Changing Parameters on the PID Display | Honeywell UDA2182 guide

Operating the Analyzer

Changing Parameters on the PID Display

When either PID Display is on the Display screen, you can edit the Setpoint value, Setpoint Source, Control Mode, and the Output value. You can also enable or disable Accutune and Tune Set.

Table 5-3 Changing PID Parameters on the Display

Press				Action
Enter	to access the PID Parameters. You will see:

				PID LOOP 1

		LSP		0.00
		SP Source		Local SP
		Mode		Manual
		Output		0.00
		Tune Set 2		Disable

Example – PID Loop 1 Edit Display

to highlight the parameter you want to change.

Enter

to access the value or selection of each.

to change the value or selection.

Note: Output can only be changed in Manual mode.

Refer to “Section 6.4.1 – ”General Rules for Editing”.

Enter	to make the edit permanent.

Display	to return to the selected PID Display.

January 2009

UDA2182 Universal Dual Analyzer Product Manual

27

Image 39

Honeywell UDA2182 manual Changing Parameters on the PID Display, Changing PID Parameters on the Display, Press Action

Contents

January UDA2182 Universal Dual Analyzer Product Manual Copyright 2008 by Honeywell Revision January WARRANTY/REMEDY Telephone AbstractContacts World Wide Web Symbol Definition Symbol Definitions Contents 100 136 114 191 178185 189 239 Tables Figures Resetting ORP Offset Overview Introduction Communications Card Optional OutputsRelays Infrared Communications Features High Noise Immunity Password protectionAuto Clean/Auto Cal Diagnostic/Failsafe Outputs Specifications SpecificationsUDA2182 Universal Dual Analyzer Resistive Load Rating 4A, 120/240 Vac Declaration of Conformity CE Conformity Europe Specifications Unpacking, Preparation, and Mounting IntroductionWhat’s in this section? Step Action Procedure Procedure for Unpacking and Preparing the UDA2182Unpacking and Preparing Mounting Panel Cutout Panel Mounting Dimensions Rear Panel Support Plate Dimensions Pipe Mounting Pipe Mounting Dimensions not to scale Wall Mounting Dimensions not to scale Wall Mounting Dimensions Power Wiring Avoid damage to components General Wiring PracticesSafety precaution Wiring for immunity compliance Installing Power Wiring Power Wiring Considerations Disengage from the terminal boards Power Wiring Operating the Analyzer UDA2182 Operator Interface all display items shown Analyzer Overview Function Key NavigationFunction of Keys Key Displays Overview Status Messages Online Functions Display Details FunctionsProcess Variable Values Two Input Display Input Displays PID Displays OverviewSelecting Control Display Changing PID Parameters on the Display To access the PID Parameters. You will seeTo access the value or selection of each Changing Parameters on the PID Display Auto Cycle Displays Access to Auto Cycle Displays Displays How it works Cycle Interval Hold ActiveProbe Transit Cycle Start Src To access the Auto Cycle Operator Panel. You will see Manual Starting/Stopping the Auto CycleManually Starting/Stopping the Auto Cycle Condition Output Hold State EnabledAuto Cycle Fail Step AC n Extract Rinse Cal Pharma Display Pharmacopoeia Test Procedure Pharma Display screen example Displays Access to Pharma Display Selecting the Pharma Test on Display To select Test µS/cm After Stage 2 is selectedTo select Test pH After Stage 3 is selected Pharma Warning and Fail Signal UDA for Cation and Degassed CO2 How it works Cation Calc Display Degassed CO2 PH Calculation from Specific and Cation Conductivity Setup Access to Cation Display Calibration5 CO2 by Degassed Conductivity Check pH Electrode System Troubleshooting Status Display Details Access to Status DisplaysPID Alarm 10Status Display Relay States Input StatusOutput Levels Comm Status Output of the Switch and Function Generator blocksAux Values Variables Auto Cycling ConfiguredStatus Parameter Status Definition Display Read Only MACaddr Hi and MACaddr Low is the MAC address Available only if both units of measure between Press Until you see Access to Event History DisplaysSetup Chg 04.19 Alarm 1 On 03.15 Hold On Power On 03.09 Event History Clear Event History 12Process Instrument Explorer Software Features Infrared communications Ethernet port provides Modbus CommunicationsSummary Serial port provides Configuration UDA2182 Block Diagram UDA2182 Block Diagram Main Setup Menu Accessing the Main MenuSetup Group Overview Configuration General Rules for Editing Basic Configuration Procedure Enter Basic Configuration Procedure Exit Analog and Digital Signal Sources Signal SourcesSignal Type Applies Source to Selections Analog Signal Description Definition Analog Signal Sources Digital Signal Description Definition Digital Signal Sources Out 2 Fault DgtlVar Inputs Configuration Accessing Inputs MenuInput Configuration Default = Default = 77ºFDefault = 25ºC None default Sub-menu Parameter Following important differences8550 Ω Therm Default to Cell Const