Managing System Parameters, Polling Interval | Cisco Systems 1105

Chapter 6 Performing Administrative Tasks

Managing System Parameters

Managing System Parameters

The System Parameters window allows you to set certain global parameters. For example, to change the interval at which the Wireless Clients reports will be updated, change the value of the Wireless Client Poll Interval parameter.

Note Your login determines whether you can use this option.

Procedure

Step 1 Select Administration > System Parameters. The following parameters are displayed in the System Parameters window:

Table 6-10 System Parameters

	Parameter	Description

	Inventory Poll Interval	Interval at which the configuration data will
		be collected from the devices. (This is the data
		shown in any GUI device detail table.)
		Tip	For more accurate trending, set this
			parameter at a lower interval than the
			Inventory Performance Attributes
			Polling Interval.
		Default: 1 hour

	Wireless Client Poll Interval	Interval at which the device data is collected
		for client information and at which the
		Wireless Clients reports are updated.
		Default: 5 minutes

	Inventory Performance Attributes Polling Interval	Interval at which the performance and
		utilization data will be collected from the
		devices.
		To set the aggregation period of this data,
		change the Aggregation Interval parameter.
		Default: 15 minutes

	User Guide for the CiscoWorks 1105 Wireless LAN Solution Engine

	78-14947-01				6-73

Image 379

Cisco Systems 1105 Managing System Parameters, Parameter Description, Inventory Performance Attributes, Polling Interval

