Delta Electronics VFD-VL manual Group 7 Special Parameters

Chapter 4 Parameters

Group 7 Special Parameters

		Pr.	Explanation	Settings	Factory	VF	VFPG	SVC	FOCPG	TQCPG	FOCPM
					Setting
07-00			Brake Chopper Level	230V: 350.0~450.0Vdc	380.0	○	○	○	○	○	○
				460V: 700.0~900.0Vdc	760.0
	07-01		Brake ED Value Setting	0~100%	100	○	○	○	○	○	○
	07-02		DC Brake Current Level	0~100%	0	○	○	○
	07-03		DC Brake Time during Start-	0.0~60.0 sec	0.0	○	○	○	○		○
			up
	07-04		DC Brake Time during	0.0~60.0 sec	0.0	○	○	○	○		○
			Stopping
07-05			Start-point for DC Brake	0.00~120.00Hz	0.00	○	○	○	○
07-06			DC Brake Proportional Gain	1~500Hz	50	○	○	○
07-07			Dwell Time at Accel.	0.00~600.00sec	0.00	○	○	○	○		○
07-08			Dwell Frequency at Accel.	0.00~120.00Hz	0.00	○	○	○	○		○
07-09			Dwell Time at Decel.	0.00~600.00sec	0.00	○	○	○	○		○
07-10			Dwell Frequency at Decel.	0.00~120.00Hz	0.00	○	○	○	○		○
07-11			Fan Control	0: Fan always ON	2	○	○	○	○	○	○
				1: 1 minute after AC motor drive stops, fan will be OFF
				2: AC motor drive runs and fan ON, AC motor drive stops and
				fan OFF
				3: Fan ON to run when preliminary heat sink temperature
				attained
				4: Fan always OFF
	07-12		Torque Command	-100.0~100.0% (Pr. 07-14 setting=100%)	0.0					○
07-13			Torque Command Source	0: Digital keypad (KPVL-CC01)	2					○
				1: RS485 serial communication (RJ-11)
				2: Analog signal (Pr.03-00)
	07-14		Maximum Torque Command	0~500%	100	○	○	○	○	○	○
07-15			Filter Time of Torque	0.000~1.000 sec	0.000					○
			Command
	07-16		Speed Limit Selection	0: By Pr.07-17 and Pr.07-18	0					○
				1: Frequency command source (Pr.00-14)
	07-17		Torque Mode +Speed Limit	0~120%	10					○
	07-18		Torque Mode-Speed Limit	0~120%	10					○
07-19			Source of Torque Offset	0: Disable	0			○	○	○	○
				1: Analog input (Pr.03-00)
				2: Torque offset setting (Pr.07-20)
				3: Control by external terminal (by Pr.07-21 to Pr.07-23)
07-20			Torque Offset Setting	0.0~100.0%	0.0			○	○	○	○
	07-21		High Torque Offset	0.0~100.0%	30.0			○	○	○	○
	07-22		Middle Torque Offset	0.0~100.0%	20.0			○	○	○	○
	07-23		Low Torque Offset	0.0~100.0%	10.0			○	○	○	○
	07-24		Forward Motor Torque Limit	0~500%	200				○	○	○
07-25			Forward Regenerative	0~500%	200				○	○	○
			Torque Limit
	07-26		Reverse Motor Torque Limit	0~500%	200				○	○	○
07-27			Reverse Regenerative	0~500%	200				○	○	○
			Torque Limit
07-28			Emergency Stop (EF) &	0: Coast to stop	0	○	○	○	○	○	○
			Forced Stop Selection	1: By deceleration Time 1
				2: By deceleration Time 2
				3: By deceleration Time 3
				4: By deceleration Time 4
				5: By Pr.01-31
07-29			Time for Decreasing Torque	0.000~1.000 sec	0.000				○	○	○
			at Stop

Revision Nov. 2008, VLE1, SW V1.03 4-13