Honeywell UDA2182 manual Resistive Load Rating 4A, 120/240 Vac

Specifications

	UDA2182 Universal Dual Analyzer
Control Loop/Outputs	Control Loops: 2 standard (one for each PV); current, pulse frequency, or time proportional
	Control Loop Types: PID (optional), Duplex (optional), On/Off (standard)
	Auto-tuning:Accutune II, fuzzy logic overshoot suppression, applicable to both PID loops
Standard Alarm/ Control	Two SPDT (Form “C”) Relays
Relays	Resistive Load Rating: 4A, 120/240 Vac
Optional Additional	Two SPDT (Form “C”) Relays
Alarm/Control Relays	Resistive Load Rating: 4A, 120/240 Vac
Alarm/Control Settings	Alarm/on-off control delay: 0-100 seconds.
	Alarm/on-off control deadbands: individually set, from 1 count to full scale for pH, ORP, and
	temperature.
	On/off cycle period: 0 to 1000 seconds.
	On/off percent “on” time: 0 to 100%, 1% resolution.
	Set point and proportional band limit ranges: ±19.99 pH, ±1999 mV, -10 to 130°C, 1 count resolution.
	DAT cycle period: 1 to 1999 seconds.
	PFT maximum frequency: 1 to 200 pulses/minute.
	PFT pulse width: 50 ms, compatible with electronic pulse-type metering pumps.
Remote Preamplifier Input	Optional input card to accept input signal from Honeywell digital preamplifiers:
Option	Meridian II – 31075707 and 31022283
	Durafet – 31079288 and Cap Adapter cables
pH Temperature	Conventional compensation for changing electrode output (Nernst response), plus selectable solution
Compensation	temperature compensation for high-purity water.
Calculated pH from	User selectable when unit has two Conductivity inputs. Used when ammonia or amine is the water
Differential Conductivity	treatment chemical.
Auto Buffer Recognition	User Selectable
(pH)	Available Buffer Series: NIST/USP, US, and Euro
Conductivity	NaCl, HCl, H2SO4, PO4, NaOH, NH3, C4H9C, Pure Water, Custom (User Selectable)
Compensations
Dissolved Oxygen	Max flowrate (probe): 950 ml/min with flow chamber; no dependence on stirring or flowrate
Measurement	Atmospheric pressure: 500-800 mm Hg with internal sensor, for calibration
	Calibration with either Air or Sample
Auto Clean/ Auto Cal	Real time clock is used to set-up cycles to initiate a cleaning and calibration sequence. Cycle Set-up is
Function	user configurable.
Event History Screen	Event history screen stores 256 events with a description of the event and a Date/time stamp.
Calibration History Screen	Calibration history screen stores information on 128 calibration events with a date/time stamp.
Power Requirements	90 -264 Vac, 47-63 Hz, 15 VA. Memory retained by E2PROM when power is off.
Wireless Interface	Type: Infrared (IR)
	Length of Link: 0 –1 M, 0 –15° Offset
	Baud Rate: 9600
	Data Format: Modbus Protocol
RS422/RS485 Modbus	Baud Rate: 2400, 4800, 9600, 19200, 38400, 57600, or 115200 selectable
RTU Slave	Data Format:: IEEE floating point and 32-bit integer. Word swap configurable.
Communications Interface	Length of Link:
(Optional)	2000 ft (600 m) max. with Belden 9271 Twinax Cable and 120 ohm termination resistors
	4000 ft (1200 m) max. with Belden 8227 Twinax Cable and 100 ohm termination resistors
	Link Characteristics: Two-wire (half-duplex), multi-drop Modbus RTU protocol, 15 drops maximum or
	up to 31 drops for shorter link length.
	Modbus RTU slave: Provides monitoring of inputs outputs, statuses, alarms, and variables. Provides
	writing of variables for remotely modifying parameter settings.

6 UDA2182 Universal Dual Analyzer Product Manual January 2009