Contents

Corporate Headquarters Copyright 2002, Cisco Systems, Inc All rights reserved Iii N T E N T S Setting Trap Notification Assigning an Auto-Managed Configuration Displaying an EAP Authentication Report Vii Displaying a Server Response Time Graph Viii Command History Feature B-3 Privilege Level 15 Commands B-17 Show ipchains show hosts B-61show maillog Show tech B-68 Xii Boldface font AudienceConventions Convention Xiv Related DocumentationOption Network Preferences Paper Documentation World Wide Web Obtaining DocumentationOnline Documentation Cisco documentation is available in these ways 800 553-NETS Obtaining Technical AssistanceOrdering Documentation Documentation Feedback Technical Assistance Center Cisco.comXvii Cisco TAC Escalation Center Cisco TAC Web SiteXviii Xix Page A P T E R Overview of the Wireless LAN Solution Engine Wlse Dashboard Understanding the Wlse User Interface Main Tab Subtabs Tabs and Subtabs Devices under management, run immediate inventories, view Administrative TasksButtons Performing Time Display Device Name and IP Address Display CiscoWorks 1105 Wireless LAN Solution Engine ProcedureLogging In and Out Task Description and References Getting Started with Device Management Managing Devices, page 6-2. After moving devices to Administering Users,Inventories, Settings, page 2-20 to set policies Displaying Faults Devices Severity FieldDescription State Name/IP Column Click Apply. The following table appears Related Topics Viewing Fault DetailsManaging Profiles, Notification Settings, Fault details for See Time Display, Family Product Type IfIndexConditions Description Column Description Managing Profiles Fault History Use this option to create a profile Creating a ProfileCopying a Profile Assigning a Profile to a Device, Viewing Devices, Use this option to edit a profile Renaming a ProfileEditing a Profile Use this option to rename a profile Assigning a Profile to a Device Deleting a ProfileUse this option to delete a profile Viewing Devices Specifying Security Policies Profile Choices Click Add to add the Ssid to the list, then go to Step Field Description Complete the following StepGo to Step Complete the following Setting Access Point Fault Thresholds Specifying Fault Thresholds Continue to Step Enable Poll Interval Settings Overloaded Degraded Setting Switch Fault Thresholds To set the new entries Go to step Step Setting Server Response Time Setting Router Fault Thresholds Notification Settings Before You Begin Setting Trap Notification Setting Syslog Notification, Emailing Faults, Setting Syslog Notification Attribute Description Emailing FaultsTo save your settings Setting Trap Notification, Emailing Faults, Procedure Setting Trap Notification, Setting Syslog Notification, Fault Monitoring Notification Settings Using the Templates Configuring Devices Related Topic Template ChoicesTemplate Categories Naming the Template Using Express TemplateSee Naming Guidelines, page A-1 Express Template Settings Configuring Devices Field Description LAN Finish to save the template. See Finishing the Template, Setting Up Association This option is used for only bridges Defining Spanning Tree Protocol Disable-If you do not want STP enabled Enable-Use this setting to enable STP onBridge Configuring Devices Defining Address Filters Field Description Defining Ethertype Filters Creating New Ethertype Filters Procedure Creating New Ethertype Filters Settings Creating Special Cases Procedure Deleting Ethertype Filters Procedure Configuring Devices Defining IP Protocol Filters Deleting Special Cases Procedure Creating New IP Protocol Filters Procedure Using this option you can also Deleting IP Protocol Filters Procedure IP Protocol Filters Special Cases Settings Field Description Defining IP Port Filters To create and enable port filters, enter the following Creating New Port Filters Procedure Deleting Port Filters Procedure IP Port Filters Special Cases Settings Configuring Devices Configuring Policy Groups IP Protocol Adding or Deleting a New Policy GroupTo add a new policy group, enter the following Filters Deleting an Existing Policy Group from a Device Protocol Filters Configuring VLANs Enter the following information Setting on the switchAdd a new VLAN-SeeAdding a New VLAN, Enter the identification number of the Vlan Created using Association Policy GroupsAdding a New Vlan To add a new VLAN, enter the following Field Description Vlan Deleting an Existing Vlan Procedure Configuring Quality of Service Quality of Service Settings This option allows you to define service sets Configuring Service Sets Association VLANs Add a new Service Set-SeeAdding a New Service Set,Adding a New Service Set Procedure Using Association Policy Groups Field Description Finish to save the template. See Finishing the Template, Defining Advanced Associations Deleting an Existing Service Set Procedure 10 Advanced Association Settings ExternalWarning-Indicates