Setting Up Association | Cisco Systems 1105 specification

Chapter 3 Configuring Devices

Using the Templates

Table 3-1 Express Template Settings (continued)

Field	Description

Ensure Compatibility with Cisco	From the list, select one of the following:
	• Enable—Use this setting to
	automatically configure the device to be
	compatible with other Cisco devices on
	your wireless LAN.
	• Disable—Use this setting to not
	automatically configure the device to be
	compatible with other Cisco devices on
	your wireless LAN.

Ensure Compatibility with	From the list, select one of the following:
2MB/sec Clients	• Enable— Use this setting to operate at a
	• Enable— Use this setting to operate at a
	maximum speed of two megabits per
	second.
	• Disable—Use this setting if you do not
	want devices to operate at a maximum
	speed of two megabits per second.

Step 2 Select one of the following:

•Preview to see your changes before you apply them. (See Previewing the Template, page 3-131.)

•Finish to save the template. (See Finishing the Template, page 3-132.)

•Another template category to configure more options. (See Template Categories, page 3-2.)

Setting Up Association

Use this option to set up spanning tree protocol (STP) on bridges and to set up filtering to control the flow of data through the access point.

	User Guide for the CiscoWorks 1105 Wireless LAN Solution Engine
3-8	78-14947-01

Image 62

Cisco Systems 1105 manual Setting Up Association, Finish to save the template. See Finishing the Template

