Delta Electronics VFD-VL manual ~100.0%

Chapter 4 Parameters

	Pr.	Explanation	Settings	Factory	VF	VFPG	SVC	FOCPG	TQCPG	FOCPM
				Setting
			11: Low-voltage during acceleration (LvA)
			12: Low-voltage during deceleration (Lvd)
			13: Low-voltage during constant speed (Lvn)
			14: Low-voltage at stop (LvS)
			15: Phase loss (PHL)
			16: IGBT heat sink over-heat (oH1)
			17: Heat sink over-heat (oH2)(for 40HP above)
			18: TH1 open loop error (tH1o)
			19: TH2 open loop error (tH2o)
			20: Fan error signal output
			21: over-load (oL) (150% 1Min)
			22: Motor over-load (EoL1)
			23: Reserved
			24: Motor PTC overheat (oH3)
			25: Reserved
			26: over-torque 1 (ot1)
			27: over-torque 1 (ot2)
			28: Reserved
			29: Reserved
			30: Memory write-in error (cF1)
			31: Memory read-out error (cF2)
			32: Isum current detection error (cd0)
			33: U-phase current detection error (cd1)
			34: V-phase current detection error (cd2)
			35: W-phase current detection error (cd3)
			36: Clamp current detection error (Hd0)
			37: Over-current detection error (Hd1)
			38: Over-voltage detection error (Hd2)
			39: Ground current detection error (Hd3)
			40: Auto tuning error (AuE)
			41: PID feedback loss (AFE)
			42: PG feedback error (PGF1)
			43: PG feedback loss (PGF2)
			44: PG feedback stall (PGF3)
			45: PG slip error (PGF4)
			46: PG ref input error (PGr1)
			47: PG ref loss (PGr2)
			48: Analog current input error (ACE)
			49: External fault input (EF)
			50: Emergency stop (EF1)
			51: Reserved
			52: Password error (PcodE)
			53: Reserved
			54: Communication error (cE1)
			55: Communication error (cE2)
			56: Communication error (cE3)
			57: Communication error (cE4)
			58: Communication Time-out (cE10)
			59: PU time-out (cP10)
			60: Brake chopper error (bF)
			61-62: Reserved
			63: Safety loop error (Sry)
			64: Mechanical brake error (MBF)
			65: PGF5 hardware error
06-22		Fault Output Option 1	0~65535 (refer to bit table for fault code)	0	○	○	○	○	○	○
06-23		Fault Output Option 2	0~65535 (refer to bit table for fault code)	0	○	○	○	○	○	○
06-24		Fault Output Option 3	0~65535 (refer to bit table for fault code)	0	○	○	○	○	○	○
06-25		Fault Output Option 4	0~65535 (refer to bit table for fault code)	0	○	○	○	○	○	○
06-26		PTC (Positive Temperature	0: Warn and keep operation	0	○	○	○	○	○	○
		Coefficient) Detection	1: Warn and ramp to stop
		Selection
06-27		PTC Level	0.0~100.0%	50.0	○	○	○	○	○	○
06-28		Filter Time for PTC	0.00~10.00sec	0.20	○	○	○	○	○	○
		Detection
06-29		EPS Voltage	48.0~375.0Vdc	48.0	○	○	○	○	○	○
			96.0~750.0Vdc	96.0
06-30		Setting Method of Fault	0: By settings of Pr.06-22~06-25	0	○	○	○	○	○	○
		Output	1: By the binary setting

4-12 Revision Nov. 2008, VLE1, SW V1.03