that an error or SystemWarning-Indicates that an error orProtocolWarning-Indicates that an error or PortWarning-Indicates that an error or failure Field Description Finish to save the template. See Finishing the Template, Lists the port’s 802.11 radio drivers association Configuring Port AssignmentsIdentifier Configuring Dscp to CoS Use this option to configure the device’s Ethernet port Configuring the Ethernet PortIdentifying the Ethernet Port Enter the following information to identify the port Setting Up Ethernet Filters Filters you created using Association IP Port Filters Filters you created using Association Ethertype Filters Setting Up Hardware Ssid Defining the Ethernet Advanced Settings Allowed under Association Address Filters Disallowed under Association Address Filters Set as disallowed under Association Address Use this option to configure the device’s 11b radio Configuring the 11b RadioIdentifying the 11b Radio Port Procedure Ethernet Identification , Primary Port? From the list, select one of the followingSelected value is displayed Association Ethertype Filters Setting Up 11b Radio FiltersAssociation IP Protocol Filters IP Port Receive Transmit Defining the 11b Radio Hardware Settings 18 11b Radio Hardware Settings Field Description Configuring Devices Field Description Field Description Defining the 11b Radio Advanced Settings Addresses set as allowed under Disallowed-The access point discardsAssociation Address Filters All traffic except packets sent to the MAC Field Description This setting is valid None-Does not enable MICNMH-Enables MIC Message Integrity Check, a security feature that protects Field Description Defining the 11b Radio Searched Channels Settings 20 11b Radio Searched Channels Settings Use this option to configure the device’s 11a radio Configuring the 11a RadioIdentifying the 11a Radio Port Ethernet Identification, Ethertype Receive Transmit Setting Up 11a Radio Filters Right pane Defining the 11a Radio Hardware Settings 23 11a Radio Hardware Settings 78-14947-01 Configuring Devices Field Description Defining the 11a Radio Advanced Settings 24 11a Radio Advanced Settings LAN WEP Field Description Field Description Finish to save the template. See Finishing the Template, Defining the 11a Radio Searched Channels Settings Defining the 11a Radio Data Encryption Settings 26 11a Radio Data Encryption Settings Configuring Devices Use this option to enable or disable local admin access Defining the Security SettingsSetting Local Admin Access Use this option to configure the device’s security settings Add Users-SeeAdding Users, Delete Users-SeeDeleting Users, Adding Users Procedure Deleting Users Setting Local AP/Client Security 28 Local AP /Client Security Settings Field Description Use this option to set up server-based security Setting Server-Based Security Procedure 29 Server-Based Security Settings 100 101 102 Configuring Services 103 Configuring Start-Up Settings 104 105 Field Description 106 107 Configuring Console/Telnet Settings 108 ANSI-Use this setting to offer graphicFeatures such as reverse video buttons Underlined links 109 Configuring Hot Standby Settings 110 111 Configuring Routing Settings 112 Configuring CDP Settings 113 Configuring DNS Settings Does not use DNS Configuring FTP SettingsDisable-Use this option if you network Select Services FTP. The Services FTP dialog box appears 115 FTP 116 Configuring Http Settings 117 Configuring Snmp Settings 118 Configuring Sntp Settings 119 Configuring Accounting Settings 120 121 122 123 Configuring Event Handling Configuring Events124 125 126 127 128 129 Configuring Event Notification 130 Configuring Custom Values 131 Previewing the TemplateKey Value Click Finish. See Finishing the Template, 132 Use this option to create a configuration templateCreating a Template Finishing the Template Click Edit. See Editing a Template, Copying a Template133 Deleting a Template Use this option to edit a configuration templateUse this option to delete a configuration template Editing a Template 135 Importing a TemplateClick Import. The Import Template window appears Import 136 Exporting a Template Managing Configuration Jobs137 Deleting a Job, Copying a Job, Viewing Job Run Details, Using the Templates,Job Choices Naming the Job 139 Selecting DevicesJob Name Enter a name for the job Description Enter a description of the job Click Select Template. The Select Template window appears Selecting a Template140 141 142 Scheduling a Job 143 Finishing the Job 144 Creating a Configuration JobViewing Configuration Job Status Viewing the Job, Filtering a Job, Editing a Job, 145 Viewing the Job You can stop a running job by clicking Stop Job Running146 147 Filtering a JobYou can do the following Refresh the screen-Click Refresh Click Delete Job Editing a JobDeleting a Job Copying a Job 149 Viewing Job Run Details Job Runs Details table displays the following information Viewing