Contents

Corporate Headquarters Copyright 2002, Cisco Systems, Inc All rights reserved N T E N T S Iii Setting Trap Notification Assigning an Auto-Managed Configuration Displaying an EAP Authentication Report Displaying a Server Response Time Graph Vii Command History Feature B-3 Viii Privilege Level 15 Commands B-17 Show ipchains show hosts B-61show maillog Show tech B-68 Xii Convention AudienceConventions Boldface font Paper Documentation Related DocumentationOption Network Preferences Xiv Online Documentation Obtaining DocumentationWorld Wide Web Documentation Feedback Obtaining Technical AssistanceOrdering Documentation Cisco documentation is available in these ways 800 553-NETS Xvii Cisco.comTechnical Assistance Center Xviii Cisco TAC Web SiteCisco TAC Escalation Center Xix Page Overview of the Wireless LAN Solution Engine A P T E R Understanding the Wlse User Interface Wlse Dashboard Tabs and Subtabs Main Tab Subtabs Performing Administrative TasksButtons Devices under management, run immediate inventories, view Device Name and IP Address Display Time Display Logging In and Out ProcedureCiscoWorks 1105 Wireless LAN Solution Engine Getting Started with Device Management Task Description and References Inventories, Administering Users,Managing Devices, page 6-2. After moving devices to Displaying Faults Settings, page 2-20 to set policies Description FieldDevices Severity State Name/IP Click Apply. The following table appears Column Fault details for Viewing Fault DetailsManaging Profiles, Notification Settings, Related Topics Column Description Family Product Type IfIndexConditions Description See Time Display, Fault History Managing Profiles Assigning a Profile to a Device, Viewing Devices, Creating a ProfileCopying a Profile Use this option to create a profile Use this option to rename a profile Renaming a ProfileEditing a Profile Use this option to edit a profile Use this option to delete a profile Deleting a ProfileAssigning a Profile to a Device Viewing Devices Profile Choices Specifying Security Policies Field Description Click Add to add the Ssid to the list, then go to Step Go to Step Complete the following StepComplete the following Specifying Fault Thresholds Setting Access Point Fault Thresholds Enable Poll Interval Settings Overloaded Continue to Step Setting Switch Fault Thresholds Degraded Go to step Step To set the new entries Setting Router Fault Thresholds Setting Server Response Time Notification Settings Setting Trap Notification Before You Begin Setting Syslog Notification Setting Syslog Notification, Emailing Faults, Setting Trap Notification, Emailing Faults, Emailing FaultsTo save your settings Attribute Description Procedure Setting Trap Notification, Setting Syslog Notification, Fault Monitoring Notification Settings Configuring Devices Using the Templates Template Categories Template ChoicesRelated Topic See Naming Guidelines, page A-1 Using Express TemplateNaming the Template Express Template Settings Configuring Devices Field Description LAN Setting Up Association Finish to save the template. See Finishing the Template, Defining Spanning Tree Protocol This option is used for only bridges Bridge Enable-Use this setting to enable STP onDisable-If you do not want STP enabled Configuring Devices Defining Address Filters Field Description Creating New Ethertype Filters Procedure Defining Ethertype Filters Creating New Ethertype Filters Settings Deleting Ethertype Filters Procedure Creating Special Cases Procedure Configuring Devices Deleting Special Cases Procedure Defining IP Protocol Filters Using this option you can also Creating New IP Protocol Filters Procedure Deleting IP Protocol Filters Procedure IP Protocol Filters Special Cases Settings Field Description Defining IP Port Filters Creating New Port Filters Procedure To create and enable port filters, enter the following Deleting Port Filters Procedure IP Port Filters Special Cases Settings Configuring Devices Configuring Policy Groups Filters Adding or Deleting a New Policy GroupTo add a new policy group, enter the following IP Protocol Protocol Filters Deleting an Existing Policy Group from a Device Configuring VLANs Add a new VLAN-SeeAdding a New VLAN, Setting on the switchEnter the following information To add a new VLAN, enter the following Created using Association Policy GroupsAdding a New Vlan Enter the identification number of the Vlan Field Description Vlan Configuring Quality of Service Deleting an Existing Vlan Procedure Quality of Service Settings Configuring Service Sets This option allows you to define service sets Using Association Policy Groups Add a new Service Set-SeeAdding a New Service Set,Adding a New Service Set Procedure Association VLANs Field Description Finish to save the template. See Finishing the Template, Deleting an Existing Service Set Procedure Defining Advanced Associations 10 Advanced Association Settings PortWarning-Indicates