Ethernet, Status display | Honeywell UDA2182 guide

				Configuration

Sub-menu		Parameter	Selection or Range	Parameter Definition
selection			of Setting
	Address		0 to 999 (default = 0)	Modbus RTU Slave ID – 0 is offline

	Baud Rate		2400 (default)	Modbus RTU Baud Rate
			4800
			9600
			19200
			38400
			57600
			115200

Ethernet	Port Reset		Off (default)	Enable selection resets the Communication card.
			Enable	It should be enabled when configurations for
				Ethernet are modified.

	DHCP		No (default)	When YES, Dynamic Host Configuration Protocol
			Yes	server automatically assigns a dynamic IP
				address to UDA.
				The set dynamic IP can be seen from “Comm
				Status” display.

	IpAddr Octet 1		0 to 255	These parameters are visible only when DHCP
	IpAddr Octet 2			option is NO.
	IpAddr Octet 3			Allows you to assign Static IP address to the
	IpAddr Octet 4			Allows you to assign Static IP address to the
	IpAddr Octet 4			UDA.
				UDA.

	SbntMsk Octet 1		0 to 255	These parameters are visible only when DHCP
	SbntMsk Octet 2			option is NO.
	SbntMsk Octet 3			Allows you to assign Subnet Mask as per the
	SbntMsk Octet 4			Allows you to assign Subnet Mask as per the
	SbntMsk Octet 4			local network settings
				local network settings

	Dflt Gtwy Octet 1		0 to 255	These parameters are visible only when DHCP
	Dflt Gtwy Octet 2			option is NO.
	Dflt Gtwy Octet 3			Allows you to assign the Default Gateway as per
	Dflt Gtwy Octet 4			Allows you to assign the Default Gateway as per
	Dflt Gtwy Octet 4			the local network settings
				the local network settings

		DNS Srvr Octet 1	0 to 255	These parameters are visible only when DHCP
		DNS Srvr Octet 2		option is NO.
		DNS Srvr Octet 3		Allows you to assign the DNS server IP address
		DNS Srvr Octet 4		Allows you to assign the DNS server IP address
		DNS Srvr Octet 4		as per the local network settings
				as per the local network settings