Cell Const 0 Cond mS/m NIST-default +ISO-Default + Cond Only PV Type 000default Selection Range Setting H2SO4 NaCl default Configured minutes value set here. When the Timer Default = NoneDefault 10.000 Pharma Timer begins to count down from Manual Input Do ConcenOxygen do concentration or percent saturation 5000Ω Therm Default = 20.000 Outputs Configuration Accessing Outputs MenuOutputs Configuration Parameters in % Parameters in engineering units Accessing Relays Menu Relays Configuration Overview Relays Configuration Frequency ON/OFF Pulse Output Range Switch using Math, Monitor, and Switch Blocks Alarms Configuration Accessing Alarms Menu Alarms ConfigurationHigh default 10Monitors Configuration Accessing Monitors MenuMonitors Configuration For Low Monitor Accessing Math Menu 11Math Configuration Linear default 10 Math Configuration Accessing Logic Menu Logic Configuration Latch 11 Logic Configuration Auxiliary Configuration SwitchFunc Gen Function Generator Accessing Auxiliary Menu 12 Auxiliary ConfigurationSub-menu Parameter Selection or Range of Setting 99999 to 999999 Default= PID Tracking PID Control ConfigurationPID Tracking versus Manual Mode Using Auto/Manual Switch Configuration 13 PID Configuration Accessing Control MenuPIDn Config Table PIDnAlarms Table Failsafe default Pida defaultReverse default Manualdefault 9999 to Enable default PID 2 Tune Disable default 14 PID Tuning 15 PID Alarms No Alarm defaultPID 2 Alarms Setpoint No Alarm default Same as Alarm 1 Setpoint 1 Type Input Board Type Auto Cycle Operation Auto Cycling ConfigurationAccessing Auto Cycle Menu Auto Cycle 1 or Auto Cycle Offdefault Auto Cycling Configuration 16 Auto Cycling Configuration To 100default = To 28 default =Default = Sunday To 31 default = To 59 default = Enable PH Auto Cycling Configuration Example17 Example Auto Cycling Configuration for pH Selection Setting Resume Dly Mins Resume Dly Mins Analog Variables ConfigurationAccessing Variables Menu 18 Variables Configuration 17Communication Configuration Accessing Communication Menu19 Communication Configuration Status display Ethernet Maintenance Configuration Accessing Maintenance Menu20 Maintenance Configuration Option ID Number Loops defaultNo default Unit Identification ISO/NIST factor Nist defaultAWG default Feet default Default UDA2182 Default Honeywell Tag Names Hour defaultAM default Off default Output action occurs when the Enter key is Inputs and Outputs Wiring Immunity compliance References Recommended maximum wire size Recommended Maximum Wire SizeShielded wiring for locations with interference Avoiding interference Inputs and Outputs Accessing the terminals Wiring Terminals and board Location Procedure Wiring terminals and board location Procedure for installing Input and Output wiring Durafet Direct pH/ORP Input Wiring Diagrams Durafet Terminal Designations for Meredian II Electrode Glass Meredian ORP Terminal Designations for HPW7000 System HPW7000 Terminal Designations for HB Series pH or ORP HB Series pH or ORP Black Glass Meredian External Preamp1Blue Green RTH 3rd Wire Durafet II External Preamp+ 10 Volt Supply Durafet II Cap Adapter Durafet III Cap Adapter Brown Blue Conductivity Ground screw Dissolved Oxygen Yellow Wire to chassisCable shield Violet To chassis ground screw Clear RJ45 Ethernet Connection RS 485 Connection Communications Card Outputs Power Supply/Analog Output/Relay Output Card 20 Terminal Designations for Option Board Option Card Input Calibration Accessing the Main Calibration Menu and sub-menus Calibration MenuInput PV Cal Input Temp Cal Output Cal Cal History PH/ORP and Conductivity Overview PH/ORP CalibrationConductivity Selection and care of electrode system or cell essential Recommendations for Successful Measurement and Calibration PH Calibration Using the restart screen Calibrating pH Electrodes Using Automatic Buffer recognition Standard pH Buffer Values Calibration functions Use To select Input PV Cal Enter NIST/USP defaultStep Action Screen Press Place probe in Buffer Press Enter when stableStep Action Screen Press Enter Auto Buffer Cal Buffer 2 stability check Buffering Method of Calibrating pH Electrodes Buffer Cal Procedure for Buffering Method of Calibrating pH ElectrodesStep Action Screen Press Input PV Cal Enter Press Enter when stable Sample Method of Calibrating pH Electrodes Procedure for Sample Method of Calibrating pH Electrodes Change to Sample Value Sample CalPlace probe in Sample Special instructions for high-purity water applications Resetting pH Offset and pH Slope ORP Calibration ORP Calibration Using Reference Solution Procedure This will standardize the unit Procedure for Calibrating ORP Analyzer Using Voltage Input ORP Calibration Using Voltage Input Press Viewing and Resetting ORP Offset Reset ORP OffsetSample Cal ORP Offset Entering the Cal Factor for each cell Introduction Conductivity Calibration Out-of range-values forced to closest