TP-6200 10/12 105Section 2 Operation
Local Programming Mode On
Menu 10—Output Setup
Menu 10 Displays with Key Entries
Key
Entry Display Description

Input a menu number.

MENU 10
OUTPUT SETUP

Displays the common faults heading.

DEFINE COMMON →
FAULTS
SYSTEM EVENTS →Displays the system events heading.
COMMON FAULT Y/N
(see Group B)

Gives the user the option to add or delete the selection from the

defined system events group. Press the Menu Down key to continue

to the next selection (repeat as necessary).

OR

COMMON FAULT YES
(see Group B)
COMMON FAULT YES
(see Group B)
COMMON FAULT NO
(see Group B)
COMMON FAULT NO
(see Group B)
Press the Enter key.
Confirms the entry.
Press the Enter key.
Confirms the entry.
GroupB
For defined system events,
choose from the following 66
status events and faults by
changing selection to YES.See
Appendix E for application and
restrictions with specific
engines.
EMERGENCY STOP
OVER SPEED
OVER CRANK
HI COOL TEMP SHUTDWN
OIL PRESS SHUTDOWN
LOW COOLANT TEMP
(non-ECM engines)
LOW FUEL
HI COOL TEMP WARNING
OIL PRES WARNING
MASTER NOT IN AUTO
NFPA 110 F AULT (se e
Menu 10 introduction for list)
LOW BATTERYVOLTAGE
HIGH BATTERYVOLTAGE
BATTERYCHARGE FAULT
SYSTEM READY
LOSS OF ECM COMM
(ECM
engines)
GroupB, continued
NO OIL PRESS SIGNAL
HI OIL TEMP
NO COOL TEMP SIGNAL
LOW COOLANT LEVEL
SPEED SENSOR FAULT
LOCKED ROTOR
MASTER SWITCH ERROR
MASTER SWITCH OPEN
MASTER SWITCH TO OFF
AC SENSING LOSS
OVER VOLTAGE
UNDER VOLTAGE
WEAK BATTERY
OVER FREQUENCY
UNDER FREQUENCY
LOAD SHED KW OVER
LOAD SHED UNDER FREQ
OVER CURRENT
EPS SUPPLYINGLOAD
INTERNAL FAULT
DELAYENG COOLDOWN
DELAYENG START
STARTINGAID
GENERATORSET RUNNING
MAIN MENU NUMBER 10
ENTER MENU NO. 1--15
Press the Enter key.

Displays the menu number and name.

GroupB, continued
AIR DAMPER CONTROL
GROUND FAULT
EEPROM WRITE FAILURE
CRITICAL OVERVOLTAGE
ALTERNATORPROTECTION
SHUTDOWN
AIR DAMPER INDICATOR
DEFINED COMMON FAULT
(RDO only) (see Menu 10
introduction for list)
SCRDOs 1--4
(software controlled RDOs)
MAINTENANCE DUE
ENGINE DERATEACTIVE
ENGINE STALLED(ECM engine)
J1939 CAN SHUTDOWN
(ECM engine)
Paralleling Applications only:
SD REVERSE POWER
SD OVER POWER
SD LOSS OF FIELD
SD OVERCURRENT PR
COMMON PR OUTPUT
IN SYNCH
BREAKER TRIP
COMMON FAULT NO
(see Group B) Entering YES adds the selection to the defined system event group.
COMMON FAULT YES
(see Group B)

Entering NO removes the selection from the defined system event

group.

GroupB, continued
Waukesha-Powered
models only:
FUEL VALVERELAY
PRELUBE RELAY
AFM REMOTE START
NO OIL TEMP SIGNAL
HI OIL TEMP WARNING
NO AIR TEMP SIGNAL
INTAKEAIR TEMP WARN
INTAKEAIR TEMP SDWN
AFM ENG STARTRELAY
DDC/MTU engine with
MDEC/ADEC only:
HI OIL TEMP WARNING
INTAKEAIR TEMP WARN
INTAKEAIR TEMP SDWN
ECM YELLOW ALARM
ECM RED ALARM
BLOCK HEATERCONTROL
LOW COOL TEMP SDOWN
LOAD SHED OVER TEMP