Honeywell UDA2182 manual Out 2 Fault

		Configuration
Out 1 Fault	Output 1 Fault	Output open conditions. This allows an alarm to be triggered if the
		respective 4-20 mA output opens.
Out 2 Fault	Output 2 Fault
Out 3 Fault	Output 3 Fault
Hold	Hold	Engages Hold of Analog Inputs
Pharm 1 Warn	Pharmacopoeia 1	The Pharma 1 Display ( Section 5.8) outputs digital Warning signal
	Warning	whenever the measured conductivity exceeds the Percent Warning
		Value selected in the “Pharma Op Panel” on the Pharma Display
		(Stage 1only)
Pharm 1 Fail	Pharmacopoeia 1	The Pharma 1 Display ( Section 5.8) outputs digital Failure signal
	Failure	whenever one of the following conditions occur:
		Stage 1 – Measured Conductivity exceeds 100%
		Stage 1 – Temperature not within range of 0-100 degrees C
		Stage 2 – Conductivity is 0.1 µS/cm or greater for 5 minutes
		Stage 3 – pH not within range of 5 – 7pH
		Stage 2 and 3 – Temperature not within range of 24 – 26 degrees C.
Pharm 2 Warn	Pharmacopoeia 2	The Pharma 2 Display ( Section 5.8) outputs digital Warning signal
	Warning	whenever the measured conductivity exceeds the Percent Warning
		Value selected in the “Pharma Op Panel” on the Pharma Display
		(Stage 1only)
Pharm 2 Fail	Pharmacopoeia 2	The Pharma 2 Display ( Section 5.8) outputs digital Failure signal
	Failure	whenever one of the following conditions occur:
		Stage 1 – Measured Conductivity exceeds 100%
		Stage 1 – Temperature not within range of 0-100 degrees C
		Stage 2 – Conductivity is 0.1 µS/cm or greater for 5 minutes
		Stage 3 – pH not within range of 5 – 7pH
		Stage 2 and 3 – Temperature not within range of 24 – 26 degrees C.
PID 1 Alm 1	PID Control 1 Alarm 1	Control Alarms – See Table 6-15 PID Alarms
PID 1 Alm 2	PID Control 1 Alarm 2
PID 2 Alm 1	PID Control 2 Alarm 1
PID 2 Alm 2	PID Control 2 Alarm 2
AC 1 Extract	Auto Cycle 1 Probe	Auto Cycle 1 digital output (Cycle Start Source) configuration selection
	Extraction	See Table 6-16 Auto Cycling Configuration.
AC 1 Rinse	Auto Cycle 1 Probe	Auto Cycle 1 digital output (Cycle Start Source) configuration selection
	Rinse	See Table 6-16 Auto Cycling Configuration.
AC1 Cal	Auto Cycle 1	Auto Cycle 1 digital output (Cycle Start Source) configuration selection
	Calibration Point 1	See Table 6-16 Auto Cycling Configuration.
AC 1 Cal 2	Auto Cycle 1	Auto Cycle 1 digital output (Cycle Start Source) configuration selection
	Calibration Point 2	See Table 6-16 Auto Cycling Configuration.
AC 1 Fail	Auto Cycle 1 Failure	Auto Cycle 1 Failure is active whenever an Auto Cycle 1 failure occurs
		Auto Cycle 1digital output (Cycle Start Source) configuration selection
		See Table 6-16 Auto Cycling Configuration.
AC 2 Extract	Auto Cycle 2 Probe	Auto Cycle 2 digital output (Cycle Start Source) configuration selection
	Extraction	See Table 6-16 Auto Cycling Configuration.
AC 2 Rinse	Auto Cycle 2 Probe	Auto Cycle 2 digital output (Cycle Start Source) configuration selection
	Rinse	See Table 6-16 Auto Cycling Configuration.
AC 2 Cal	Auto Cycle 2	Auto Cycle 2 digital output (Cycle Start Source) configuration selection
	Calibration Point 1	See Table 6-16 Auto Cycling Configuration.

January 2009 UDA2182 Universal Dual Analyzer Product Manual 61