the Job Run Details Table150 Assigning a Startup Configuration Automating Configurations151 152 Configuration Template dialog box appears 153 Creating a Startup Configuration TemplateClick Save to save the template Click Delete to delete the template Tasks Template Choice Assigning an Auto-Managed Configuration154 155 Discover Device Credentials Http User/Password 156 Assigning Auto-Managed Configurations Select Configure Auto Update Auto-Managed Configuration Using Auto-Managed Options157 158 Managing Firmware Images Updating Device Firmware Editing Image Details on the WLSE, Viewing Images on the WlseImporting images-SeeImporting Images, Managing Firmware Jobs, Deleting Images from the WLSE, When you finish editing, click SaveEditing Image Details on the Wlse Image Details window opens Importing Images Deleting Images from the Wlse Importing Images from the Client System Desktop to the Wlse Details on the WLSE, Window is displayed. Complete the following Updating Device Firmware Managing Firmware Images Managing Firmware Jobs Using a Remote Tftp Server for Image Upload Click Job Name. The Job Name dialog box appears Managing Firmware Images, A-1 Selecting the ImageJob Name Enter a name for the job. For guidelines on naming Jobs, see Naming Guidelines, page A-1 Selecting Devices Scheduling the Job Email settings section Validate and Save section Remote server settings section Job Save Summary Window Job Validation Summary Window Details Creating a Firmware Job Using the Job Functions Creating a Firmware Job, Viewing Jobs by Job StateJob Name Job name Field Description Filtering Jobs Use this option to view details about a job Click OK in the popup windows Job Run Details Table Updating Device Firmware Managing Firmware Jobs Using the Device Center Using Reports For routers For more information, see Time Display Viewing the Fault Summary ReportFollowing table is displayed for the device’s fault summary Details, Viewing Device History Viewing Config HistoryFollowing table is displayed for the device’s history Job Name Job Type Viewing Firmware History Displaying a Client Detail Report Displaying Wireless Client Reports To export the report, click Export. See Exporting a Report, Address or nameClick Search. a list appears in the left pane Chose name, names are listed Displaying a Client Statistics Report Displaying a Client Historical Association Report Report, Administration Discover Tasks HistoryInventory Displaying Current Reports Individual Access Point and Bridge ReportsGroup Reports Individual Server Reports Individual Switch ReportsDisplaying a Group Report Individual Router Reports Displaying an EAP Authentication Fault Summary Report,Detailed Report, Displaying a Group Security Report Time the access point’s state last Report-Displaying an EAP Fault Summary-Viewing the FaultAuthentication Report, Summary Report, Displaying a Group Ssid Report EAP Authentication Report, Group Policy Report, Vlan Name Name of the Vlan Displaying a Group Vlan Report Column Description Displaying a Per Vlan Client Report Displaying a Group Policy Report Filters Report, Report-SeeDisplaying an AP Ethertype ProtocolReport-SeeDisplaying an AP IP Protocol Filters Displaying an AP IP Port Filters Report, Report-See Displaying an AP IP Protocol Filters Report, Displaying an AP Summary Report Current Client Association Report Displayed, one for each interface Authentication Report are also displayedDisplaying a Detailed Report From the Report Name list, select Detailed Report Unique identifier the client device uses to Column Description Displaying a Current Client Association Report Displaying an EAP Authentication Report From the Report Name list, select EAP Authentication Report Displaying an AP Ethertype Protocol Filters Report Displaying an AP IP Protocol Filters Report From the Report Name list, select AP IP Protocol Filters Displaying an AP IP Port Filters Report Displaying an AP Policy Report Displaying an AP Ethertype Protocol Filters Report From the Report Name list, select AP Policy ReportDisplaying an AP IP Protocol Filters Report, An AP IP Port Filters Report, Displaying an AP Qbss QoS Report 22 AP Qbss QoS Report Vlan Name Vlan name Displaying an AP Ssid ReportUnique identifier the client device uses to associate Vlan identification number Policy Report, Displaying an AP Vlan Report 24 AP Vlan Report 25 Per Vlan Client Report From the Report Name list, select Switch Summary Report Displaying a Switch Summary Report Bridge Connected to Switch Report Displaying an AP and Bridge Connected to Switch Report Displaying a Router Summary Report From the Report Name list, select Router Summary Report Displaying an AP and Bridge Connected to Router Report Displaying a Server Summary Report Performance Report RF Utilization, Displaying Trends Group Performance Report Ethernet Utilization, Displaying a Group Performance Report RF UtilizationServers 31 Group