Honeywell UDA2182 manual Power Supply/Analog Output/Relay Output Card...132

Index

PID Alarms	97
PID B	94
PID Configuration	93
PID Control	107
PID Control 1 Alarm 1	60
PID Control 1 Alarm 2	60
PID Control 2 Alarm 1	60
PID Control 2 Alarm 2	60
PID Control Configuration	91
PID Display Editing	27
PID Displays	26
PID Tuning	96
Pipe Mounting	13
Power Mode	94
Power Out	94
Power Requirements	6
Power Supply/Analog Output/Relay Output Card...132
Power Wiring	15
Power Wiring Considerations	17
Preamplifier Input Option	6
Precision Check Resistor	196, 213
Pressure Calibration	163
Pressure Calibration Method	168
Pressure Type	71
Probe Bias Scan	171
Probe Calibration Diagnostics	190
Probe Current Too High	190
Probe Current Too Low	191
Probe Current Too Low	190
Probe Extract Timeout	191
Probe Insert Timeout	191
Probe Pv N Fault	189
Probe Temp N Fault	189
Probe Transit	30
Procedure for Calibrating Analyzer Outputs	178

Procedure for Calibrating the Temperature Inputs 183,

186
Process Instrument Explorer Software	.....................47
Process Variable Source	81, 93
Process Variable Values	24
Proportional (P)	91
Proportional Band (PB)	96
PTS OVERRANGE	190
PTS UNDERRANGE	190
Pulse Output	75, 76, 79
PV Bias	70
PV High	93, 100, 102
PV Low	93, 100, 102
PV n INPUT OPEN	189
PV n OVERRANGE	189
PV n UNDERRANGE	189
PV Source	76, 77
PV Temperature	24
PV Type	62, 64, 67, 70

R
Range High	73
Range Low	73
Rate 2	97
RATE action	96
Ratio	94
Readings Unstable	191
READINGS UNSTABLE	190
Rear Panel Support Plate Dimensions	12
Recommended wire size	17
Relay outputs	117
Relay state	111
Relay States	42
Relay Types	76
Relays	2
Relays Configuration	75
Remote Setpoint Permit	95
Remote Setpoint Select	95
Remote Setpoint Source	94
Repeat per minute	96
Replacement Parts List	194
RESET (Integral Time)	97
Reset 2	97
Resetting Calibration Trim	159
Resetting ORP Offset	153
Resetting Output 1 Offsets	181
Resetting pH Offset	162
Resetting pH Offset and (Standardization) pH Slope
...........................................................................	147
Resetting Pressure Offset or Bias Volts	174
Resetting temperature offset	185
resume delay	102
Resume Dly Mins	30
Rinse Cycle Cnt	30
Rinse Mins	30
RS422/RS485 Modbus RTU Slave Communications
Interface	6
S
Safety Compliance	7
Safety precaution	16, 113
Salinity ppt	71
Salinity Type	71
Sample Calibration	163
Sample Calibration Method	166
Sample Method of Calibrating pH Electrodes	145
Sample Method of Calibrating Cation pH	160
Sample Tap Electrode Mounting Recommendations
...........................................................................	226
Saturation	70
Sequencer Steps for Auto Cycle	32, 35
Serial port	49
Setpoint at Power up	94
Setpoint High Limit Value	93
Setpoint Low Limit Value	93
Setpoint Value	81
Setup Group Overview	52
Shielded wiring for locations with interference	114
Signal Sources	57
Single Displays	25
Slew Time	73

242 UDA2182 Universal Dual Analyzer Product Manual January 2009