisil	0	to	2372°F	–18.8	to	1300°C
		thermocouple
	R	R thermocouple	0	to 3100°F		–18	to 1704°C
	S	S thermocouple	0	to	3100°F	–18	to	1704°C
	TH	T thermocouple high	–420	to	700°F	–251	to	371°C
	TL	T thermocouple low	–200	to	600°F	–129	to	316°C
	W	W thermocouple	0	to 4200°F		–18 to 2316°C
	100 H*[factory setting]	100 Ohm–RTD (high)	–300 to 900°F			–184 to 482°C
	100 L*	100 Ohm-RTD (low)	–130 to 392°F			–90 to 200°C
	100 T**	100 Ohm-RTD (special) –238		to	482°F	–150	to	250°C
	4-20***	4 to 20 Milliamps
* IEC Alpha =	0-20***	0 to 20 Milliamps
	10m***	0 to 10 Millivolts
0.00385	100m***	0 to 100 Millivolts
**IEC Alpha =
	200m***	0 to 200 Millivolts
0.00391
	0-1***	0 to 1 Volt
***These input	0-2***	0 to 2 Volts
selections are not	1-5***	1 to 5 Volts
available on Limit	0-5***	0 to 5 Volts
Control units.
	0-10***	0 to 10 Volts
	2-10***	2 to 10 Volts
XMITTR		Transmitter Input Type—Use this parameter to specify whether
		the input should be used as the PV without characterization (linear)
		or the square root of the input should be used as the PV.
	Lin [factory setting]	Linear—No characterization applied to input.
	Srt	Square Root—PV is the square root of input. For example:
		suppose the linear input range is 0 to 5000 and the input type is 0 to
		5 volts. Then if input = 2.5 V = 50 %,

.50 = .7071= 70.71%

.7071 x 5000 = 3535 = PV

86 DR4300 Circular Chart Recorder Product Manual 12/03