Kohler 20-3250 kW manual Avg L-L

Menu List Summary, continued (Legend: D First level submenu, d second level submenu)

Menu 10	Menu 10	Menu 11		Menu 12
Output Setup, cont.	Output Setup, cont.	Voltage Regulator		Calibration
Group B, continued	Group B, continued	AVG L-L V		Scale AC Analog
Low Battery Voltage	Reverse Power Shutdown[	Volt ADJ		Inputs
High Battery Voltage	Over Power Shutdown[	D	L1-L2 Volts	Generator Set Voltage LN
Battery Charger Fault	Loss of Field Shutdown[	D	L2-L3 Volts (3 phase)	D	Gen L1-L0 V
System Ready	Overcurrent VR Shutdown[	D L3-L1 Volts (3 phase)			Calibration Reference
				D	Gen L2-L0 V
Loss of ECM Comm	Common Protective Relay	Under Freq. Unload
		Enabled N/Y			Calibration Reference
(ECM engines)	Output[
				D	Gen L3-L0 V (3 phase)
No Oil Pressure Signal	In Synchronization[	D	Frequency
			Setpoint (Cut-In Point)		Calibration Reference
High Oil Temperature	Breaker Trip[
		D	Slope	Generator Set Voltage LL
Shutdown	Fuel Valve Relay*
			Volts-Per-Cycle	D	Gen L1-L2 V
No Temperature Signal	Prelube Relay*
		Reactive Droop			Calibration Reference
Low Coolant Level	Air/Fuel Module Remote
		Enabled N/Y		D	Gen L2-L3 V (3 phase)
Speed Sensor Fault	Start*
		D Voltage Droop at 0.8 PF			Calibration Reference
Locked Rotor	No Oil Temperature Signal*
			Rated Load	D	Gen L3-L1 V (3 phase)
Master Switch Error	High Oil Temperature
		VAR Control			Calibration Reference
Master Switch Open	Warning*]
		Enabled N/Y		D	Calibrate Regulator Y/N
Master Switch to Off	No Air Temperature Signal*
		D	Total kVAR (Running)	Generator Set Amps
AC Sensing Loss	Intake Air Temperature		kVAR Adj
				D	Gen L1 Amps
Over Voltage	Warning*]	D	Generating/Absorbing Y/N
					Calibration Reference
	Intake Air Temperature
Under Voltage
		PF Control		D	Gen L2 Amps
	Shutdown*]
		Enabled N/Y
Weak Battery					Calibration Reference
	Air/Fuel Module Engine
Over Frequency		D	Average PF	D	Gen L3 Amps (3 phase)
	Start Delay*
Under Frequency			PF Adjustment		Calibration Reference
	ECM Yellow Alarm]
Load Shed kW Over		D	Lagging/Leading Y/N	Load Voltage LN
	ECM Red Alarm]	Regulator Gain Adj.
Load Shed Under Freq				(Paralleling Applications
	Block Heater Control]	D
Over Current			Gain	only)
	Low Coolant Temperature
EPS Supplying Load		Utility Gain Adj.		D	Load L1--L0 V
	Shutdown]
Internal Fault		D	Gain		Calibration Reference
	Load Shed
		Analog Voltage Adjust		D	Load L3--L0 V
Delay Engine Cooldown
	Overtemperature]
		Enabled N/Y			Calibration Reference
Delay Engine Start
	Maintenance Due
		Reset Regulator Defaults?		Restore Defaults? Y/N
Starting Aid
	Engine Derate Active
Generator Set Running				Scale Aux. Analog
	Engine Stalled
				Inputs
Air Damper Control
	(ECM engines)
				D	Zero Aux. Analog
Ground Fault	J1939 CAN Shutdown
					Inputs?
EEPROM Write Failure	(ECM engines)
					(Scroll through up to 7
Critical Overvoltage
	*Waukesha engine				user-defined
Alternator Protection
	[Paralleling applications				descriptions. See
Air Damper Indicator	]DDC/MTU engine with				Figure 2-8 in User Inputs
Defined Common Fault	MDEC/ADEC				for factory-reserved
(RDO only)					inputs that are not user-
SCRDOs 1--4 (Software-					selectable.)
Controlled RDOs)				D	Analog 01
					Scale Value 1
					d Scale 1 V
					Scale 2 V
				D	Analog 01
					Scale Value 2
					d Scale 1 V
					Scale 2 V

TP-6200 10/12 Section 2 Operation 45