Texas Instruments TMS320DM648 Ancillary Data Display, Horizontal Ancillary Hanc Data Display

www.ti.com

Ancillary Data Display

Figure 4-20. Interspersed Chroma Edge Replication

cd

ab

a

ab

b

c

cd

d

w

wx

x

y

yz

z

yz

wx

Horizontal Image Size

Leading edge

y’

Trailing edge

a

a’

b b’

c

c’

d

w

w’

x x’

y

z

z’

replicated chroma

replicated chroma

samples

samples

Cb’a = (-3Cbcd+ 33Cbab + 101Cbab -3Cbcd

)/128

Cb’z = (-3Cbwx+ 101Cbyz + 33Cbyz -3Cbwz)/128

Cr’a = (-3Crcd+ 33Crab + 101Crab -3Crcd)/128

Cr’z = (-3Crwx+ 101Cryz + 33Cryz -3Cbwx)/128

Cb’b = (-3Cbab+ 101Cbab + 33Cbcd -3Cbef)/128

Cb’y = (-3Cbuv+ 33Cbwx + 101Cbyz -3Cbyz)/128

Cr’b = (-3Crab+ 101Crab + 33Crcd -3Cref)/128

Cr’y = (-3Cruv+ 33Crwx + 101Cryz -3Cbyz)/128

Cb’c = (-3Cbab+ 33Cbab + 101Cbcd -3Cbef)/128

Cb’x = (-3Cbuv+ 101Cbwx + 33Cbyz -3Cbyz)/128

Cr’c = (-3Crab+ 33Crab + 101Crcd -3Cref)/128

Cr’x = (-3Cruv+ 101Crwx + 33Cryz -3Cryz)/128

Cb’d = (-3Cbab+ 101Cbcd + 33Cbef -3Cbgh)/128

Cb’w = (-3Cbst+ 33Cbuv + 101Cbwx -3Cbyz)/128

Cr’d = (-3Crab+ 101Crcd + 33Cref -3Crgh)/128

Cr’w = (-3Crst+ 33Cruv + 101Crwx -3Cryz)/128

4.5Ancillary Data Display

The following sections discuss ancillary data display. No special provisions are made for the display of horizontal ancillary (HANC) or vertical ancillary (VANC), also called vertical blanking interval (VBI), data.

4.5.1 Horizontal Ancillary (HANC) Data Display

HANC data can be displayed using the normal video display mechanism by programming IMGHSIZEn to occur prior to the SAV code. The HANC data including the ancillary data header must be part of the YCbCr separated data in the FIFOs. The VCTHRLD value and EDMA size must be programmed to comprehend the additional samples. You must disable scaling and chroma re-sampling when including the display of HANC data to prevent data corruption.

4.5.2 Vertical Ancillary (VANC) Data Display

VANC (or VBI) data is commonly used for such features as teletext and closed-captioning. No special provisions are made for the display of VBI data. VBI data may be displayed using the normal display mechanism by programming IMGVOFF to occur before the first line of active video on the first line of desired VBI data. Note that the VBI data must be YCbCr separated. You must disable scaling and chroma re-sampling when the display of VBI data is desired or the data will be corrupted by the filters.

4.6Raw Data Display Mode

The raw data display modes are intended to output data to a RAMDAC or other D/A-type device. This is typically RGB formatted data. No timing information is inserted into the output data stream; instead, selectable control signals are output to indicate timing. Raw data display includes a synchronized dual channel option. This allows channel B to output a separate data stream using the same clock and control as channel A. This mode is useful when used with a second video port in systems that require 24-bit RGB output.

The raw data mode uses a single FIFO of 5120 bytes for storage of output data. The FIFO is filled by EDMAs writing to the Y FIFO destination register A (YDSTA). EDMAs are requested using the YEVTA event. In raw sync mode (RSYNC bit is set), the FIFO is split into 2560-byte channel A and B buffers. The channel B FIFO is filled by EDMAs using the Y FIFO destination register B (YDSTB) as a destination. Both YEVTA and YEVTB events are generated using the channel A timing control.

106 Video Display Port SPRUEM1 –May 2007

Submit Documentation Feedback