January 2009

UDA2182 Universal Dual Analyzer Product Manual

107

Image 119

Honeywell UDA2182 manual Ethernet, Status display

Contents

January UDA2182 Universal Dual Analyzer Product Manual Copyright 2008 by Honeywell Revision January WARRANTY/REMEDY Telephone AbstractContacts World Wide Web Symbol Definition Symbol Definitions Contents 100 136 114 191 178185 189 239 Tables Figures Resetting ORP Offset Overview Introduction Communications Card Optional OutputsRelays Infrared Communications Features High Noise Immunity Password protectionAuto Clean/Auto Cal Diagnostic/Failsafe Outputs UDA2182 Universal Dual Analyzer SpecificationsSpecifications Resistive Load Rating 4A, 120/240 Vac Declaration of Conformity CE Conformity Europe Specifications What’s in this section? Unpacking, Preparation, and MountingIntroduction Step Action Procedure Procedure for Unpacking and Preparing the UDA2182Unpacking and Preparing Mounting Panel Cutout Panel Mounting Dimensions Rear Panel Support Plate Dimensions Pipe Mounting Pipe Mounting Dimensions not to scale Wall Mounting Dimensions not to scale Wall Mounting Dimensions Power Wiring Avoid damage to components General Wiring PracticesSafety precaution Wiring for immunity compliance Installing Power Wiring Power Wiring Considerations Disengage from the terminal boards Power Wiring Operating the Analyzer UDA2182 Operator Interface all display items shown Analyzer Overview Function Key NavigationFunction of Keys Key Displays Overview Status Messages Online Functions Display Details FunctionsProcess Variable Values Two Input Display Input Displays Selecting Control Display PID DisplaysOverview Changing PID Parameters on the Display To access the PID Parameters. You will seeTo access the value or selection of each Changing Parameters on the PID Display Auto Cycle Displays Access to Auto Cycle Displays Displays How it works Cycle Interval Hold ActiveProbe Transit Cycle Start Src Manually Starting/Stopping the Auto Cycle To access the Auto Cycle Operator Panel. You will seeManual Starting/Stopping the Auto Cycle Condition Output Hold State EnabledAuto Cycle Fail Step AC n Extract Rinse Cal Pharma Display Pharmacopoeia Test Procedure Pharma Display screen example Displays Access to Pharma Display To select Test pH After Stage 3 is selected Selecting the Pharma Test on DisplayTo select Test µS/cm After Stage 2 is selected Pharma Warning and Fail Signal UDA for Cation and Degassed CO2 How it works Cation Calc Display Degassed CO2 PH Calculation from Specific and Cation Conductivity Setup 5 CO2 by Degassed Conductivity Access to Cation DisplayCalibration Check pH Electrode System Troubleshooting Status Display Details Access to Status DisplaysPID Alarm 10Status Display Relay States Input StatusOutput Levels Comm Status Output of the Switch and Function Generator blocksAux Values Variables Auto Cycling ConfiguredStatus Parameter Status Definition Display Read Only MACaddr Hi and MACaddr Low is the MAC address Available only if both units of measure between Press Until you see Access to Event History DisplaysSetup Chg 04.19 Alarm 1 On 03.15 Hold On Power On 03.09 Event History Clear Event History 12Process Instrument Explorer Software Features Infrared communications Ethernet port provides Modbus CommunicationsSummary Serial port provides Configuration UDA2182 Block Diagram UDA2182 Block Diagram Setup Group Overview Main Setup MenuAccessing the Main Menu Configuration General Rules for Editing Basic Configuration Procedure Enter Basic Configuration Procedure Exit Signal Type Applies Source to Selections Analog and Digital Signal SourcesSignal Sources Analog Signal Description Definition Analog Signal Sources Digital Signal Description Definition Digital Signal Sources Out 2 Fault DgtlVar Input Configuration Inputs ConfigurationAccessing Inputs Menu Default = Default = 77ºFDefault = 25ºC None default 8550 Ω Therm Sub-menu ParameterFollowing important differences Default to Cell Const Cell Const 0 Cond mS/m NIST-default +ISO-Default + Cond Only PV Type 000default Selection Range Setting H2SO4 NaCl default Configured minutes value set here. When the Timer Default = NoneDefault 10.000 Pharma Timer begins to count down from Manual Input Do ConcenOxygen do concentration or percent saturation 5000Ω Therm Default = 20.000 Outputs Configuration Outputs ConfigurationAccessing Outputs Menu Parameters in % Parameters in engineering units Accessing Relays Menu Relays Configuration Overview Relays Configuration Frequency ON/OFF Pulse Output Range Switch using Math, Monitor, and Switch Blocks Alarms Configuration High default