Performance Report RF Utilization Displaying a Group Performance Report Ethernet Utilization Unique identifier the client device uses Displaying a Top N Number of Associations ReportChannel Number Channel being used Displaying a Top N Percentage Errors Period of time for which you want trending information From the Report Name list, select Top N Percentage Errors Click View. a graph is displayed 36 AP and Bridge Ethernet Transmission Statistics Displaying Trends Displaying an AP and Bridge Performance Graph Displaying an AP and Bridge Performance Tabular Click View. The report is displayed Displaying Top N Busiest ClientsView. The right pane refreshes Period of list, select the number of days From the Report Name list, select Top N Busiest Clients Displaying Top N Client Error Rate Displaying a Server Response Time Graph Emailing a Report Exporting a ReportClick View. The following report displays To cancel the email, click Cancel Mailroute by selecting Administration Appliance ConfigureTo send the email immediately, click Send Now Scheduling Email Jobs Report Properties Column Description Viewing Email Job Details Subject Format Body Email Properties ColumnSchedule Properties Column Description Performing Administrative Tasks Managing Devices Using Discovery and Managing Devices Manage Devices Device Details Pane View Device Management History Specifying Device Credentials Specify Community Strings Select Administration Discover Device Credentials Snmp Community String Guidelines, Variable Description Community String Guidelines Specify the Http Username and Password Managing Device Discovery Overview Discovery Overview Discovery, Set Up Devices, Importing Devices, Managing Devices, Set Up DevicesSet Up Access Points and Bridges Tasks Procedure Add New User. The User User that you created Password,Specify the Http Username You can use the same Click User Information then click Task Procedure Set Up Routers and Switches Contact contact command Set Up AAA ServersContact command Location command Wlse Enabled? Affect on Display Enable Discovery Options Manage Devices, Set Up Discovery Filters Include Rules Exclude Rules Defined? Result Schedule DiscoveryAll devices are discovered Procedure Run Discovery Now Seeds dialog box appears Select Administration Discover Discover Run Discovery Now.Run Discovery Now Specifying Device Credentials, Related Topics Discovery Task History, Running InventoriesAbout Scheduled Inventories Viewing Inventory and Discovery Task History, Immediate Inventory of Selected Devices Immediate Inventory of All Devices Name Type of Job Viewing Inventory and Discovery Task History From a file see Import Devices from a File, Importing Devices Import Devices from a File Import Devices from CiscoWorks2000 Portportnumber Exporting DevicesImport Devices from a File, Schedule Discovery, Serveripaddress on portportnumber Type Information Description Manage Leap Servers Adding, Modifying and Deleting AAA ServersTo add, modify or delete a Leap server Text Box Description To add a Leap server Manage Radius Servers Manage EAP-MD5 Servers Overview Groups Managing GroupsOverview Groups, Creating, Editing, and Deleting Groups, System-Defined Groups Add a Group, Edit a Group, Delete a Group, Creating, Editing, and Deleting GroupsAdd a Group User-Defined Groups Naming Guidelines, page A-1 Creating a New Group Box optional Copying an Existing GroupYour new group will be added to the Subgroup Of list Edit a Group, Delete a Group, Overview Groups, Edit a Group Add a Group, Delete a Group, Overview Groups, Delete a Group Overview Groups, Edit a Group, Add a Group, Managing the Appliance Viewing Log File Reports Viewing Wlse Status Log Files Displayed Log File ContentWlse maintains the following log files Managing the Software Restarting the Wireless LAN Solution EngineManaging Device Discovery, Running Inventories, Viewing Software Status To define or redefine the repository, complete the following Defining the Repository Repository source ftp//hostname/path Creating a Local RepositoryFind the software you want on the FTP site Repository add package Creating a Remote RepositoryCreating a Local Repository, Installing Software Updates Browsing the Repository Installing Software Updates, Managing the Software, Viewing Software Update HistorySoftware Update History window displays the following Overview Security Installation Managing Security Overview Authentication ModulesRadius MS NT Domain Selecting an Authentication Module, Administering Users, Selecting an Authentication Module Https dialog box appears Select Administration Appliance Security SSL HTTPS. The SSLManaging SSL Https Overview Security, # firewall eth0 Disabling or Enabling Telnet and Selecting SSH Viewing the Last 10 Logged-On Users Select Administration Appliance Security Last 10 Logins Backing Up and Restoring Data Specifying the Backup Location Select Start Settings Control Panel Add/Remove