that an error or failure SystemWarning-Indicates that an error orProtocolWarning-Indicates that an error or ExternalWarning-Indicates that an error or Field Description Finish to save the template. See Finishing the Template, Identifier Configuring Port AssignmentsLists the port’s 802.11 radio drivers association Configuring Dscp to CoS Identifying the Ethernet Port Configuring the Ethernet PortUse this option to configure the device’s Ethernet port Setting Up Ethernet Filters Enter the following information to identify the port Filters you created using Association Ethertype Filters Filters you created using Association IP Port Filters Setting Up Hardware Defining the Ethernet Advanced Settings Ssid Disallowed under Association Address Filters Allowed under Association Address Filters Set as disallowed under Association Address Identifying the 11b Radio Port Configuring the 11b RadioUse this option to configure the device’s 11b radio Procedure Selected value is displayed Primary Port? From the list, select one of the followingEthernet Identification , Association IP Protocol Filters Setting Up 11b Radio FiltersAssociation Ethertype Filters Defining the 11b Radio Hardware Settings IP Port Receive Transmit 18 11b Radio Hardware Settings Field Description Configuring Devices Field Description Field Description Defining the 11b Radio Advanced Settings All traffic except packets sent to the MAC Disallowed-The access point discardsAssociation Address Filters Addresses set as allowed under Field Description Check, a security feature that protects None-Does not enable MICNMH-Enables MIC Message Integrity This setting is valid Field Description Defining the 11b Radio Searched Channels Settings 20 11b Radio Searched Channels Settings Identifying the 11a Radio Port Configuring the 11a RadioUse this option to configure the device’s 11a radio Ethernet Identification, Setting Up 11a Radio Filters Ethertype Receive Transmit Defining the 11a Radio Hardware Settings Right pane 23 11a Radio Hardware Settings 78-14947-01 Configuring Devices Field Description Defining the 11a Radio Advanced Settings 24 11a Radio Advanced Settings LAN WEP Field Description Field Description Finish to save the template. See Finishing the Template, Defining the 11a Radio Searched Channels Settings Defining the 11a Radio Data Encryption Settings 26 11a Radio Data Encryption Settings Configuring Devices Use this option to configure the device’s security settings Defining the Security SettingsSetting Local Admin Access Use this option to enable or disable local admin access Adding Users Procedure Add Users-SeeAdding Users, Delete Users-SeeDeleting Users, Setting Local AP/Client Security Deleting Users 28 Local AP /Client Security Settings Field Description Setting Server-Based Security Use this option to set up server-based security Procedure 29 Server-Based Security Settings 100 101 Configuring Services 102 Configuring Start-Up Settings 103 104 Field Description 105 106 Configuring Console/Telnet Settings 107 Underlined links ANSI-Use this setting to offer graphicFeatures such as reverse video buttons 108 Configuring Hot Standby Settings 109 110 Configuring Routing Settings 111 Configuring CDP Settings 112 Configuring DNS Settings 113 Select Services FTP. The Services FTP dialog box appears Configuring FTP SettingsDisable-Use this option if you network Does not use DNS FTP 115 Configuring Http Settings 116 Configuring Snmp Settings 117 Configuring Sntp Settings 118 Configuring Accounting Settings 119 120 121 122 123 124 Configuring EventsConfiguring Event Handling 125 126 127 128 Configuring Event Notification 129 Configuring Custom Values 130 Click Finish. See Finishing the Template, Previewing the TemplateKey Value 131 Finishing the Template Use this option to create a configuration templateCreating a Template 132 133 Copying a TemplateClick Edit. See Editing a Template, Editing a Template Use this option to edit a configuration templateUse this option to delete a configuration template Deleting a Template Import Importing a TemplateClick Import. The Import Template window appears 135 136 137 Managing Configuration JobsExporting a Template Naming the Job Using the Templates,Job Choices Deleting a Job, Copying a Job, Viewing Job Run Details, Description Enter a description of the job Selecting DevicesJob Name Enter a name for the job 139 140 Selecting a TemplateClick Select Template. The Select Template window appears 141 Scheduling a Job 142 Finishing the Job 143 Viewing the Job, Filtering a Job, Editing a Job, Creating a Configuration JobViewing Configuration Job Status 144 Viewing the Job 145 146 RunningYou can stop a running job by clicking Stop Job Refresh the screen-Click Refresh Filtering a JobYou can do the following 147 Copying a Job Editing a JobDeleting a Job Click Delete Job Viewing Job Run Details 149 150 Viewing the Job Run Details TableJob Runs Details table displays