Accessing Alarms MenuAlarms Configuration Monitors Configuration 10Monitors ConfigurationAccessing Monitors Menu For Low Monitor Accessing Math Menu 11Math Configuration Linear default 10 Math Configuration Accessing Logic Menu Logic Configuration Latch 11 Logic Configuration Func Gen Function Generator Auxiliary ConfigurationSwitch Sub-menu Parameter Selection or Range of Setting Accessing Auxiliary Menu12 Auxiliary Configuration 99999 to 999999 Default= PID Tracking PID Control ConfigurationPID Tracking versus Manual Mode Using Auto/Manual Switch Configuration 13 PID Configuration Accessing Control MenuPIDn Config Table PIDnAlarms Table Failsafe default Pida defaultReverse default Manualdefault 9999 to Enable default PID 2 Tune Disable default 14 PID Tuning PID 2 Alarms 15 PID AlarmsNo Alarm default Setpoint No Alarm default Same as Alarm 1 Setpoint 1 Type Input Board Type Auto Cycle Operation Auto Cycling ConfigurationAccessing Auto Cycle Menu Auto Cycle 1 or Auto Cycle Offdefault Auto Cycling Configuration 16 Auto Cycling Configuration To 100default = To 28 default =Default = Sunday To 31 default = To 59 default = Enable PH Auto Cycling Configuration Example17 Example Auto Cycling Configuration for pH Selection Setting Resume Dly Mins Resume Dly Mins Analog Variables ConfigurationAccessing Variables Menu 18 Variables Configuration 19 Communication Configuration 17Communication ConfigurationAccessing Communication Menu Status display Ethernet 20 Maintenance Configuration Maintenance ConfigurationAccessing Maintenance Menu Option ID Number Loops defaultNo default Unit Identification ISO/NIST factor Nist defaultAWG default Feet default Default UDA2182 Default Honeywell Tag Names Hour defaultAM default Off default Output action occurs when the Enter key is Inputs and Outputs Wiring Immunity compliance References Recommended maximum wire size Recommended Maximum Wire SizeShielded wiring for locations with interference Avoiding interference Inputs and Outputs Accessing the terminals Wiring Terminals and board Location Procedure Wiring terminals and board location Procedure for installing Input and Output wiring Durafet Direct pH/ORP Input Wiring Diagrams Durafet Terminal Designations for Meredian II Electrode Glass Meredian ORP Terminal Designations for HPW7000 System HPW7000 Terminal Designations for HB Series pH or ORP HB Series pH or ORP Black Glass Meredian External Preamp1Blue Green + 10 Volt Supply RTH 3rd WireDurafet II External Preamp Durafet II Cap Adapter Durafet III Cap Adapter Brown Blue Conductivity Ground screw Dissolved Oxygen Yellow Wire to chassisCable shield Violet To chassis ground screw Clear RJ45 Ethernet Connection RS 485 Connection Communications Card Outputs Power Supply/Analog Output/Relay Output Card 20 Terminal Designations for Option Board Option Card Input Calibration Input PV Cal Input Temp Cal Output Cal Cal History Accessing the Main Calibration Menu and sub-menusCalibration Menu Conductivity PH/ORP and Conductivity OverviewPH/ORP Calibration Selection and care of electrode system or cell essential Recommendations for Successful Measurement and Calibration PH Calibration Using the restart screen Calibrating pH Electrodes Using Automatic Buffer recognition Standard pH Buffer Values Calibration functions Use To select Input PV Cal Enter NIST/USP defaultStep Action Screen Press Place probe in Buffer Press Enter when stableStep Action Screen Press Enter Auto Buffer Cal Buffer 2 stability check Buffering Method of Calibrating pH Electrodes Buffer Cal Procedure for Buffering Method of Calibrating pH ElectrodesStep Action Screen Press Input PV Cal Enter Press Enter when stable Sample Method of Calibrating pH Electrodes Procedure for Sample Method of Calibrating pH Electrodes Change to Sample Value Sample CalPlace probe in Sample Special instructions for high-purity water applications Resetting pH Offset and pH Slope ORP Calibration ORP Calibration Using Reference Solution Procedure This will standardize the unit Procedure for Calibrating ORP Analyzer Using Voltage Input ORP Calibration Using Voltage Input Press Sample Cal ORP Offset Viewing and Resetting ORP OffsetReset ORP Offset Entering the Cal Factor for each cell Introduction Conductivity Calibration Out-of range-values forced to closest limit Determining TDS conversion factor Performing Calibration Trim Introduction Concentration M Conductivity microSiemens Per cm Conductivity of Potassium Chloride Solutions at 25 C Error Messages Sample Cal Cal Trim1.00 Resetting Calibration Trim Cation pH 10 Procedure for Sample Method of Calibrating Cation pHCation