Programs Select Administration Appliance Backup and Restore BackupClick Test Click OK Backing Up Data Select Administration Appliance Backup and Restore Restore Backing Up Data, Specifying the Backup Location, Using DiagnosticsRestoring Data Viewing and Creating a Self-Test Report Viewing and Creating a Status ReportViewing and Creating a Self-Test Report, Viewing Processes, Processes displayed, see Processes Displayed, Viewing ProcessesViewing and Creating a Status Report, Viewing Processes, Report displays the following Return code represents normal program operation. Any Daemon Information dialog box displays the following Processes DisplayedDaemon Information Process Name Description Setting the Current Time and Date on the Wlse Setting Up the Splash Screen MessageSystem Log Clock set hhmmss month day year To set the UTC time, use the following CLI commandSelect Administration Appliance TIME/NTP/NAME Specifying NTP Time Servers Specifying Name Servers Select Administration Appliance Configure MailrouteSpecifying an Smtp Mail Server Using Connectivity Tools Polling Interval Managing System ParametersParameter Description Inventory Performance Attributes Inventory Performance Attributes Polling Shown in Configure Jobs, FirmwareJobs, and Reports Scheduled Email Jobs Managing Roles Administering UsersModifying Your Profile, Naming Guidelines, page A-1 Managing Users, Add Users, Modify Users, Delete Users, Managing UsersAdd Users Use this option to To modify a user Modify Users Level, see the User Guide for the CiscoWorks Wireless LAN Solution Engine -From the online helpNaming Guidelines, page A-1 Managing Roles, Delete Users Use the My Profile tab to change your passwordSelect Administration My Profile Change password Modifying Your Profile Linking to a CiscoWorks2000 Server 78-14947-01 Frequently Asked Questions Frequently Asked Questions Faults, Configure, Firmware, Reports, Administration, Troubleshooting Feature Symptom Probable Cause Possible Solution Faults Configure Jobs ConfigureConfigure See Set Up Devices Device Credentials Administration DiscoverHttp User/Password Http credentials Community string on Access point or bridgeAccess point or bridge has Have firmware rights Job Run Log to identify Selecting AdministrationAppliance Status View Check if the Job Run Detail Credentials Snmp Select AdministrationEnter services stop Enter services start Firmware Jobs FirmwareFirmware Jobs Create Click jobvm.log ReportsReports Log File Wireless Clients Enter services stop toEnter services start to Time, select Administration Administration Administration Appliance Enter services stop to stop Discover Schedule Discovery or Discovered in AdministrationRun Discovery Now. See Managing Security AuthenticationAdmin User Admin Character Description Example Name and Description Allowable Characters Type Rules Command Reference CLI Conventions Using the CLICommand Privileges Checking Command Syntax Help for CLI Commands Command History Feature Command Summary Debugs and tests email settings Mail section on page B-34 Configures an Ethernet interface Interface section on B-30151 Reboots the system Reload section on page B-39 Reinitializes the database Reinitdb section on B-40 Wireless LAN Solution Engine’s B-44 Local repositoryLists, starts, or stops management Services section on B-46 Configuration On page B-50 Displays the Wireless LAN Solution Show websslaccesslog Engine’s Web access log On page B-57Displays the Wireless LAN Solution Show weberrorlog section Engine’s Web error log On page B-58 Displays syslog information Show syslog section on B-67 Displays the Wireless LAN Solution Show snmp-server sectionEngine’s Snmp configuration On page B-66 B-66 Telnets to an external host Telnet section on page B-72 Command Description ConventionsConfigures an snmp agent Snmp-server section on B-71 Configures Telnet access Telnetenable section on B-73 Syntax Description Privilege Level 0 CommandsExit Ping Usage Guidelines Show clockShow clock Show domain-name Related CommandsShow domain-name Clock Ntp server Interface Show interfacesShow process Show interfaces Show version Displays command output one screen at a time. PressExit paged output and return to the command prompt Show version Traceroute Traceroute -m 20 -w 10 cisco.com Ping Auth Privilege Level 15 Commands Test BackupBackup test Backupconfig Listbackup Restore Show backupconfig Backup Listbackup Restore BackupconfigBackupconfig hostname username password directory No backupconfig Holdtime TimerCdp Run Set Clock Ntp server Show clock This command sets the date and timeClock set 160000 dec 11 Erase config Erase configErase config This command erases the system configuration Examples FirewallFirewall eth 0-5public private icmp telnet ssh snmp https Hostname name GethostbynameHostname Gethostbyname host Hosts ImportNo import host hostname ipaddress hosts Host No import hosts Install configureInstall