the following information 151 Automating ConfigurationsAssigning a Startup Configuration Configuration Template dialog box appears 152 Click Delete to delete the template Creating a Startup Configuration TemplateClick Save to save the template 153 154 Assigning an Auto-Managed ConfigurationTasks Template Choice Discover Device Credentials Http User/Password 155 Assigning Auto-Managed Configurations 156 157 Using Auto-Managed OptionsSelect Configure Auto Update Auto-Managed Configuration 158 Updating Device Firmware Managing Firmware Images Managing Firmware Jobs, Viewing Images on the WlseImporting images-SeeImporting Images, Editing Image Details on the WLSE, Image Details window opens When you finish editing, click SaveEditing Image Details on the Wlse Deleting Images from the WLSE, Deleting Images from the Wlse Importing Images Importing Images from the Client System Desktop to the Wlse Details on the WLSE, Window is displayed. Complete the following Updating Device Firmware Managing Firmware Images Using a Remote Tftp Server for Image Upload Managing Firmware Jobs Managing Firmware Images, Click Job Name. The Job Name dialog box appears Jobs, see Naming Guidelines, page A-1 Selecting the ImageJob Name Enter a name for the job. For guidelines on naming A-1 Selecting Devices Scheduling the Job Email settings section Remote server settings section Validate and Save section Job Save Summary Window Job Validation Summary Window Details Using the Job Functions Creating a Firmware Job Job Name Job name Viewing Jobs by Job StateCreating a Firmware Job, Field Description Filtering Jobs Click OK in the popup windows Use this option to view details about a job Job Run Details Table Updating Device Firmware Managing Firmware Jobs Using Reports Using the Device Center For routers Details, Viewing the Fault Summary ReportFollowing table is displayed for the device’s fault summary For more information, see Time Display Following table is displayed for the device’s history Viewing Config HistoryViewing Device History Viewing Firmware History Job Name Job Type Displaying Wireless Client Reports Displaying a Client Detail Report Chose name, names are listed Address or nameClick Search. a list appears in the left pane To export the report, click Export. See Exporting a Report, Displaying a Client Statistics Report Displaying a Client Historical Association Report Inventory Administration Discover Tasks HistoryReport, Group Reports Individual Access Point and Bridge ReportsDisplaying Current Reports Individual Router Reports Individual Switch ReportsDisplaying a Group Report Individual Server Reports Detailed Report, Fault Summary Report,Displaying an EAP Authentication Time the access point’s state last Displaying a Group Security Report Summary Report, Fault Summary-Viewing the FaultAuthentication Report, Report-Displaying an EAP EAP Authentication Report, Displaying a Group Ssid Report Group Policy Report, Displaying a Group Vlan Report Vlan Name Name of the Vlan Column Description Displaying a Per Vlan Client Report Displaying a Group Policy Report Report-SeeDisplaying an AP IP Protocol Filters Report-SeeDisplaying an AP Ethertype ProtocolFilters Report, Report-See Displaying an AP IP Protocol Filters Report, Displaying an AP IP Port Filters Report, Displaying an AP Summary Report Current Client Association Report From the Report Name list, select Detailed Report Authentication Report are also displayedDisplaying a Detailed Report Displayed, one for each interface Unique identifier the client device uses to Column Description Displaying a Current Client Association Report Displaying an EAP Authentication Report From the Report Name list, select EAP Authentication Report Displaying an AP Ethertype Protocol Filters Report Displaying an AP IP Protocol Filters Report From the Report Name list, select AP IP Protocol Filters Displaying an AP IP Port Filters Report Displaying an AP Policy Report Displaying an AP IP Protocol Filters Report, From the Report Name list, select AP Policy ReportDisplaying an AP Ethertype Protocol Filters Report Displaying an AP Qbss QoS Report An AP IP Port Filters Report, 22 AP Qbss QoS Report Vlan identification number Displaying an AP Ssid ReportUnique identifier the client device uses to associate Vlan Name Vlan name Policy Report, Displaying an AP Vlan Report 24 AP Vlan Report 25 Per Vlan Client Report Displaying a Switch Summary Report From the Report Name list, select Switch Summary Report Displaying an AP and Bridge Connected to Switch Report Bridge Connected to Switch Report Displaying a Router Summary Report Displaying an AP and Bridge Connected to Router Report From the Report Name list, select Router Summary Report Displaying a Server Summary Report Displaying Trends Performance Report RF Utilization, Servers Displaying a Group Performance Report RF UtilizationGroup Performance Report Ethernet Utilization, 31 Group