limit Determining TDS conversion factor Performing Calibration Trim Introduction Concentration M Conductivity microSiemens Per cm Conductivity of Potassium Chloride Solutions at 25 C Error Messages Sample Cal Cal Trim1.00 Resetting Calibration Trim Cation pH 10 Procedure for Sample Method of Calibrating Cation pHCation pH Calibration Input PV Cal Enter Press Cal Complete To recalibrate, press EnterEnter = recal, Exit = exit Sample Cal PH Offset0.00 Resetting pH Offset Do’s and Don’ts for Dissolved Oxygen Calibration Dissolved Oxygen Calibration Air Cal Use To select Input 1 or 2 do Cal Enter Wait for cal complete Press Enter when readyEnter Place probe in air Enter Cal stability check January UDA2182 Universal Dual Analyzer Product Manual 169 Enter to save when the value Exit to cancelEnter Place probe in sample Calibrating the Integral Pressure Sensor Introduction 13 Calibrating the Integral Pressure SensorPressure Cal Running a Probe Bias Scan Introduction Test initiationPressure Sensor Cal Display Graph 55V 80μA 240 160 ΜA 00 0.2 0.4 0.6 0.8Interpretation of figure shown above is as follows Procedure 14 Running a Probe Bias Scan January UDA2182 Universal Dual Analyzer Product Manual 175 176 IN1 do CAL Resetting Pressure Offset or Bias Volts Outputs Calibration Required equipment Output Calibration 180 Procedure Procedure for Calibrating Analyzer Outputs Use To select An Analog Output to be Calibrated Enter Case Step Action Screen Use To selectMA Offset and repeat Process Resetting Output 1 Offsets example Viewing and resetting 20mA and 4mA Offset 10.1Overview Temperature Input Calibration Temperature Input Calibration Procedure Procedure for Calibrating the Temperature InputsInput Temp Cal Enter Limit is ± 5ºC ± 9ºF Resetting temperature offset Viewing and resetting Temperature Offset Calibration Records Cal History items Calibration History Overview Clear Calibration History 12.1Overview Diagnostics and Messages = 1 or Measurement ErrorsSystem Status Messages Status Messages Calibration Diagnostics Probe Calibration DiagnosticsPH/ORP/DO Auto Cycle Fail Messages Auto Cycle Fail MessagesFail Message Reason Status Condition 12.5Pharma Fail MessagesPharma Fail Messages Fail Condition 13.1Overview Ethernet and Communications 14.1Overview Accessories and Replacement Parts List Part Numbers Part NumbersKit/Part Number Description Quantity Appendices Table of Contents Example of a Conductivity Loop January UDA2182 Universal Dual Analyzer Product Manual 201 Ft of 18 AWG coax January UDA2182 Universal Dual Analyzer Product Manual 203 Uses of cyanide solutions Appendix C Cyanide Waste TreatmentTechnique for cyanide destruction First Stage of Cyanide Destruction Raise pH and oxidize cyanideTitration curve Neutralize and further oxidize cyanate Importance of pH controlReliable measurement with gold electrode Second Stage of Cyanide Destruction ORP Potential a Measure of Status of Reaction Batch Treatment Necessity for removal of chromium ion from wastewater 15.5Appendix D Chrome Waste TreatmentUse of Chromates Corrosion inhibition Lower pH and add reducing agent First Stage of Chrome Removal ORP Potential a Measure of Status Second Stage of Chrome Removal January UDA2182 Universal Dual Analyzer Product Manual 211 Conductivity/Resistivity/TDS Difference Appendix E Two-cell ApplicationsIon Exchange Reverse Osmosis Parts Rinsing Softener Monitor Steam Power Measurements January UDA2182 Universal Dual Analyzer Product Manual 215 Calculations for conductivity, resistivity, and TDS Set cal factor and calibration trim for ideal conditions Data for Concentration Range Measurements Concentration values Hints for Reducing Noise 15.8Appendix G Noise Testing, Dissolved Oxygen Application Check for probe membrane leakage 15.9Appendix H do Probe and Analyzer Tests Check that analyzer is working January UDA2182 Universal Dual Analyzer Product Manual 221 Temperature PressureSalinity Charging Currents Faradaic CurrentsResidual Currents Electrode Conditioning Currents Faradaic Interferences Sulfite Based Zero Testing 15.12Appendix K Percent Saturation Readout Dissolved Oxygen Solubility vs. Temperature 15.13Appendix L Leak Detection in PPB Applications Equipment Needed Oxygen Measurement Procedure Example Calculation To Calculate True Value Typical Probe Installation 230 Automatic Cleaning and Calibration 15.16Appendix O Auto Clean and Auto Cal Examples Auto Clean Setup Automatic Calibration of ppb Dissolved Oxygen Probe 10 Auto Cal Setup AutoClean Sequence and Piping Appendix P AutoClean and AutoCal Theory and Piping AutoCal Sequence and Piping 11 Automatic Electrode Wash Setup 12 Rinse and One-Point Calibration Two-Point AutoCal Operation 238 Index Conductivity Conductivity Calibration January UDA2182 Universal Dual Analyzer Product Manual 241 Power Supply/Analog Output/Relay Output Card...132 Y, Z 244 January UDA2182 Universal Dual Analyzer Product Manual 245 Asia Pacific