configure URL URL Value default save Default All Install listInstall list all full page updates Updates Install update EX-2.0 Install updateInstall update package name Following command installs the update EX-2.0 Interface Default Name Domain name e.g. cisco.com This command disables the Ethernet 1 interfaceIp domain-name Ip domain-name name no ip domain-name name Ip-address Name server IP address maximum Ip name-serverIp name-server Ip name-server ip-address No ip name-server ip-address Ip name-server ListbackupListbackup Ip domain-name User@host Backup Backupconfig Restore Show backupconfigMail Mail to user@host debug Mailcntrl clear log sendqueue userqueue Following command clears the WLSE’s email logMailcntrl clear Mailcntrl list Nslookup dns-name ip-address MailrouteNslookup Mailroute hostname ip-address Ntp server ip-address No ntp server ip-address Ntp serverNslookup hostname Ntp server This command configures the system to use an NTP serverNo ntp server ip-address Ntp server ip-address Shutdown ReloadClock Reload Repository source URL ReinitdbRepository Reinitdb Repository source ftp//209.165.200.224 Repository add Repository delete package all Repository deletePackage Detail Repository listRepository list local remote detail Remote Repository list local detail Following command stops the local repositoryRepository server Repository server stop start status Backup Backupconfig Listbackup Show backupconfig RestoreReleated Commands Restore restore name Netmask ServicesServices command Services status start stop Route # services status This command stops management servicesThis command starts management services This command shows services status Matchstring1 Show anilogShow anilog page include MatchString1 MatchString2 Include Show auth-http Show auth-cliShow auth-http Show auth-cli Show auth-http Show backupconfigBackup Backupconfig Listbackup Restore Show backupconfig Exit paged output and return to the command prompt Show bootlogShow bootlog Displays command output one screen at a time. Press Show cdp neighbor Show cdp neighborShow cdp run Reload Clock Show cdp run This command displays the CDP configurationShow collectorlog Show collectorlog page include matchstring1 matchstring2 Show config Show configThis command displays the system configuration Show daemonslog page include matchstring1 matchstring2 Show daemonslogShow daemonslog Show dmgtdlog page include matchstring1 matchstring2 Show dmgtdlogShow dmgtdlog Show webaccesslog page include matchstring1 matchstring2 Show webaccesslogShow webaccesslog Show weberrorlog page include matchstring1 matchstring2 Show weberrorlog Show import hosts Show websslaccesslogShow websslaccesslog page include matchstring1 matchstring2 Show import Show ipchains Show install logsThis command displays the imported host file Show install logs short long Show hosts Show hostsShow hosts Show ipchains eth0 Show maillog page include matchstring1 matchstring2 Show proc commandShow maillog Show proc Show repository Displays command output one screen at a timeShow repository status access-log Access-log Show route This command displays the currently configured routesShow route Show securitylog Show securitylog Show snmp-server This command displays the type of SSH that is enabledShow snmp-server Show ssh-version Show syslog Related CommandTo display syslog information, use the show syslog command This command displays syslog information Show tech Show telnetenableTelnetenable command Show telnetenable Show tech Show tomcatlog page include matchstring1 matchstring2 Following command shows if Telnet is enabled or disabledShow telnetenable Show tomcatlog Shutdown This command shuts down the systemShutdown Location Snmp-serverSsh Community Ssh-version ssh1 ssh2 both Ssh1 Enables SSH Ssh2 Both Enables both SSH 1 and SSH2Ssh-version Telnet Disable TelnetenableTelnetenable enable ip-addresses domains disable status Enable Username No username user1 Maintenance Image CommandsThis command removes the user account Username user1 password password1 privilege Fsck To check and repair the filesystem, use the fsck commandFollowing command checks and repairs the filesystem Fsck See also EAP-MD5 server , Leap server , and Radius See wireless bridgeGL-1 Need them Lower-layer protocol to treat its messagesGL-2 Secure Http with SSL secure socket layer. See also SSL Group of related faultsSee also AAA Servers to transfer files, such as text and graphic files GL-4 Media Interface Connector. Fddi de facto standard connectorMay still be used in older wireless networks See also AAA and WEP keys GL-5 Reflects their transmission quality and service availability Up to 32 characters long Including passwordsGL-6 GL-7 Called Greenwich Mean Time GMT and Zulu time WEP keys Configured as an access pointGL-8 IN-1 Numerics IN-2 IN-3 IN-4 CLI IN-5 IN-6 CLI B-2 IN-7 IN-8 IN-9 IN-10 GUI IN-11 IN-12 IN-13 IN-14 IN-15 IN-16 IN-17 SSL IN-18 IN-19 IN-20