Performance Report RF Utilization Displaying a Group Performance Report Ethernet Utilization Channel Number Channel being used Displaying a Top N Number of Associations ReportUnique identifier the client device uses Displaying a Top N Percentage Errors From the Report Name list, select Top N Percentage Errors Period of time for which you want trending information Click View. a graph is displayed 36 AP and Bridge Ethernet Transmission Statistics Displaying Trends Displaying an AP and Bridge Performance Graph Displaying an AP and Bridge Performance Tabular Period of list, select the number of days Displaying Top N Busiest ClientsView. The right pane refreshes Click View. The report is displayed From the Report Name list, select Top N Busiest Clients Displaying Top N Client Error Rate Displaying a Server Response Time Graph Click View. The following report displays Exporting a ReportEmailing a Report To send the email immediately, click Send Now Mailroute by selecting Administration Appliance ConfigureTo cancel the email, click Cancel Scheduling Email Jobs Viewing Email Job Details Report Properties Column Description Schedule Properties Column Description Email Properties ColumnSubject Format Body Performing Administrative Tasks Using Discovery and Managing Devices Managing Devices Manage Devices Device Details Pane View Device Management History Specifying Device Credentials Select Administration Discover Device Credentials Snmp Specify Community Strings Variable Description Community String Guidelines, Specify the Http Username and Password Community String Guidelines Managing Device Discovery Overview Discovery, Set Up Devices, Overview Discovery Tasks Procedure Set Up DevicesSet Up Access Points and Bridges Importing Devices, Managing Devices, Add New User. The User You can use the same Click User Information then click Password,Specify the Http Username User that you created Set Up Routers and Switches Task Procedure Location command Set Up AAA ServersContact command Contact contact command Wlse Enable Discovery Options Enabled? Affect on Display Set Up Discovery Filters Manage Devices, All devices are discovered Schedule DiscoveryInclude Rules Exclude Rules Defined? Result Procedure Specifying Device Credentials, Select Administration Discover Discover Run Discovery Now.Run Discovery Now Run Discovery Now Seeds dialog box appears Related Topics Viewing Inventory and Discovery Task History, Running InventoriesAbout Scheduled Inventories Discovery Task History, Immediate Inventory of Selected Devices Immediate Inventory of All Devices Viewing Inventory and Discovery Task History Name Type of Job Importing Devices From a file see Import Devices from a File, Import Devices from a File Import Devices from CiscoWorks2000 Import Devices from a File, Schedule Discovery, Exporting DevicesPortportnumber Type Information Description Serveripaddress on portportnumber To add, modify or delete a Leap server Adding, Modifying and Deleting AAA ServersManage Leap Servers To add a Leap server Text Box Description Manage Radius Servers Manage EAP-MD5 Servers Overview Groups, Creating, Editing, and Deleting Groups, Managing GroupsOverview Groups System-Defined Groups User-Defined Groups Creating, Editing, and Deleting GroupsAdd a Group Add a Group, Edit a Group, Delete a Group, Creating a New Group Naming Guidelines, page A-1 Your new group will be added to the Subgroup Of list Copying an Existing GroupBox optional Edit a Group Edit a Group, Delete a Group, Overview Groups, Delete a Group Add a Group, Delete a Group, Overview Groups, Managing the Appliance Overview Groups, Edit a Group, Add a Group, Viewing Wlse Status Viewing Log File Reports Wlse maintains the following log files Log File ContentLog Files Displayed Managing Device Discovery, Running Inventories, Restarting the Wireless LAN Solution EngineManaging the Software Viewing Software Status Defining the Repository To define or redefine the repository, complete the following Find the software you want on the FTP site Creating a Local RepositoryRepository source ftp//hostname/path Creating a Local Repository, Creating a Remote RepositoryRepository add package Installing Software Updates Browsing the Repository Software Update History window displays the following Viewing Software Update HistoryInstalling Software Updates, Managing the Software, Installation Overview Security Radius MS NT Domain Overview Authentication ModulesManaging Security Selecting an Authentication Module Selecting an Authentication Module, Administering Users, Overview Security, Select Administration Appliance Security SSL HTTPS. The SSLManaging SSL Https Https dialog box appears Disabling or Enabling Telnet and Selecting SSH # firewall eth0 Select Administration Appliance Security Last 10 Logins Viewing the Last 10 Logged-On Users Specifying the Backup Location Backing Up and Restoring Data Click Test Click OK Select Administration