pH Calibration Input PV Cal Enter Press Enter = recal, Exit = exit Cal CompleteTo recalibrate, press Enter Sample Cal PH Offset0.00 Resetting pH Offset Do’s and Don’ts for Dissolved Oxygen Calibration Dissolved Oxygen Calibration Air Cal Use To select Input 1 or 2 do Cal Enter Wait for cal complete Press Enter when readyEnter Place probe in air Enter Cal stability check January UDA2182 Universal Dual Analyzer Product Manual 169 Enter Place probe in sample Enter to save when the valueExit to cancel Pressure Cal Calibrating the Integral Pressure Sensor Introduction13 Calibrating the Integral Pressure Sensor Pressure Sensor Cal Running a Probe Bias Scan IntroductionTest initiation Interpretation of figure shown above is as follows Display Graph55V 80μA 240 160 ΜA 00 0.2 0.4 0.6 0.8 Procedure 14 Running a Probe Bias Scan January UDA2182 Universal Dual Analyzer Product Manual 175 176 IN1 do CAL Resetting Pressure Offset or Bias Volts Outputs Calibration Required equipment Output Calibration 180 Procedure Procedure for Calibrating Analyzer Outputs Use To select An Analog Output to be Calibrated Enter Case Step Action Screen Use To selectMA Offset and repeat Process Resetting Output 1 Offsets example Viewing and resetting 20mA and 4mA Offset 10.1Overview Temperature Input Calibration Input Temp Cal Enter Temperature Input CalibrationProcedure Procedure for Calibrating the Temperature Inputs Limit is ± 5ºC ± 9ºF Resetting temperature offset Viewing and resetting Temperature Offset Calibration Records Cal History items Calibration History Overview Clear Calibration History 12.1Overview Diagnostics and Messages = 1 or Measurement ErrorsSystem Status Messages Status Messages PH/ORP/DO Calibration DiagnosticsProbe Calibration Diagnostics Fail Message Reason Auto Cycle Fail MessagesAuto Cycle Fail Messages Status Condition 12.5Pharma Fail MessagesPharma Fail Messages Fail Condition 13.1Overview Ethernet and Communications 14.1Overview Accessories and Replacement Parts List Kit/Part Number Description Quantity Part NumbersPart Numbers Appendices Table of Contents Example of a Conductivity Loop January UDA2182 Universal Dual Analyzer Product Manual 201 Ft of 18 AWG coax January UDA2182 Universal Dual Analyzer Product Manual 203 Technique for cyanide destruction Uses of cyanide solutionsAppendix C Cyanide Waste Treatment Titration curve First Stage of Cyanide DestructionRaise pH and oxidize cyanide Neutralize and further oxidize cyanate Importance of pH controlReliable measurement with gold electrode Second Stage of Cyanide Destruction ORP Potential a Measure of Status of Reaction Batch Treatment Necessity for removal of chromium ion from wastewater 15.5Appendix D Chrome Waste TreatmentUse of Chromates Corrosion inhibition Lower pH and add reducing agent First Stage of Chrome Removal ORP Potential a Measure of Status Second Stage of Chrome Removal January UDA2182 Universal Dual Analyzer Product Manual 211 Conductivity/Resistivity/TDS Difference Appendix E Two-cell ApplicationsIon Exchange Reverse Osmosis Parts Rinsing Softener Monitor Steam Power Measurements January UDA2182 Universal Dual Analyzer Product Manual 215 Calculations for conductivity, resistivity, and TDS Set cal factor and calibration trim for ideal conditions Data for Concentration Range Measurements Concentration values Hints for Reducing Noise 15.8Appendix G Noise Testing, Dissolved Oxygen Application Check for probe membrane leakage 15.9Appendix H do Probe and Analyzer Tests Check that analyzer is working January UDA2182 Universal Dual Analyzer Product Manual 221 Salinity TemperaturePressure Charging Currents Faradaic CurrentsResidual Currents Electrode Conditioning Currents Faradaic Interferences Sulfite Based Zero Testing 15.12Appendix K Percent Saturation Readout Dissolved Oxygen Solubility vs. Temperature 15.13Appendix L Leak Detection in PPB Applications Equipment Needed Oxygen Measurement Procedure Example Calculation To Calculate True Value Typical Probe Installation 230 Automatic Cleaning and Calibration 15.16Appendix O Auto Clean and Auto Cal Examples Auto Clean Setup Automatic Calibration of ppb Dissolved Oxygen Probe 10 Auto Cal Setup AutoClean Sequence and Piping Appendix P AutoClean and AutoCal Theory and Piping AutoCal Sequence and Piping 11 Automatic Electrode Wash Setup 12 Rinse and One-Point Calibration Two-Point AutoCal Operation 238 Index Conductivity Conductivity Calibration January UDA2182 Universal Dual Analyzer Product Manual 241 Power Supply/Analog Output/Relay Output Card...132 Y, Z 244 January UDA2182 Universal Dual Analyzer Product Manual 245 Asia Pacific