Appliance Backup and Restore BackupSelect Start Settings Control Panel Add/Remove Programs Select Administration Appliance Backup and Restore Restore Backing Up Data Restoring Data Using DiagnosticsBacking Up Data, Specifying the Backup Location, Viewing and Creating a Self-Test Report, Viewing Processes, Viewing and Creating a Status ReportViewing and Creating a Self-Test Report Report displays the following Viewing ProcessesViewing and Creating a Status Report, Viewing Processes, Processes displayed, see Processes Displayed, Return code represents normal program operation. Any Process Name Description Processes DisplayedDaemon Information Daemon Information dialog box displays the following System Log Setting Up the Splash Screen MessageSetting the Current Time and Date on the Wlse Specifying NTP Time Servers To set the UTC time, use the following CLI commandSelect Administration Appliance TIME/NTP/NAME Clock set hhmmss month day year Specifying an Smtp Mail Server Select Administration Appliance Configure MailrouteSpecifying Name Servers Using Connectivity Tools Inventory Performance Attributes Managing System ParametersParameter Description Polling Interval Jobs, and Reports Scheduled Email Jobs Shown in Configure Jobs, FirmwareInventory Performance Attributes Polling Modifying Your Profile, Administering UsersManaging Roles Naming Guidelines, page A-1 Managing Users, Use this option to Managing UsersAdd Users Add Users, Modify Users, Delete Users, Modify Users To modify a user Naming Guidelines, page A-1 Managing Roles, Wireless LAN Solution Engine -From the online helpLevel, see the User Guide for the CiscoWorks Modifying Your Profile Use the My Profile tab to change your passwordSelect Administration My Profile Change password Delete Users Linking to a CiscoWorks2000 Server 78-14947-01 Frequently Asked Questions Frequently Asked Questions Troubleshooting Faults, Configure, Firmware, Reports, Administration, Faults Feature Symptom Probable Cause Possible Solution See Set Up Devices ConfigureConfigure Configure Jobs Http credentials Administration DiscoverHttp User/Password Device Credentials Have firmware rights Access point or bridgeAccess point or bridge has Community string on Check if the Job Run Detail Selecting AdministrationAppliance Status View Job Run Log to identify Enter services start Select AdministrationEnter services stop Credentials Snmp Firmware Jobs Create FirmwareFirmware Jobs Log File ReportsReports Click jobvm.log Time, select Administration Enter services stop toEnter services start to Wireless Clients Administration Enter services stop to stop Administration Appliance Run Discovery Now. See Managing Discovered in AdministrationDiscover Schedule Discovery or User Admin AuthenticationAdmin Security Name and Description Allowable Characters Character Description Example Type Rules Command Reference Checking Command Syntax Using the CLICommand Privileges CLI Conventions Command History Feature Help for CLI Commands Command Summary 151 Reboots the system Reload section on page B-39 Configures an Ethernet interface Interface section on B-30Debugs and tests email settings Mail section on page B-34 Configuration On page B-50 Wireless LAN Solution Engine’s B-44 Local repositoryLists, starts, or stops management Services section on B-46 Reinitializes the database Reinitdb section on B-40 Engine’s Web error log On page B-58 Engine’s Web access log On page B-57Displays the Wireless LAN Solution Show weberrorlog section Displays the Wireless LAN Solution Show websslaccesslog B-66 Displays the Wireless LAN Solution Show snmp-server sectionEngine’s Snmp configuration On page B-66 Displays syslog information Show syslog section on B-67 Configures Telnet access Telnetenable section on B-73 Command Description ConventionsConfigures an snmp agent Snmp-server section on B-71 Telnets to an external host Telnet section on page B-72 Ping Privilege Level 0 CommandsExit Syntax Description Show clock Show clockUsage Guidelines Clock Ntp server Related CommandsShow domain-name Show domain-name Show interfaces Show interfacesShow process Interface Show version Displays command output one screen at a time. PressExit paged output and return to the command prompt Show version Traceroute Ping Traceroute -m 20 -w 10 cisco.com Privilege Level 15 Commands Auth Backupconfig Listbackup Restore Show backupconfig BackupBackup test Test No backupconfig BackupconfigBackupconfig hostname username password directory Backup Listbackup Restore Run TimerCdp Holdtime Clock Set Clock set 160000 dec 11 This command sets the date and timeNtp server Show clock This command erases the system configuration Erase configErase config Erase config Firewall eth 0-5public private icmp telnet ssh snmp https FirewallExamples Gethostbyname host GethostbynameHostname Hostname name Host ImportNo import host hostname ipaddress hosts Hosts Default Install configureInstall configure URL URL Value default save No import hosts Updates Install listInstall list all full page updates All Following command installs the update EX-2.0 Install updateInstall update package name Install update EX-2.0 Default Interface Ip domain-name name no ip domain-name name This command disables the Ethernet 1 interfaceIp domain-name Name Domain name e.g. cisco.com Ip name-server ip-address No ip name-server ip-address Ip name-serverIp name-server Ip-address Name server IP address maximum Ip domain-name ListbackupListbackup Ip name-server Mail to user@host debug Backup Backupconfig Restore Show backupconfigMail User@host Mailcntrl list Following command clears the WLSE’s email logMailcntrl clear Mailcntrl clear log sendqueue userqueue Mailroute hostname ip-address MailrouteNslookup Nslookup dns-name ip-address Nslookup hostname Ntp serverNtp server ip-address No ntp server ip-address Ntp server ip-address This command configures the system to use an NTP serverNo ntp server ip-address Ntp server Reload ReloadClock Shutdown Reinitdb ReinitdbRepository Repository source URL Repository add Repository source ftp//209.165.200.224 Package Repository deleteRepository delete package all Remote Repository listRepository list local remote detail Detail Repository server stop start status Following command stops the local repositoryRepository server Repository list local detail Restore restore name RestoreReleated Commands Backup Backupconfig Listbackup Show backupconfig Route ServicesServices command Services status start stop Netmask This command shows services status This command stops management servicesThis command starts management services # services status Include Show anilogShow anilog page include MatchString1 MatchString2 Matchstring1 Show auth-cli Show auth-cliShow auth-http Show auth-http Show backupconfig Show backupconfigBackup Backupconfig Listbackup Restore Show auth-http Displays command output one screen at a time. Press Show bootlogShow bootlog Exit paged output and return to the command prompt Reload Clock Show cdp neighborShow cdp run Show cdp neighbor Show collectorlog page include matchstring1 matchstring2 This command displays the CDP configurationShow collectorlog Show cdp run This command displays the system configuration Show configShow config Show daemonslog Show daemonslogShow daemonslog page include matchstring1 matchstring2 Show dmgtdlog Show dmgtdlogShow dmgtdlog page include matchstring1 matchstring2 Show webaccesslog Show webaccesslogShow webaccesslog page include matchstring1 matchstring2 Show weberrorlog Show weberrorlog page include matchstring1 matchstring2 Show import Show websslaccesslogShow websslaccesslog page include matchstring1 matchstring2 Show import hosts Show install logs short long Show install logsThis command displays the imported host file Show ipchains Show ipchains eth0 Show hostsShow hosts Show hosts Show proc Show proc commandShow maillog Show maillog page include matchstring1 matchstring2 Access-log Displays command output one screen at a timeShow repository status access-log Show repository Show securitylog This command displays the currently configured routesShow route Show route Show securitylog Show ssh-version This command displays the type of SSH that is enabledShow snmp-server Show snmp-server This command displays syslog information Related CommandTo display syslog information, use the show syslog command Show syslog Show tech Show telnetenableTelnetenable command Show telnetenable Show tech Show tomcatlog Following command shows if Telnet is enabled or disabledShow telnetenable Show tomcatlog page include matchstring1 matchstring2 Shutdown This command shuts down the systemShutdown Community Snmp-serverSsh Location Telnet Ssh1 Enables SSH Ssh2 Both Enables both SSH 1 and SSH2Ssh-version Ssh-version ssh1 ssh2 both Enable TelnetenableTelnetenable enable ip-addresses domains disable status Disable Username Username user1 password password1 privilege Maintenance Image CommandsThis command removes the user account No username user1 Fsck To check and repair the filesystem, use the fsck commandFollowing command checks and repairs the filesystem Fsck GL-1 See wireless bridgeSee also EAP-MD5 server , Leap server , and Radius GL-2 Lower-layer protocol to treat its messagesNeed them Servers to transfer files, such as text and graphic files Group of related faultsSee also AAA Secure Http with SSL secure socket layer. See also SSL See also AAA and WEP keys Media Interface Connector. Fddi de facto standard connectorMay still be used in older wireless networks GL-4 Reflects their transmission quality and service availability GL-5 GL-6 Including passwordsUp to 32 characters long Called Greenwich Mean Time GMT and Zulu time GL-7 GL-8 Configured as an access pointWEP keys Numerics IN-1 IN-2 IN-3 CLI IN-4 IN-5 CLI B-2 IN-6 IN-7 IN-8 IN-9 GUI IN-10 IN-11 IN-12 IN-13 IN-14 IN-15 IN-16 SSL IN-17 IN-18 IN-19 IN-20